30Cu Parts

The Oven Igniter is an OEM replacement part for Frigidaire ovens and ranges. This essential component is responsible for igniting the gas burners or bake and broil burners within the oven cavity, allowing for proper heating and cooking operations.

Causes of a faulty oven igniter can include normal wear and tear over time, exposure to excessive heat or debris buildup, or electrical malfunctions preventing proper ignition.

Symptoms of needing to replace the oven igniter include:

• Failure of the oven burners to ignite or light
• Delayed ignition or inconsistent burner lighting
• Visible damage or deterioration of the igniter element

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore ovens and ranges.

This sensor monitors operating conditions and relays accurate feedback to the control so cycles run properly. Replacing a failed sensor helps restore correct operation and prevent erratic behavior or fault codes. What it does:

• Detects a specific operating condition and sends a signal to the control
• Helps the machine regulate cycle timing and performance
• Can cause error codes, cycles that won't start or advance, or intermittent shutdowns when failing
• Lead to inconsistent temperatures or sensing behavior depending on application

• 1 sensor

• Disconnect power (and shut off gas/water, if applicable) before servicing
• Access the sensor; note wire positions and connector orientation
• Install the new sensor in the same location and orientation; seat connectors fully
• Clear any stored faults and run a test cycle per the tech sheet

This machine screw adjusts and secures the leveling leg or bracket, helping you set the appliance stable and plumb. Replacing a stripped, bent, or missing screw restores a solid footing and makes accurate leveling possible.

• Threads into the base or leveling bracket to raise or lower the appliance for proper leveling
• Helps reduce rocking, wobbling, and vibration from an unlevel installation
• Common signs of wear: stripped threads, bent hardware, corrosion, or a missing screw
• Useful during installation or when the existing adjustment screw no longer holds

• Disconnect power; shut off gas before working
• Support the appliance to relieve weight on the leveling point
• Remove the damaged screw; inspect and clean mating threads
• Start the new screw by hand to avoid cross-threading, then adjust height and snug

By Frigidaire. 2+0 module type. Employs two spark electrodes for manual surface ignition of a four burner range top with flash tubes to front and rear burners. Very popular module used on many different brands and models. Check by appliance model number, if not sure.

Replacement mounting screw that secures appliance panels, trim or brackets to restore proper fit and reduce rattles. A simple fastener that helps keep components stable for safe, quiet operation. What it does:

• Secures panels, trim pieces or internal brackets in place
• Replaces lost, stripped or damaged screws that cause loose parts
• Helps stop rattling, vibration or misaligned panels
• Restores proper alignment so doors and covers sit flush

• Use the correct screwdriver or bit to avoid stripping the head
• Do not overtighten — snug until secure to prevent damage
• Disconnect power before working near electrical components
• Keep small parts away from children and pets

This replacement igniter is the glow-style heating element that lights the gas burner in compatible gas dryers, restoring reliable ignition so the dryer can produce heat when calling for a cycle. What it does

• Heats to a glowing temperature to ignite burner gas when the dryer starts
• Replaces a cracked, broken, or non-glowing igniter that prevents the burner from lighting
• Common symptom: dryer runs but does not produce heat
• Also used when the igniter shows visible damage or fails continuity checks

• One igniter (glow bar)

• Disconnect electrical power and shut off gas supply before servicing
• Handle the ceramic/element carefully; the glow element is fragile and can break if touched or dropped
• Follow OEM service instructions and replace any suspect mounting hardware or sensors encountered during replacement

Hex jam nut (9/16-18 UNF) that secures threaded shafts and fasteners in laundry equipment, resisting loosening from vibration to help maintain alignment and reliable operation of assemblies that rely on tight, secure connections. What it does:

• Locks onto a 9/16-18 UNF threaded shaft or stud to prevent fastener rotation and axial movement
• Helps keep pulleys, collars, shafts or linkages from working loose during normal use and vibration
• Reduces wobble, noise or misalignment caused by loose threaded connections
• Used as a thin (jam) nut where space is limited or as a secondary lock nut

• Disconnect power and move the appliance to a safe, stable work area before servicing.
• Use the correct 9/16" wrench or socket; hold the mating fastener steady while tightening the jam nut.
• Do not overtighten; follow OEM service manual torque guidance if available and inspect threads for damage before reuse.

A replacement timing cam that positions the timer/timer shaft to control cycle sequencing in compatible Speed Queen washers, helping the machine advance reliably through agitation, drain and spin stages for consistent operation. What it does:

• Rotates with the timer to index cycle steps, enabling proper engagement of transmission/clutch and water/drain functions
• Common repair part when a washer won't advance between cycles, gets stuck on a single stage, or skips spin/agitate
• Ensures correct mechanical timing for cycle transitions when installed and aligned correctly
• Typical molded cam design built to match OEM timing profiles for reliable fit

• Disconnect power and follow OEM service procedures before removing the console or timer assembly
• Observe alignment marks and index position on the timer shaft during removal and installation
• Replace only with the exact part number to ensure proper fit
• Do not attempt electrical testing while the unit is powered