Refrigerator Glide Line Mover Start Switch Parts

This starter is the compressor's start device. It energizes the start winding so the compressor can begin running, helping restore reliable cooling performance. What it does and common signs it's bad:

• Supplies initial current to the compressor's start winding; disengages once the motor is running
• Symptoms can include a warm refrigerator/freezer, compressor not starting, clicking or humming every few minutes
• Can show heat damage or rattling when shaken after failure

• One compressor starter

• Disconnect power before servicing and pull the unit forward for rear access
• Remove the compressor cover; note wire positions and device orientation
• Firmly seat the new starter on the compressor terminals and reconnect the harness; reinstall the cover
• Restore power and observe compressor start-up; use cut-resistant gloves and follow the product's service information

This replacement slide is the rail that mounts inside the freezer and supports the storage basket or drawer so it glides in and out smoothly. Replacing a worn slide restores smooth operation and keeps baskets properly aligned.

• Supports and guides the freezer basket/drawer during opening and closing
• Helps keep the basket level and correctly aligned on its track
• Common fix for cracked, warped, or broken rails
• Symptoms include binding, rough travel, derailment, or difficulty opening/closing

• Disconnect power to the appliance before servicing.
• Remove the basket, then unfasten and remove the existing slide; note its mounting position.
• Install the new slide using the original hardware; do not overtighten.
• Reinstall the basket and verify smooth travel.

This rail guide assembly supports and guides a refrigerator drawer as it slides in and out, keeping it aligned and operating smoothly. Replace a damaged rail to restore proper movement and prevent binding, tilting, or drawer derailment.

• Guides and supports the drawer along its track for smooth sliding
• Maintains proper drawer alignment and level
• Helps prevent the drawer from popping off the track
• Replace if the rail is cracked, warped, or worn
• Common symptoms: drawer sticks/binds, tilts, scrapes, or won't open/close fully

• Disconnect power to the refrigerator
• Remove food and the affected drawer/bin to access the rail
• Release retaining screws or tabs; note orientation and transfer any reusable parts from the old rail
• Install and secure the new rail; reinstall the drawer and test for smooth travel

Includes relay, overload and cover.

The Glide is an OEM part for Frigidaire ranges. It ensures smooth movement of the storage drawer, allowing you to easily access and organize your stored items.

A bad glide can be caused by wear and tear, damage, or lack of lubrication. Signs of a faulty glide include a sticky or jammed drawer, uneven sliding, or a drawer that doesn't close properly.

Symptoms of a bad glide can include:

• Difficulty in opening or closing the storage drawer.
• Uneven or jerky sliding motion of the drawer.
• Drawer getting stuck or not fully closing.

Replace your worn-out or damaged glide with this genuine OEM part to restore movement to your range's storage drawer. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

Replacement crisper pan for refrigerators that provides a flat, removable surface to hold fruits and vegetables and helps contain spills for easier cleaning and storage. What it does

• Holds produce and other refrigerated items securely in the crisper compartment.
• Contains spills and drips to protect the compartment below.
• Helps restore usable storage when the original pan is cracked, broken, or missing.
• Reduces mess and makes drawer cleaning faster.

• Remove all food from the crisper drawer before replacing the pan.
• Slide the old pan out, wipe the compartment clean, then position and slide the new pan into place.
• Most replacements are straightforward and require no tools; if the pan does not seat properly, check the refrigerator's parts diagram.

This drawer slide assembly supports and guides your refrigerator's drawer so it opens and closes smoothly. Replace a cracked or worn slide to restore proper alignment and stop sticking, dragging, or dropped drawers.

• Supports the drawer and provides smooth sliding action
• Maintains alignment to prevent binding or popping off the track
• Replaces cracked, warped, or seized slide components
• Typical symptoms: drawer hard to open/close, crooked, or falls off

• Disconnect power before servicing
• Empty and remove the affected drawer and any obstructing shelves for access
• Remove fasteners securing the old slide; transfer any reusable brackets/clips from the original if applicable
• Align and secure the new slide, then verify the drawer engages both tracks and glides freely

This compressor start relay (PTC) briefly powers the compressor's start winding to ensure reliable start-up. Replacing a failed relay can stop repeated clicking and help a non-starting compressor restore normal refrigerator cooling.

• Provides a timed, resistance-based boost to the compressor's start winding, then drops out of the circuit
• Common symptoms: compressor hums then clicks off, frequent clicking from the rear, warm fridge/freezer, intermittent cooling
• Mounts directly on the compressor terminals; works with the separate overload protector and, if equipped, a run capacitor
• Visible signs of failure may include heat damage, burnt odor, or loose/rattling pieces inside the old relay

• Unplug the refrigerator and remove the lower rear access panel to reach the compressor
• Note wire routing and orientation; transfer any harness/retainer and seat the relay fully on the compressor pins
• If a run capacitor is present, discharge it before handling and reconnect to the same terminals
• Inspect the overload and connectors; replace any heat-damaged components

This support is the structural piece that holds and aligns a shelf, rack, or panel within your appliance. Replacing a worn or broken support restores proper fit and stability to prevent wobble, sagging, and related damage. What it does:

• Provides stable mounting and positioning for the associated shelf, rack, or component
• Helps maintain alignment so parts sit or slide correctly
• Replace if cracked, deformed, loose, or missing
• Symptoms can include a component that sits unevenly, drops, or won't stay in place

• Includes 1 support

• Disconnect power to the appliance before servicing
• Allow any hot surfaces to cool; wear cut-resistant gloves
• Note the orientation of the original part; reuse existing fasteners if applicable
• Ensure the support is fully seated and secure before returning the appliance to use

This compressor start device energizes the refrigerator compressor's start winding to begin the cooling cycle, then disengages it. Replacing a weak or failed start device can restore reliable starts and address repeated clicking and warm/no-cool symptoms.

• Provides initial power to the compressor's start winding for reliable startup
• Disengages the start circuit once the compressor is running
• Common failure symptoms: compressor won't start, frequent clicking from the rear, refrigerator or freezer not cooling
• Heat damage or burnt odor on the old device may be present when it fails

• Unplug the refrigerator before servicing; wear cut-resistant gloves
• Remove the rear access panel to reach the compressor compartment
• Note wire positions; if your model uses a separate run capacitor, transfer it; move wires to the new device one at a time
• Align the device with the compressor terminals and press straight on until fully seated; reinstall any cover or retainer

This shelf support replaces a broken or missing bracket that holds a refrigerator shelf in place. Restore a level, secure shelf surface and stop sagging or unexpected drops with a simple, like-for-like replacement.

• Supports the edge of an interior shelf and keeps it level
• Locks the shelf into the cabinet/liner mounting point
• Common signs to replace: shelf sags or tilts, won't stay positioned, support is cracked, loose, or missing
• Helps prevent shelf movement that can lead to spills

• Disconnect power and remove items from the affected shelf before starting.
• Note the position and orientation of the old support to match placement.
• Snap or screw the new support into the existing mounting point; transfer any reusable hardware.
• Reinstall the shelf and verify it seats level and secure.

This slide assembly restores smooth, stable movement to your refrigerator drawer or basket so it opens and closes easily and stays aligned. Replace a worn or cracked slide to eliminate sticking, sagging, or track problems.

• Guides and supports the drawer/basket along the cabinet track
• Maintains alignment to prevent binding, rubbing, or popping off the rail
• Restores full, smooth travel for easier access to contents
• Common symptoms: drawer hard to open/close, sits crooked, falls off track, or makes scraping/clicking noises

• Disconnect power and remove the drawer and contents before starting.
• Note the slide's orientation; remove mounting screws/clips and the old slide.
• Install the new slide in the same position; transfer any snap-on brackets from the original if applicable.
• Reinstall the drawer, ensuring both sides are seated on the tracks, and test for smooth operation.

The Drawer Glide Gear is an OEM replacement part for Frigidaire refrigerators. It is a metal component located on each side of wire shelf tracks that work together to make shelf and drawer movements smooth. 

Causes of bad glide gears can include wear from years of extended usage, dents or deformation that restrict proper motion, or failure of lubricating parts inside the gear mechanism.

Symptoms of a bad Drawer Glide Gear include:

• Shelves or drawers that stick or fail to slide freely
• Noisy squeaking or grinding noises coming from shelf areas  
• Shelves difficult to properly align or position as needed

As a high-stress moving part, glide gears can degrade and lead to slothful storage access over time. Replace with this genuine OEM component for optimally smooth shelf performance on your Frigidaire refrigerator. The replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This replacement crisper pan sits beneath the refrigerator crisper drawer to catch spills and support stored produce, helping keep the drawer area clean and stable. Fits as the OEM service part for compatible Frigidaire units. What it does:

• Supports the crisper drawer and helps keep fruits and vegetables stable.
• Collects spills and juices to prevent them from dripping into the cabinet below.
• Restores proper drawer seating when a cracked or warped pan prevents full engagement.
• Helps maintain a cleaner, more sanitary drawer area.

• Remove stored food and slide the crisper drawer out to access the pan.
• Lift or unclip the old pan per your refrigerator's service instructions and slide the replacement into the same position.
• Handle carefully and inspect mating rails and seals; replace any damaged hardware before reassembly.
• No special tools required for most models; wear gloves if removing a cracked pan.

The SWITCH, MAGNET is an OEM part for LG refrigerators. It is a switch designed to function in conjunction with the magnetic door seal, indicating to the refrigerator when the door is open or closed. This allows the refrigerator to regulate temperatures properly based on door positioning. 

Symptoms of a bad switch, magnet can include:

•  Temperature control issues, with the fridge struggling to maintain proper coolness levels
•  The fridge fails to switch to energy-saving modes when the door is closed 
•  Lights not turning on or off correctly when the door is opened or closed

Replace yours today with this genuine OEM LG part to ensure consistent and reliable temperature control. This OEM LG part is also compatible with Sears/Kenmore.

Color: Black. Instruction sheet included.