596 50692000 Parts

This wire harness connects key internal components so power and signals are routed correctly. Replace a damaged harness to restore reliable operation when the original wiring is burned, brittle, cut, or causing intermittent electrical connection issues.

• Carries electrical power and control signals between designated components
• Restores dependable connections when wires or terminals are heat-damaged, broken, or corroded
• Helps address no-operation or intermittent operation of the affected component(s)
• Common clues include scorched insulation, loose/burned connectors, or visible wire damage

• Disconnect power before servicing; shut off gas/water if applicable
• Photograph/label connections and routing before removal
• Route and secure wiring exactly as original, away from sharp edges, hot surfaces, and moving parts; reuse existing clips/ties
• Seat connectors fully and avoid pulling on wires during removal/installation

This refrigerator glass shelf restores a flat, easy-to-clean storage surface and helps contain small spills. Replace a cracked or missing shelf to regain usable space and keep items level and organized.

• Provides a sturdy, level platform for food storage inside the fresh-food compartment
• Helps contain minor spills to reduce drips onto lower shelves and drawers
• Replace when glass is cracked, chipped, shattered, or missing
• Common symptoms: items tipping, shelf won't sit level, reduced storage space, broken glass

• Remove food/items and the existing shelf before installation
• Handle glass with two hands; wear cut-resistant gloves and eye protection
• Slide the shelf into the correct rails/slots until fully seated and level
• If your model uses separate trim or a frame, transfer it from the original shelf as needed

"Y" Tube is being replaced. The old valve has a double water outlet, must change to this single outlet and eliminate the "Y" Tube.

Size: 5/16 to 1/4. Universal John Guess Push On

Replacement control knob that restores positive, easy-to-use control of appliance settings. Installs quickly to replace a cracked, stripped or missing knob so you can accurately select cycles, temperatures or timers. What it does:

• Fits onto the appliance control shaft to turn and select settings.
• Replaces knobs that are cracked, loose, hard to turn, or have stripped splines.
• Restores secure grip and precise selection of cycles, temperatures or timers.
• Matches factory fit and appearance when installed.

• Always disconnect power (and gas if applicable) before servicing the appliance.
• Remove the old knob by pulling it straight off the control shaft; align splines and push the new knob fully onto the shaft.
• If the knob does not seat easily, check shaft alignment and spline orientation before applying force.

This handle plug snaps into the handle opening to cover the exposed mounting hole and restore a clean, finished look. Replacing a missing or damaged plug also helps keep debris out of the handle cavity.

• Covers the handle's exposed screw/mounting hole for a finished appearance
• Snaps in for a secure, flush fit
• Helps keep dust and moisture out of the handle opening
• Common symptoms: missing plug, cracked or loose cap, visible hole in the handle

• Disconnect power if working near electrical components and allow any hot surfaces to cool
• Protect the finish; use a plastic pry tool to remove the old plug
• Align the new plug with the opening and press firmly until it seats flush
• Replace additional plugs as needed for a uniform look

This support mounts in the dispenser area to secure the ice housing assembly. It helps keep the chute and door properly aligned so ice dispenses smoothly and the opening seals as designed.

• Supports and positions the ice housing/chute assembly in the freezer door
• Helps maintain proper alignment and sealing of the ice door/flapper
• Reduces wobble or flex that can affect dispensing performance
• Typical signs it may be needed: loose or misaligned dispenser housing, ice or air leaking at the chute, frost buildup around the dispenser, inconsistent ice dispensing

• Disconnect power to the refrigerator before servicing
• Remove the dispenser trim/control to access the housing; handle wiring and tabs carefully
• Remove mounting fasteners, replace the support, and transfer any reusable hardware
• Reassemble, restore power, and test ice dispensing and chute seal

This auger motor powers the refrigerator ice-dispenser auger to move or crush ice for dispensing, restoring proper ice delivery from the door. It replaces the factory auger motor responsible for auger rotation. What it does:

• Drives the auger that moves or crushes ice so the dispenser can deliver crushed or cubed ice.
• Commonly used when the dispenser auger does not turn, dispenses little or no ice, or the motor hums but the auger stays stuck.
• Restores normal auger rotation and helps reduce abnormal grinding or scraping noises tied to a failed motor.

• Disconnect power to the refrigerator before starting any work.
• Remove ice and the ice bin before accessing the auger motor to avoid spills or blockages.
• Follow the refrigerator service manual for correct removal and reinstallation; retain mounting hardware and note wire/harness routing.
• After installation, restore power and operate the dispenser to verify auger rotation and ice flow.

This factory screw secures appliance panels, brackets, or trim. Replace a missing, stripped, or rusted fastener to restore a tight, rattle-free fit and keep components properly aligned in the intended OEM locations. What it does

• Fastens brackets, trim, or sheet-metal panels to the chassis
• Replaces worn, rusted, or missing hardware
• Helps eliminate loose panels, vibration, and misalignment
• Restores proper fit and support for affected assemblies

• Includes 1 screw

• Disconnect power and shut off gas/water before servicing
• Match this screw to the original location; lengths and thread types can vary by position
• Use the correct driver; start by hand and do not overtighten to avoid stripping threads
• If the receiving threads are damaged, repair/replace the mating clip or insert before installing

This genuine-style freezer door gasket creates a tight seal between the freezer door and cabinet to help maintain cold temperatures and reduce frost buildup. Replacing a worn gasket restores a proper seal and improves cooling efficiency. What it does:

• Seals the freezer door to keep cold air in and warm air out
• Helps prevent frost and ice buildup inside the freezer
• Reduces compressor run time caused by air leaks
• Can stop visible gaps or drafts around the freezer door edge

• Disconnect power and remove food before replacing the gasket; allow the freezer to reach room temperature if iced over
• Clean and dry the door sealing surface thoroughly before installing the new gasket
• Warm or flex the gasket slightly to seat it evenly in the channel; avoid overstretching
• Inspect the door retainer and ensure the gasket sits fully in the channel; use only appropriate, non-sharp tools to avoid damage

Size: 8 x 1-1/4 inch.

This grommet isolates the refrigerator's fan motor from its mounting bracket to reduce vibration and noise while keeping the motor secure. Replacing worn or missing grommets helps stop rattles and prevents the fan blade from rubbing.

• Cushions the fan motor to maintain proper alignment and clearance
• Absorbs vibration to help reduce humming, buzzing, or rattling sounds
• Helps keep the motor stable so the blade doesn't contact the shroud
• Common signs of failure include excess vibration, noise, or a loose fan motor

• Disconnect power to the refrigerator before servicing
• Access the fan motor area (rear of unit or inside the freezer, depending on model) and support the motor
• Remove mounting hardware and seat the new grommet fully in the bracket/mount
• The fan blade spins freely with even clearance before reassembling and restoring power

This right-angle elbow fits between the water supply line and the refrigerator's icemaker fill tube. It directs water cleanly into the icemaker and helps maintain a sealed connection to reduce drips and leaks. What it does:

• Connects the inlet water tubing to the icemaker fill tube at a 90-degree angle
• Routes water into the icemaker during the fill cycle
• Helps maintain a watertight connection at the rear of the cabinet
• Common symptoms: leaking behind the refrigerator, slow or no ice production, ice buildup near the fill area

• 1 fill tube elbow fitting

• Unplug the refrigerator and turn off the water supply; relieve line pressure before starting
• Access the rear lower area, place a towel for any residual water, and locate the elbow at the fill tube connection
• Release the clamp or retainer, disconnect the tubing, seat the new elbow fully, and resecure the line
• Turn water back on, check for leaks, then restore power and monitor the first ice fill

This replacement mounting screw secures appliance panels and components to restore proper fit and reduce rattling. Use when a damaged or missing screw causes loose trim, gaps, or vibrating noises; order by part number to ensure a match. What it does:

• Fastens panels, brackets, or trim to keep parts aligned and secure.
• Stops vibration and rattling caused by loose or missing screws.
• Common symptoms: visible gaps, loose panels, hardware falling out, or excess noise.
• Use the part number and/or existing screw to ensure correct size and thread before ordering.

• Disconnect power and water before accessing internal components.
• Use the correct screwdriver or bit to avoid stripping the head.
• Turn until snug; avoid over-tightening which can strip threads or crack trim.
• Keep small parts away from children and pets during repair.

This drain tube gasket seals the connection between the drain tube and its mating port to prevent leaks. A tight seal helps keep water where it belongs and protects surrounding components from moisture damage.

• Creates a watertight seal at the drain tube connection point
• Can help address water leaks around the drain area
• Deterioration, cracking, or hardening of the old gasket may cause seepage
• Replacing a worn gasket can restore proper leak prevention

• Unplug the appliance and shut off water supply before service
• Place a towel or pan to catch residual water when disconnecting the tube
• Inspect the tube and mating surfaces; clean before installing the new gasket
• Do not overtighten fittings; verify a snug, even seal and check for leaks on first run