110-23442500 Parts

This drain hose coupling connects two sections of the washer drain hose to restore a watertight path for wastewater, helping prevent leaks and restore proper draining. What it does:

• Joins two drain hose sections or connects hose to a mating outlet for secure water flow
• Seals the hose connection to reduce leaks at the joint
• Restores proper draining when a damaged or missing coupling causes slow drain or leakage
• Designed to fit the OEM hose profile for a snug, stable connection

• One drain hose coupling as shown

• Turn off power and water supply before starting any repair
• Inspect hose ends for damage; trim to clean cut if required for proper fit
• Push hose ends fully onto the coupling and secure with manufacturer-recommended clamps

This spring damper assembly cushions and stabilizes the appliance drum during spin cycles, reducing vibration and helping maintain smooth, balanced operation. It restores proper drum support and motion control for safer, quieter performance. What it does:

• Absorbs and dampens drum movement to reduce vibration and banging during spin
• Helps keep the drum properly aligned to prevent wobbling or rubbing
• Can resolve symptoms such as loud thumping, excessive vibration, or uneven spinning
• Works as the suspension support between the drum and cabinet to improve cycle stability

• Disconnect power (and water, if applicable) before beginning any repair
• Handle springs and mounting points carefully—springs are under tension and can snap if released improperly
• Installation may require partial disassembly of the cabinet or drum; follow the OEM service manual or instructions

This factory fastener secures appliance panels and components for a tight, rattle-free fit. Replace a missing, stripped, or corroded screw to keep assemblies aligned and performing as intended.

• Fastens panels, brackets, or assemblies in place
• Helps reduce vibration and rattling caused by loose hardware
• Maintains proper alignment of parts to prevent premature wear
• Common signs you need it: missing screw, loose panel, vibration/buzzing noises, or hardware that won't tighten

• Disconnect power; for gas or water-connected appliances, shut off supply lines before service
• Match the screw to the original; verify size, length, and thread before installation
• Start threads by hand to avoid cross-threading; use the correct driver bit
• Snug only—do not overtighten, especially into plastic or thin sheet metal

This 3-position temperature switch is the user control that selects between three temperature settings, restoring reliable temperature selection and consistent performance. It replaces a worn or failed selector to recover intended temperature control. What it does

• Acts as the selector that routes the control signal to one of three temperature positions.
• Commonly used when temperature settings fail to change or the unit stays at one setting.
• Helps eliminate inconsistent temperatures or intermittent heating/cooling related to selector faults.
• Switches between preset temperature ranges without changing other controls.

• One 3-position temperature switch

• Disconnect power to the appliance before beginning any work.
• Note or label wire locations and take a photo before removing the old switch for correct reassembly.
• Handle connectors carefully; ensure secure, fully seated connections after installation.

This 4-position temperature selector switch controls oven heat settings so you can select the correct cooking temperature range. It replaces a worn or faulty selector to restore reliable temperature selection on compatible ranges. What it does:

• Selects among four temperature ranges for oven heat control
• Routes power to the oven heating element based on chosen setting
• Helps resolve symptoms like inability to change temperature setting or no response when selector is turned
• Works with compatible range/stove control assemblies that use a 4-position selector

• One 4-position temperature selector switch

• Disconnect power at the breaker before starting any repair to avoid shock
• Handle terminals carefully; ensure correct wiring orientation matches original
• Reassemble panels securely

This syphon breaker prevents dirty drain water from being siphoned back into the dishwasher, helping maintain proper draining and protect wash water from contamination. It's a direct-replacement drain air-break for compatible dishwashers. What it does:

• Stops backflow/siphoning from the household drain into the dishwasher
• Helps maintain proper drain performance and prevents wastewater re-entry
• Can reduce odors and cloudy or soiled dishes caused by contaminated wash water
• Works as part of the dishwasher's drain plumbing to preserve wash hygiene

• Disconnect power to the appliance and turn off water supply before servicing
• Replace only with identical part and ensure correct hose routing and secure clamps
• Inspect adjacent drain hoses and connections; replace damaged hoses or clamps as needed

This replacement sleeve fits over a rotating shaft to reduce friction and protect the mating surface, helping restore smooth operation and reduce noise. Use when a worn sleeve causes rubbing or uneven movement. What it does:

• Acts as a bushing to prevent metal-to-metal contact on a rotating shaft
• Reduces friction and wear on the shaft and surrounding components
• Helps stop rubbing, scraping, or squeaking noises caused by a worn sleeve
• Restores proper alignment for smoother, quieter operation

• Disconnect power (and gas, if applicable) before starting any repair
• Use basic hand tools; no special training required for most installations
• Inspect the shaft and mating surfaces; replace if excessively scored or damaged
• If press-fit, install carefully to avoid damaging the new sleeve; do not use solvents as a substitute for proper fit

This E ring is a small metal retaining clip that secures shafts, pulleys, and other rotating parts to prevent axial movement. It restores correct part positioning so assemblies run smoothly and stay aligned. What it does:

• Acts as a snap/retaining ring to hold components on a shaft or in a groove
• Prevents pulleys, bearings, or spacers from sliding out of place
• Common symptom: loose or shifting pulley, increased wobble, noise, or component disengagement
• Small, inexpensive part whose failure can allow adjacent parts to migrate and cause additional damage

• Disconnect power to the appliance before beginning any repair
• Use snap-ring pliers or needle-nose pliers and wear eye protection when installing or removing
• Ensure clip seats fully in the shaft groove and that mating surfaces are clean and undamaged
• Replace any damaged mating hardware rather than reusing a deformed clip

For end of drain hose.

A U-bend retainer designed to secure a U-shaped heating element or tubing in place, preventing movement and vibration for reliable operation. Fits as the replacement hold-down clip used on compatible Whirlpool HVAC and appliance assemblies. What it does:

• Secures U-shaped element or tubing to the appliance frame or mounting bracket
• Prevents rubbing or vibration that can lead to wear or noisy operation
• Helps maintain proper spacing and alignment of the element for consistent performance
• Used where a compact, U-shaped clamp is required to hold components safely

• One U-bend retainer clip as shown

• Inspect the surrounding area and replaced part for damage before installing
• Use basic hand tools; align clip over the U-bend and fasten to the designated mounting point
• Disconnect power and allow components to cool before attempting repair
• Replace with the exact OEM fasteners

This siphon break kit prevents wastewater from siphoning back into the dishwasher, helping keep the tub and dishes clean and reducing drainback issues. Fits the dishwasher drain assembly to restore proper draining function. What it does:

• Stops backflow by breaking the siphon effect in the drain line
• Works with the dishwasher drain hose and pump to maintain one-way drainage
• Helps address symptoms like water remaining in the tub, partial drains, or water backing into the tub
• Supports proper drainage to reduce odors caused by standing water

• One siphon break kit

• Disconnect power to the appliance and turn off the water supply before starting
• Inspect the drain hose routing and secure the siphon break at the recommended height per the dishwasher's service instructions
• Use basic hand tools; hose clamps or fasteners may be required

This hose coupling connects a flexible appliance hose to the appliance plumbing, restoring a secure water connection and preventing leaks. Ideal when a worn or damaged coupling causes drips or loose hose fit. What it does:

• Provides a secure connection point between an appliance hose and the appliance inlet
• Replaces cracked, broken or corroded couplings that can leak or allow the hose to detach
• Restores proper hose sealing to reduce water drips at the connection
• Compatible with the original inlet connection type and mounting orientation

• Turn off and disconnect appliance power and shut off the water supply before replacing
• Remove the old coupling and clean the mating surfaces; inspect hose and clamps for wear
• Use proper clamps and hand-tighten; avoid over-tightening which can damage fittings

This genuine replacement screw fastens appliance panels and components where a 10-32 thread is required, restoring secure connections and reducing rattling or loose parts. It's a simple, reliable fix for loose trim, panels, or brackets. What it does:

• Replaces stripped, lost or corroded 10-32 threaded screws used on panels, brackets, and trim
• Restores secure attachment to stop vibration, movement, or rattling
• Matches OEM thread form for correct fit and engagement
• Used where a short 10-32 machine screw is specified by the manufacturer

• One 10-32 x 3/8 screw

• Disconnect power and/or water to the appliance before starting any repair
• Use the correct screwdriver or nut driver to avoid cam-out and head damage
• Thread by hand to start, then snug—avoid over-tightening to prevent stripped threads or cracked parts
• If screw engages metal-to-metal, apply appropriate torque and secure fit before reassembling panels

This black replacement control knob restores safe, easy control of your appliance's settings. It provides the original user interface feel so you can select cycles and temperatures with a firm grip. What it does

• Replaces a cracked, stripped, loose or missing control knob so controls turn smoothly
• Engages the control shaft to select cycles, temperatures, or power settings depending on the model
• Improves user safety and operation by restoring a secure, easy-to-grip surface
• Matches OEM fit and appearance for a factory-style replacement

• One black control knob

• Always disconnect power (unplug or shut off breaker) before servicing the appliance
• Pull the old knob straight off the control shaft; align and push the new knob onto the shaft until fully seated
• Do not force parts; inspect the control shaft and spline for damage before installing

This 10-circuit connector housing provides a secure plug-style connection for the appliance wiring harness, restoring reliable electrical contact where the original plastic connector is cracked or melted. It helps ensure circuits stay seated and insulated. What it does:

• Replaces a damaged or cracked 10-circuit plastic connector housing to restore a proper plug connection
• Secures wiring harness terminals to prevent intermittent power or signal loss
• Keeps electrical contacts insulated from vibration and moisture
• Useful when the mating connector body is broken, burned, or otherwise unusable

• One 10-circuit connector housing

• Disconnect power to the appliance before starting any repairs
• Verify terminal pin type and wiring orientation before removing the old housing; take a photo for reference
• This listing is for the housing only; transfer existing terminals/pins or replace pins with exact matches as needed

This auger agitator moves ice through the refrigerator dispenser so cubes and crushed ice flow smoothly to the user. It replaces a worn or damaged auger to restore normal dispensing performance. What it does:

• Rotates inside the dispenser chute to push ice toward the dispenser outlet
• Helps prevent ice clumping and improves consistent dispensing
• Commonly replaced when ice won't dispense, dispenses slowly, or makes grinding noises
• Compatible with models that use a motor-driven auger assembly

• Disconnect power to the refrigerator before starting any repairs
• Remove the dispenser cover and ice bucket per your model's service instructions to access the auger
• Inspect for ice jams or broken plastic fragments before installing the new auger