Refrigerator Control Panel Lcd Parts

This defrost thermostat senses evaporator temperature and shuts off the defrost heater once the coil warms, preventing overheating. Replacing a failed thermostat restores proper defrosting to stop ice buildup and stabilize refrigerator temperatures.

• Controls the defrost heater based on evaporator coil temperature
• Closes when cold to allow defrost; opens as the coil warms to end the cycle
• Protects against overheating during defrost
• Failure may cause frost/ice on the back wall or evaporator, poor cooling, or a heater that never energizes

• Disconnect power before service; evaporator fins and sheet metal are sharp
• Access the evaporator by removing the freezer rear panel; note wire routing and mounting
• Position the new thermostat in the same location for tight contact with the tubing; reconnect wires exactly as found
• Reassemble and monitor a defrost cycle to confirm heater operation

This refrigerator main control board manages the compressor, fans, and defrost system. Replacing a failed board can restore stable temperatures and reliable cooling performance when symptoms point to an electronic control failure. What it does:

• Regulates compressor and fan operation to maintain set temperatures
• Controls and times the automatic defrost cycle for the evaporator
• Interprets sensor inputs and distributes power to key components
• Failure symptoms include no cooling, warm temperatures, or erratic cycling
• Can present as heavy frost buildup, fans/compressor not engaging, or repeated relay clicking

• Includes: 1 main control board

• Disconnect power to the appliance before servicing
• Use ESD precautions; handle the board by its edges to avoid static damage
• Photograph/label connectors and move them over one at a time to the new board
• Ensure all plugs are fully seated and wiring is clear of sharp edges before restoring power

This temperature control thermostat regulates cabinet temperature by cycling the cooling system on and off. It helps your appliance hold the setting you select so food stays cold without unnecessary overcooling.

• Senses internal temperature and opens/closes electrical contacts to start or stop the compressor
• Maintains the setpoint chosen with the control knob
• Symptoms of a failing control include: too warm or too cold temperatures
• Runs constantly or won't run unless tapped/adjusted
• Temperature knob has little or no effect on cooling

• Disconnect power before servicing
• Note wire locations and take photos before removal
• Route the sensing capillary/bulb exactly as original; do not kink or sharply bend it
• Secure the sensing bulb in its clips and ensure good contact; set to mid-range and allow up to 24 hours for temperatures to stabilize

The Dispenser Control Board is an OEM part for Frigidaire refrigerators. It regulates dispensing functions for options like filtered water and ice. 

Causes of failure involve typical wear over extended periods of powering integrated circuits. Electrical faults or power fluctuations have the potential to damage sensitive components too.

Symptoms of a bad control board include:

• Water dispenser not working or responding properly
• Ice maker not producing ice as expected  
• Error messages relating to dispensing features
• Responsiveness issues with any dispensing controls

This OEM Frigidaire replacement is also compatible with some Electrolux, Maytag, and Kenmore refrigerator models too. 

This power supply board converts household AC into the low-voltage DC your refrigerator's electronic controls require. Replacing a failing module can restore power to the display and control circuitry.

• Converts incoming AC power to regulated low-voltage DC for control electronics
• Powers the main control, user interface, and other low-voltage components
• Intermittent operation or no cooling may occur when the control system loses power

• Disconnect power from the refrigerator before servicing
• Handle the board by the edges and use anti-static precautions
• Access location varies by model; remove necessary covers/panels to reach the board
• Photograph wiring and move connectors one at a time; ensure all plugs are fully seated before restoring power

This part is a moisture sensor control board that is used on dryer units. This component monitors the moisture levels within the dryer and adjusts the dry time during the automatic drying cycle. A new moisture sensor control board will be needed if the time is not advancing in the automatic drying cycle, even if it does advance in the timed dry cycle. Another sign is if the dryer continues to run after the clothing inside is dry. Unplug the dryer from its power source prior to replacing this component. The person performing this task may wish to wear work gloves to protect their hands.The moisture sensor control board is compatible with dryers that are manufactured by Kenmore, KitchenAid, Kenmore Elite, Whirlpool, Amana, Crosley, Maytag, Inglis, Sears Canada, Roper, and Sears. This part is sold individually and it is a genuine OEM replacement part that comes straight from the manufacturer.

This electronic board powers and controls the light at the refrigerator's water/ice dispenser. Replacing it restores reliable illumination and proper on/off operation so you can clearly see the dispenser area during everyday use.

• Supplies regulated power to the dispenser light circuit for consistent brightness
• Responds to dispenser/control inputs to turn the light on and off
• A failing board can cause flickering or dim lighting
• Common symptoms include no dispenser light, intermittent light, or a light that stays on

• Disconnect power to the refrigerator before servicing
• Access the board behind the dispenser panel/escutcheon; remove trim carefully to avoid damage
• Handle the board by the edges and avoid static discharge; ensure connectors are fully seated

The main power control board assembly regulates and routes electrical power to major appliance systems, restoring correct control of compressors, fans, defrost and other functions when the original control board fails. What it does:

• Serves as the appliance's central power/control circuit, distributing power to key components.
• Controls compressor and fan operation to support proper cooling cycles.
• Manages defrost sequencing and related timing functions.
• Common symptoms tied to a failing board: unit won't start or run, intermittent operation, blank or unresponsive display, or control-related error codes.

• Disconnect all power before attempting any service; verify power is off at the breaker.
• Handle the board by its edges and avoid touching components; use anti-static precautions when possible.
• Confirm diagnostics and wiring/connector compatibility before replacing the board; retain all mounting hardware for reinstallation.

This door mullion is the vertical flipper rail that mounts to a refrigerator French door. It swings closed to cover the center gap, helping complete the door seal and reduce warm air leaks and condensation between the doors.

• Provides the pivoting center rail that mates with the opposite door to complete the seal
• Replace if cracked, broken, warped, or if the flipper won't fold or spring closed
• Common symptoms: door won't close smoothly, visible gap/light between doors, moisture or frost along the center seam
• Helps restore a proper air seal for consistent cooling performance

• Disconnect power and clear door bins before servicing
• Open the door; release the upper and lower retainers and lift the old mullion off its hinge points
• Position the new mullion, secure the retainers, and verify it pivots and seals correctly
• Check door alignment and gasket contact along the center seam

This power supply PCB provides the low-voltage power and control interface needed for the appliance's electronic systems, restoring proper power distribution and control signaling for displays and components. What it does:

• Converts incoming mains to the low-voltage supply used by control circuits and displays
• Delivers stable power to electronic modules so buttons, LEDs and sensors operate correctly
• Can resolve symptoms such as no display, blank/black control panel, or intermittent loss of power to controls
• Helps prevent erratic behavior caused by voltage irregularities or failed onboard regulation

• One power supply PCB

• Disconnect the appliance from power before beginning work to avoid shock or damage
• Handle the board by the edges and avoid contact with components to reduce ESD risk
• Verify the part number on the replacement board matches the original before installation
• Reinstall screws, connectors, or grounding per the appliance's service instructions

This small switch board sits behind the refrigerator's dispenser/control panel and reads the ice/water inputs so the dispenser and light respond correctly. Replacing a failed board restores reliable dispensing and button response.

• Mounts in the dispenser/control housing and registers paddle or button presses
• Sends control signals to the water valve, auger motor, or light circuit as designed
• Common symptoms: no or intermittent dispensing, unresponsive buttons/paddle, dispenser light won't toggle
• Helps restore proper ice/water selection and dispenser operation

• Disconnect power to the refrigerator before servicing
• Remove the dispenser/user interface panel to access the board; support the wiring harness
• Note connector locations and transfer wires one at a time to the new board
• Handle electronics carefully and observe ESD precautions; verify operation before reassembly

Replacement board-switch that restores control to the appliance's user interface. Replaces a failed switch/control board to help recover unresponsive buttons, inconsistent function selection, or intermittent control operation. What it does:

• Acts as the control switch board that routes user commands to the appliance control system.
• Restores responsiveness when touchpads or buttons fail to register inputs or respond intermittently.
• Helps stop erratic function selection or unexpected cycling tied to a faulty control interface.
• Interfaces with existing harness and mounting points for a direct replacement fit when the identical part is required.

• Always disconnect power to the appliance before starting service to prevent shock or damage.
• Handle the board carefully; avoid flexing the PCB and keep connectors aligned when reinstalling.
• Use basic hand tools to remove the control panel or cover; verify all connectors are fully seated before testing.

This defrost timer assembly cycles the refrigerator between cooling and defrost modes to prevent excess frost buildup and help maintain consistent temperatures. Replace a failed timer to restore regular defrost scheduling and reduce icing. What it does:

• Advances the refrigerator between cooling and defrost cycles on a timed schedule.
• Stops missed defrosts that can cause frost buildup on the evaporator and reduced cooling efficiency.
• Addresses symptoms such as excessive frost/ice, inconsistent temperatures, or a freezer that runs constantly.
• Acts as the control that engages the defrost heater and returns the unit to cooling when the cycle finishes.

• Disconnect power to the appliance before servicing to avoid shock or injury.
• Access the timer via the control panel or rear service area; document wiring or take photos before disconnecting.
• Install the timer in the same orientation and reconnect wires to the original terminals; do not force connectors.

The Control Board Box is an OEM replacement part for Whirlpool refrigerators. Housed internally, it contains the digital control board that regulates all refrigerator functions. 

Symptoms of a faulty control board box include:  

• Lights or compartments not functioning properly
• Inability to adjust temperature settings  
• Fluctuating interior temperatures
• Refrigerator failing to power on or cool 

Causes can be moisture damage over time compromising electronics, accidental impact trauma to the plastic case, or standard component degradation during usage cycles. 

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, and Kenmore models.

A vertical mullion assembly that restores the finished trim along the refrigerator door edge and covers the gap between doors for a clean appearance. Replaces cracked, broken, or loose mullion trim to improve fit and finish. What it does:

• Covers the vertical gap between refrigerator doors and provides a finished interior edge
• Hides and protects any wiring or fasteners routed along the door edge
• Restores proper door trim when the original mullion is cracked, split, or loose
• Helps reduce visible moisture or frost build-up along the door seam caused by damaged trim

• Disconnect power to the appliance before starting any repair to avoid injury
• Typically installs with a few fasteners or snaps into place; keep mounting screws from the original part if reusing
• Handle trim pieces carefully to avoid cracking; use non-marring tools to pry if needed

This small permanent magnet is used in supported refrigerator assemblies to actuate a mating reed switch or metal keeper. It helps the appliance recognize a closed position or hold a light cover/door closed for proper operation. What it does:

• Works with a reed switch or ferrous keeper to provide position sensing or magnetic latching
• Helps ensure features dependent on closed position operate correctly
• Can resolve issues where a small cover or door won't stay closed
• Address erratic "door ajar" indications tied to magnetic sensing

• Disconnect power and water before servicing
• Note the original magnet's location and orientation; polarity matters for proper operation
• Seat the magnet fully in its pocket or holder and align with the mating switch/keeper
• Test the related function before reassembling panels and trim