Parts for Ge AEM10ASH1: Room Air Conditioner Parts

This curtain assembly replaces the inner door curtain on compatible GE over-the-range and countertop microwaves to restore the door's interior cover and help maintain proper operation and shielding. It's a direct-fit replacement sold individually. What it does:

• Replaces a cracked, warped, or missing inner door curtain that can expose internal components
• Helps restore the door interior, which can reduce visible light leaks and improve door integrity
• Addresses issues such as rattling or loose interior door panels during operation
• Compatible with service procedures that require removing and replacing the door inner curtain

• 1 curtain assembly

• Unplug or disconnect power before starting any repair; service only with unit de-energized
• Handle door components carefully to avoid damaging glass, seals, or the new curtain
• Removing the outer door and/or inner door liner may be required;

This flat washer provides a secure, even load distribution for a fastener on the appliance, helping maintain proper assembly and reduce loosening or wear. Use it to replace a damaged or missing washer during repairs. What it does:

• Sits under a nut or bolt to spread load and protect the appliance surface
• Helps prevent fasteners from loosening due to vibration
• Restores proper spacing and alignment for connected parts
• Commonly replaced when you see corrosion, cracking, or a loose connection

• One flat washer

• Disconnect power and turn off water supply before starting any repair
• Tighten fasteners to a snug fit—avoid over-tightening which can crush the washer
• If adjacent parts show damage or corrosion, inspect and replace as needed

This nut with attached washer is a small securing fastener used to clamp appliance parts and prevent loosening. It provides a low-profile, integrated washer bearing surface for a reliable hold. What it does:

• Secures panels, brackets, or components to prevent movement and rattling
• Maintains clamping force where an integrated washer is needed
• Helps keep electrical and mechanical connections stable
• Common symptom: loose or vibrating parts, squeaks, or components that shift during use

• One nut with attached washer

• Disconnect power and water before servicing
• Use the correct socket or wrench to avoid rounding the nut
• Tighten to snug fit — avoid overtightening which can strip threads or damage parts
• If replacing a rusted or damaged fastener, inspect mating threads and replace as needed

This spring washer provides resilient tension to help keep screws and bolts from loosening on appliance assemblies. It's a simple replacement part that restores proper fastener tension and helps maintain secure connections. What it does:

• Applies spring force around a fastener to resist vibration-related loosening
• Commonly used on panels, brackets, and components that see movement or vibration
• Can reduce rattling and intermittent connection issues caused by loose hardware
• Works with 6 mm-diameter fasteners where a small lock-style washer is required

• Disconnect power and unplug the appliance before servicing
• Use the correct 6 mm fastener and proper orientation when reinstalling
• Tighten hardware to the OEM's recommended torque if available; avoid overtightening
• If other fasteners or parts are damaged, replace them to ensure a secure repair

A small mounting nut used to secure components and panels on compatible appliances. Replaces a loose or missing nut to restore stable, safe fastening and reduce rattling or wobble. What it does:

• Secures panels, brackets, or assemblies to the appliance frame
• Prevents fasteners from backing out during normal operation
• Helps stop rattling, vibration noise, and loose-fitting parts
• Restores proper alignment for attached components

• Disconnect power and water before beginning any repair
• Match threads and size before installation; hand-start the nut to avoid cross-threading
• Tighten securely with the correct socket or wrench, but do not overtighten
• If the original fastener was damaged, replace the mating bolt/stud as needed

The Display Circuit Board is an OEM part for GE window air conditioners. Mounted at the front of the unit, it operates the LED lighting and screen for indicating settings.  

Causes of a faulty display board can include damage from moisture intrusion over time compromising sensitive onboard electronics. Condensation and dust particles get trapped inside sealed front panels adding stress.

Symptoms of a bad display board involve:

• Random shutoffs or failure to latch on temperature settings
• Inability to maintain cooling or fans at set levels 
• Refusal to power on without control response  
• Noisy buzzing or humming coming from electrical areas

This genuine GE replacement preserves convenient readout and control options. Compatible with some Frigidaire, Midea, and EdgeStar units, proper functioning maximizes user-friendly operation. Compatibility with wireless remote devices is also maintained for distance control of indoor comfort.

This thermostat is the temperature control for room air conditioners. It senses temperature and cycles the compressor to maintain your set comfort level, helping restore consistent cooling when the original control becomes inaccurate or fails. What it does:

• Monitors temperature and opens/closes contacts to start and stop the compressor
• Helps the unit reach and maintain the temperature you select
• Helps resolve symptoms such as: AC won't turn on/off at the dial setting, runs continuously, short-cycles, or temperature adjustments have little effect
• Direct-fit replacement designed for the original mounting location

• 1 thermostat

• Disconnect power before servicing to avoid electrical shock
• Access the control panel; note wire locations and transfer any mounting hardware from the old part
• If your model uses a capillary sensing tube, route it exactly as original and secure in clips; do not kink or sharply bend it
• Reassemble, align the control knob, and test operation across several temperature settings

The Main Control Board is an OEM part for GE window air conditioners. It houses the microprocessors and electronic components responsible for operating all critical functions. 

Causes of a faulty main control board can involve damage from power surges over time or accumulated moisture intrusion into tightly sealed electrical compartments. Repeated temperature cycling puts heavy stress on sensitive semiconductors as well.

Symptoms of a bad main control board include:

• Refusal to power on or intermittent shutdowns   
• Inability to regulate cooling, fan speeds, or modes
• Strange electrical noises or burning smells  
• No response from control buttons or display 

This genuine GE replacement restores safe and dependable temperature management. Compatible with select Frigidaire, EdgeStar, and Honeywell models, it maximizes efficiency and performance.

This PCB support is a molded mounting bracket that holds the appliance control board securely in place to prevent movement and contact with other components. It helps maintain reliable electrical connections and reduces board stress during operation. What it does:

• Secures the control printed circuit board to the chassis or housing to prevent vibration or dislodging
• Keeps the PCB spaced from metal parts to reduce shorting or abrasion risk
• Helps maintain stable connector engagement to avoid intermittent electrical faults
• Commonly replaced when the original support is cracked, broken, or missing

• Disconnect power to the appliance before starting any repair to avoid shock or damage
• Handle the PCB and support carefully; avoid bending the board or stressing solder joints
• Use appropriate fasteners; replace any damaged clips or screws with OEM-specified hardware

Filter sub-assembly replaces the refrigerator's water-filter housing, holding the cartridge and directing water to the dispenser and ice maker. Restores secure cartridge seating and consistent water flow when the housing is damaged. What it does:

• Holds and seals the cartridge to help prevent leaks at the filter location.
• Directs filtered water to the dispenser and icemaker plumbing.
• Commonly replaced for leaks at the filter area, reduced water flow, or a loose/ill-fitting cartridge.
• Intended for cartridge-style refrigerator water-filter systems.

• Turn off the refrigerator water supply and relieve dispenser pressure before removing the old filter housing.
• Use basic hand tools; inspect and replace any worn O-rings or seals to ensure a proper seal.
• After installation, restore the water supply, check carefully for leaks, and run/flush water per refrigerator guidance.

This vertical louver restores proper airflow and appearance for the appliance's vent or air channel. It directs air and protects internal components while keeping the exterior looking finished. What it does:

• Directs and guides airflow through the appliance vent
• Protects internal components from large debris and improves venting performance
• Helps reduce rattling from a damaged or loose vent louver
• Restores the appliance's exterior look when the original louver is cracked or missing

• One vertical louver

• Disconnect power (or unplug) before accessing the vent area to avoid electrical hazard
• Remove any fasteners or clips holding the old louver; retain hardware
• Align the replacement louver with mounting slots or tabs and secure with original screws or clips
• If edges are sharp or fit is tight, wear gloves and test operation before reassembly