Parts for Ge AEW14ASL1: Room Air Conditioner Parts

This is the air filter assembly for select GE room air conditioners. It traps dust and lint before they reach the evaporator coil, helping maintain airflow and cooling performance.

• Captures airborne dust and lint to protect the coil and blower
• Helps maintain steady airflow and cooling efficiency
• Replace if cracked, warped, missing, or won't stay seated
• Common symptoms include reduced airflow and visible debris on the filter

• Unplug the unit before servicing
• Remove the front grille or filter access panel; slide the old filter out
• Install the new filter with airflow orientation matching the original
• Clean surrounding surfaces and reinstall grille before powering on

This Air Guide Frame helps direct airflow inside the appliance so exhaust and cooling air follow the correct path, protecting internal components and helping the unit vent properly. It's a direct-replacement exterior frame piece. What it does:

• Guides and channels air through the appliance's venting area to maintain proper airflow.
• Holds surrounding trim and ducting in position for a secure fit.
• A damaged or warped frame can cause restricted airflow, rattling, or misaligned trim.
• Restores proper airflow routing when replacing cracked, broken, or bent frames.

• One air guide frame

• Disconnect power (and gas, if applicable) before starting any repair.
• Remove surrounding trim or panels as required to access the frame; keep fasteners for reassembly.
• Inspect adjacent ducts, seals, and mounting tabs for damage and replace if needed.

This front panel assembly replaces the damaged or worn control/display bezel on compatible GE appliances, restoring the unit's user interface and appearance. It provides the mounting surface and openings for the control buttons and display. What it does:

• Replaces cracked, faded, or broken front bezel and restores button/display access
• Secures and aligns the control board and user interface components
• Helps resolve issues where buttons are hard to press or the front is cosmetically damaged
• Keeps internal controls protected from spills and debris

• Installation requires removing the appliance outer housing and disconnecting power first; unplug or switch off breaker before starting.
• Handle with care to avoid scratching the finished surface and to protect attached cables and clips.
• Reuse original fasteners unless replacements are specified by the manufacturer.
• If the control board or display components are damaged, this panel replaces only the outer/front assembly.

The Display Circuit Board is an OEM part for GE window air conditioners. Mounted at the front of the unit, it operates the LED lighting and screen for indicating settings.  

Causes of a faulty display board can include damage from moisture intrusion over time compromising sensitive onboard electronics. Condensation and dust particles get trapped inside sealed front panels adding stress.

Symptoms of a bad display board involve:

• Random shutoffs or failure to latch on temperature settings
• Inability to maintain cooling or fans at set levels 
• Refusal to power on without control response  
• Noisy buzzing or humming coming from electrical areas

This genuine GE replacement preserves convenient readout and control options. Compatible with some Frigidaire, Midea, and EdgeStar units, proper functioning maximizes user-friendly operation. Compatibility with wireless remote devices is also maintained for distance control of indoor comfort.

A replacement motor fan that drives the appliance fan to circulate air for cooling and venting. Restores airflow to help maintain normal operating temperatures and prevent performance issues related to poor ventilation. What it does:

• Spins the fan blade that moves air through the appliance for cooling and venting.
• Helps prevent overheating by enabling proper airflow across motor, electronics, or heating components.
• Supports normal cycling and temperature control when functioning properly.

• Disconnect power before accessing the unit; follow all safety warnings in the service manual.
• Removing covers or panels may be required; keep track of fasteners and hardware.
• Verify fan rotation and clearances during reassembly; do not force or modify the part.

This axial flow fan moves air through the appliance to help cool internal components and support proper airflow. Replacing a worn or damaged fan restores quiet operation and helps prevent overheating-related issues. What it does:

• Circulates air across internal components or heat exchangers to maintain proper operating temperatures
• Helps prevent overheating of electronics, motors, or heating elements
• Reduces abnormal noise caused by worn or imbalanced fan blades or bearings
• Supports consistent airflow for reliable appliance performance

• One axial flow fan assembly

• Disconnect power to the appliance before starting any repair
• Handle the fan blades carefully to avoid damage; align properly during installation
• Verify secure mounting and electrical connections before restoring power
• Test appliance operation after installation and observe for proper airflow and quiet operation

This indoor air thermistor is a refrigerator air temperature sensor that helps the control board monitor cabinet temperature for proper cooling performance. Replacing a failing thermistor restores accurate temperature sensing to help prevent spoilage and cycling issues. What it does:

• Senses interior air temperature and sends temperature signals to the fridge control board
• Helps the compressor and fans run at the correct times for stable cooling
• Commonly associated with symptoms like warm or fluctuating temperatures, excessive cycling, or cooling that never reaches the set point
• Works as part of the temperature control system—faulty sensors can cause incorrect defrost or cooling behavior

• Disconnect power to the appliance before accessing or replacing the sensor
• Handle the sensor lead and element carefully to avoid damage; avoid pulling on wires
• Reinstall in the original location and routing; secure connectors fully to ensure good electrical contact

This support to cabinet is a metal mounting bracket that secures the appliance to surrounding cabinetry for stable, rattle-free operation. It helps keep the unit aligned and prevents shifting or sagging during normal use. What it does:

• Anchors the appliance to the cabinet frame to maintain proper alignment and fit
• Reduces vibration and rattling caused by loose or worn fasteners
• Prevents the appliance from tilting or shifting when doors or controls are used
• Restores safe, stable mounting after damage or corrosion to the original bracket

• Disconnect power (and gas if applicable) and remove surrounding trim before starting
• Retain or replace mounting hardware as needed; use screws appropriate for cabinet material
• Position bracket squarely against cabinet and appliance mounting points, then tighten securely

This curtain assembly replaces a damaged or missing door trim curtain to restore proper fit and protect internal components while improving appearance. It's a direct-replacement component used on compatible GE appliances. What it does:

• Covers and protects internal door/frame openings to keep components shielded from debris and light
• Helps maintain correct door alignment and trim fit for smooth opening and closing
• Reduces rattling or vibrating noises caused by a loose or broken curtain piece
• Restores finished appearance when the original curtain is cracked, warped, or missing

• One curtain assembly

• Disconnect power to the appliance before starting any repair
• Installation typically requires removal of the outer door or trim panel and basic hand tools
• Handle parts carefully to avoid scratching trim or damaging clips; keep fasteners organized for reassembly

A replacement window locking bracket that secures the appliance window or inner door assembly for safe, stable operation. Restores proper window alignment and helps maintain a tight, secure fit to reduce rattling and movement. What it does:

• Secures the appliance window or inner door assembly to the frame
• Prevents the window from shifting or rattling during use
• Helps maintain a tight seal for consistent performance
• Commonly replaced when bracket is bent, broken, or missing

• One window locking bracket

• Installation requires basic hand tools; disconnect power before servicing if part is behind an energized assembly
• Handle sharp edges carefully and support the window/door while removing and installing the bracket
• If fasteners are damaged or missing, replace with equivalent OEM hardware