Washer Liquid Valve Parts

This aerosol spray paint restores the graphite finish on appliance surfaces for quick, low-effort cosmetic touch-ups. Use it to cover small chips, scratches and scuffs so the exterior looks uniform again. What it does:

• Matches graphite appliance finishes for spot repairs and touch-ups
• Covers visible chips, scratches and minor surface scuffs
• Restores a uniform appearance on painted metal appliance surfaces
• Helps protect exposed metal from surface corrosion after repair

• Clean and dry the surface; remove grease, dirt and loose paint before spraying
• Shake can well and test spray on a scrap piece or inconspicuous area first
• Apply in light, even coats from a recommended distance; allow coats to dry between passes
• Use in a well-ventilated area, keep away from heat/open flames, and follow all safety and disposal instructions on the can

This inlet valve assembly controls the flow of water into the washer so cycles fill correctly and on schedule. A direct-fit replacement that restores proper water delivery and helps prevent overfilling or no-fill conditions. What it does:

• Opens and closes to allow cold and hot water into the tub during fill cycles.
• Responds to the washer's control signals to deliver the correct water amount.
• Commonly replaces a valve that leaks, won't fill, fills slowly, or causes continuous filling.
• Helps resolve related error codes or fill/level issues when caused by a faulty valve.

• Disconnect power and shut off both water supply lines before starting work.
• Drain remaining water from hoses and use caution when handling connectors.
• Inspect inlet hoses and seals; replace damaged hoses or seals to prevent leaks.
• After installation, restore water and power, then run a short test cycle to check for proper fill and leaks.

This mixing valve controls and directs hot and cold water into the washer to produce the desired fill temperature for each cycle. Replaces a worn or leaking inlet control to restore correct water selection and filling behavior. What it does:

• Directs hot and cold water to create the set wash or rinse temperature
• Opens and closes water flow during fill cycles so the tub fills to the correct level
• Commonly replaced for leaking, no-fill, or incorrect-temperature symptoms
• Works as the washer's water inlet/mixing control within the water valve assembly

• One mixing valve assembly (single unit as shown)

• Disconnect power and shut off both hot and cold water supplies before servicing
• Handle gently; avoid bending or stressing inlet ports and electrical connectors
• Verify hose and connector condition when reinstalling; tighten fittings to prevent leaks

This touch-up paint bottle restores small chips and scratches on painted appliance surfaces to improve appearance and help protect against rust. Easy-to-apply formula matches common appliance finishes for quick cosmetic repairs. What it does:

• Covers small chips, nicks and surface scratches to improve appearance
• Helps protect exposed metal from moisture and surface corrosion after damage
• Provides a precise application for targeted repairs on doors, panels and trim
• Can be used on painted steel and metal appliance surfaces (test in an inconspicuous area first)

• Clean and dry the repair area; remove loose paint and corrosion before applying
• Shake bottle well and apply sparingly with included applicator or a small brush
• Allow adequate drying time between coats and follow any manufacturer cure instructions on the label
• Wear gloves and work in a well-ventilated area; keep away from open flame and out of reach of children

The Inlet Valve is an OEM component specifically designed for GE washing machines. It controls water entry into the washer tub during designated points in wash cycles.

Symptoms of a bad inlet valve include: 

• Inability to fill with water or short fills during wash steps  
• Leaks or water constantly running from the inlet area of the washer
• Odd sounds, banging or skipping when the filling mechanism engages

Causes involve mineral buildup, corrosion, or stripped valve internals preventing proper closure after years of use. 

This GE OEM replacement inlet valve ensures precise water fill levels. Compatible with some Hotpoint, RCA, and Kenmore models as well, it maintains optimal cycle functioning. 

This dispenser valve assembly controls water flow to the fridge door dispenser for reliable dispensing and shutoff. It replaces a failed valve to restore proper water delivery and stop unwanted dripping or leaks. What it does

• Opens and closes the water passage when the dispenser actuator is pressed to deliver water to the glass.
• Seals the water line to prevent drips or continuous flow when the dispenser is idle.
• Helps stop intermittent dispensing or no-water issues caused by a faulty valve.
• Works with the door dispenser plumbing—electrical/connectors remain unchanged.

• Disconnect power and shut off the refrigerator water supply before starting.
• Remove the refrigerator door panel or access cover per your model's service instructions to reach the valve.
• Verify electrical connector seating and water line fittings are secure; replace any damaged tubing or seals.
• Test for leaks and proper dispensing after restoring power and water.

This touch-up paint kit restores the appliance's painted finish after minor chips, scratches and scuffs to improve appearance and help blend repaired areas with the surrounding surface. Easy spot repair for small cosmetic damage. What it does:

• Conceals small chips, nicks and surface scratches to improve cosmetic appearance
• Blends with the appliance finish for a less noticeable repair
• Helps protect exposed substrate from moisture after paint is applied
• Intended for small spot repairs — not for full-panel refinishing

• Clean and dry the repair area thoroughly before applying paint
• Lightly sand any loose paint or rough edges for best adhesion; wipe clean of dust
• Apply sparingly and allow adequate drying time between coats; follow product label directions
• Use in a well-ventilated area and keep away from children and pets

This water inlet valve assembly controls water flow into the washer tub, restoring correct fill and water selection so cycles start and run properly. It replaces a failed or leaking inlet valve to help the machine fill and pause as designed. What it does

• Opens and closes to allow cold and/or hot water into the washer during fill cycles
• Stops water flow when the machine reaches the set fill level
• Commonly replaces valves that leak, fail to fill, or cause the washer to overfill
• Works with the washer's control signals to route water only when needed

• Disconnect power and shut off household water supply before replacing the valve
• Tighten fittings to correct torque to avoid leaks; use new seals if provided or recommended

This touch-up paint restores the look of appliances with Mediterranean-colored finishes by covering small chips and scratches. It helps blend repairs for a cleaner, more uniform appearance without replacing parts. What it does:

• Covers minor paint chips, nicks and surface scratches to improve appearance
• Matches Mediterranean finish to help blend repaired areas with surrounding surface
• Helps protect exposed substrate from further wear or corrosion when applied to bare metal
• Ideal for small, visible repairs on exterior panels and trim

• Clean and dry the area before applying; remove loose paint and grease for best adhesion
• Shake well and apply thin, even coats; allow adequate drying time between coats
• Test on an inconspicuous area first to confirm color match
• Use in a well-ventilated area and keep out of reach of children

Bottle with brush. Color: New avocado. Size: 0.6 fl.oz.

This touch-up paint restores small chips and scratches on painted appliance surfaces to improve appearance and slow corrosion. It's a simple cosmetic repair that helps appliances look cared-for between major services. What it does:

• Covers minor paint chips, nicks and surface scratches
• Helps restore a uniform finish on exterior panels and trim
• Reduces likelihood of surface rust where bare metal is exposed
• Ideal for spot repairs on visible areas without repainting large panels

• One touch-up paint item for appliance finish

• Work in a well-ventilated area and protect surrounding surfaces
• Shake well and test on an inconspicuous spot before applying
• Apply sparingly in thin coats; allow each coat to dry per product instructions
• Keep out of reach of children and away from open flame

This triple water inlet valve replaces the refrigerator valve that controls water flow to the dispenser and ice maker. It restores proper water routing so the dispenser and ice maker can fill and operate as intended. What it does:

• Directs and controls incoming water to the dispenser, icemaker and other water circuits
• Opens and closes solenoids so the ice maker and dispenser can fill when called for
• Commonly used when the dispenser or ice maker won't produce water or fills weakly
• Can cause water to drip or run if the valve leaks or fails to seal

• Disconnect power and shut off the water supply before starting work
• Relieve water pressure and place towels/pans to catch residual water
• Handle electrical connectors and mounting hardware carefully; replace gaskets or fittings if damaged
• Test for leaks and proper operation after installation

The Valve is an OEM part for Whirlpool washing machines. It controls the flow of water into the washer tub at designated stages in the washing process. Water enters through the valve inlet and is distributed to internal components like the detergent dispenser, water pipes, and sump hoses. 

Causes of a bad valve can include mineral scale buildup inhibiting proper flow regulation over time, or cracks and leaks from wear and tear on rubber gaskets and seals. 

Symptoms of a bad valve include:

• Slow or incomplete fills during washing cycles  
• Water not dispensing correctly through hoses or dispensers
• External water leaks from the valve area
• Error codes related to water level or pressure issues

This OEM Whirlpool replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Water Inlet Valve is an OEM part for Whirlpool front-loading washing machines. It is an electromagnetic valve that precisely controls water intake into the washer during designated points in the cycle. 

Causes of a bad water inlet valve can include mineral buildup disrupting valve function over many years of use. Exposure to varying water temperatures may also decrease lifespan.

Symptoms of a bad water inlet valve include:

• Inability to fully fill the washer tub as needed for optimal cleaning  
• Fluctuating or absent water levels lead to inefficient cycles
• Water pressure or temperature regulation is impacted 
• Valve seizing could result in flooding inside the washer

This OEM Whirlpool replacement valve restores precise fill control and pressure regulation. Compatible models include some Maytag, Amana, Jenn-Air, and select Kenmore machines. Replace yours to maintain peak washing performance.