66512723K31o Parts

The Hex-Head Screw is an OEM replacement part for use in Whirlpool dishwashers. This metal screw measures approximately ¾ inch long. Its primary purpose is to secure the dispenser bracket in place, ensuring stable operation. This hex-head screw is designed for use with compatible hexagonal tools. This makes installation and removal straightforward. This part is sold individually and is guaranteed to fit your dishwasher door panel. This screw is compatible with select Whirlpool brand models including Amana, Crosley, Estate, Inglis, Jenn Air, Kenmore, Kitchen Aid, and Maytag.

The Power Cord Kit is an OEM replacement part for Whirlpool dishwashers. It is a 3-prong grounded, 16-gauge cord that includes all the hardware needed for installation. Includes all hardware needed for installation.

Causes of a bad power cord can include normal wear and tear over years of use, accidental impacts or cuts to the wiring, or improper installation that damages components.

Symptoms of a bad power cord include:

• The dishwasher not turning on or completing cycles
• Warm or hot power cords during operation
• Frayed, cracked, or exposed copper wiring

This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air, and some Kenmore models.

This overfill control float sits in the dishwasher tub and rises with the water level to signal the float switch to stop filling. Replacing a cracked or sticking float helps prevent leaks and recurring fill issues. What it does:

• Rises with the water level to actuate the float switch and stop the inlet valve
• Helps prevent overfilling and water leaking from the door
• A float stuck in the UP position can cause no fill or short fill
• A float stuck DOWN or damaged can allow overfilling

• 1 overfill control float

• Disconnect power and turn off water before servicing
• Remove the lower rack; lift out the old float from its guide and clear any debris in the well
• Insert the new float, ensuring it moves freely and reliably actuates the switch when raised

This wheel mount assembly fits the dishwasher's upper rack track and provides the roller that lets the rack glide in and out. Replacing a worn or broken mount restores smooth movement and keeps the rack aligned on the rails. What it does:

• Supports and guides the upper rack along the side rails
• Replaces cracked, missing, or seized rollers that make the rack hard to slide
• Helps prevent the rack from popping off the track or sitting unevenly
• Can reduce scraping or squeaking noises when moving the rack

• One upper rack wheel mount assembly

• Disconnect power to the dishwasher before servicing
• Open the door and remove the upper rack by releasing the rail stops
• Depress the locking tab to remove the old wheel mount from the rail; align and snap the new assembly into place
• Reinstall the rack and rail stops; check for smooth rack travel

Quantity of ONE. Size: 8-18 x 5/8 inch. (#8 screw, 18 threads per inch, 5/8 inch long)

Color: Grey. 4oz bottle with brush used for touching up damage to your dishracks. For blue use W10840471. For white use WP676453. For tips use 676458.

This replacement screw secures panels, brackets, and other components in your appliance to keep them aligned and rattle-free. Replacing worn, stripped, or missing hardware restores a tight fit and helps maintain safe, quiet operation.

• Fastens panels, brackets, or internal parts to the cabinet/frame
• Helps maintain alignment to reduce vibration and rattling
• Replaces lost, stripped, or corroded screws
• Common symptoms: loose panels/trim, rattles, or a screw that won't tighten

• Disconnect power; shut off water or gas if applicable
• Match thread and length to the original; replace one at a time to keep alignment
• Start threads by hand to avoid cross-threading; use the correct driver
• Tighten snugly—do not overtighten, especially into plastic or thin sheet metal

This vent housing assembly mounts in the dishwasher door to guide humid air out of the tub. A secure, sealed housing helps prevent steam leaks and moisture damage while supporting proper airflow during the dry portion of the cycle.

• Provides a sealed mounting point for the door vent
• Channels moist air out during drying to protect the door and control panel
• Helps prevent steam or moisture from escaping at the top of the door
• Common symptoms: steam or dampness at the door top, water streaks on the front panel, or visible cracks/warping in the housing

• Disconnect power at the breaker and turn off water supply before servicing
• Remove inner door panel fasteners to access the vent area
• Note orientation; transfer any gasket or retainers from the original housing if required and seat the new housing flush
• Reassemble and run a short cycle to check for leaks and proper airflow

Color: White. 4oz bottle with brush used for touching up damage to your dishracks. For blue use W10840471. For grey use WP676455. For tips use 675679

This diverter disc directs wash water to different spray zones during a cycle, helping ensure alternating spray patterns and thorough cleaning. A worn or damaged disc can cause poor wash performance or incorrect spray routing.

• Routes water from the sump to selected spray arms/zones
• Helps alternate spray to improve coverage and cleaning
• Worn discs may lead to weak spray, poor cleaning, or unusual cycle behavior
• Can contribute to water leaking at the diverter area if the seal interface is compromised

• Disconnect power and water before servicing
• Access is typically from the bottom; remove the toe kick and lower panel as needed
• Note the disc orientation in relation to the diverter mechanism during removal
• Inspect related components (diverter motor/shaft, seals, sump) and replace if worn

This heater terminal nut fastens the heating element's electrical connector to its stud, keeping the connection tight under heat and vibration. Replacing a worn or missing nut restores safe contact and consistent heating performance.

• Secures the wire/ring terminal to the heater stud for a solid electrical connection
• Helps prevent arcing, discoloration, and heat damage from a loose connection
• Signs include a loose terminal, burnt odor, or melted/charred insulation at the heater connection

• Disconnect power and allow the appliance and element to cool completely before service
• Photograph wiring for reference; remove old hardware and clean the terminal
• Inspect the ring terminal, insulators, and stud; replace any heat-damaged components
• Start threads by hand to avoid cross-threading; snug with the correct nut driver—do not overtighten

This dispenser water tube routes water from the inlet to the refrigerator's in-door dispenser manifold, helping ensure a steady, leak-free flow to the dispenser.

• Directs water from the supply line to the dispenser manifold
• A damaged or cracked tube can cause leaks, low/erratic dispenser flow, or air in the water line
• Replacing a leaking tube can help restore normal dispenser operation and prevent water damage

• Unplug refrigerator and shut off water supply before service
• Have a towel/container ready to catch residual water
• Note tube routing and connections; push-to-connect fittings may require firm seating for a watertight seal
• After installation, turn water on and check all joints for leaks

This cap is a small protective cover used on select appliances to close off an opening or fastener. Replacing a damaged or missing cap helps keep out debris and moisture while restoring a clean, finished appearance.

• Covers an exposed opening or fastener to protect internal components
• Helps keep out dust, moisture, and spills
• Restores a clean, finished look and prevents snags
• Replace if the original cap is cracked, missing, discolored, or won't stay seated

• Disconnect power and, if applicable, shut off water or gas before service
• Remove the old cap by pulling straight off or unthreading, as designed
• Align the new cap and press or thread into place without forcing
• Verify a secure fit before restoring power and connections

This heater support holds the heating element securely in place inside the appliance, maintaining correct alignment and clearance for reliable operation. Replacing a worn or broken support helps prevent sagging, noise, or damage from an out-of-position element.

• Secures the heating element to its mounting point to keep it stable
• Maintains proper spacing from nearby components and surfaces
• Helps reduce vibration, rubbing, or rattling noises
• Replace if the original support is cracked, warped, missing, or the element appears misaligned

• Disconnect power to the appliance before servicing; allow hot components to cool
• Access the heater per your model's service information; note the original orientation and routing
• Seat the support fully and handle element leads carefully to avoid damage

This factory-spec screw secures panels and components in your appliance. Replacing a missing or stripped fastener restores a tight, rattle-free fit so parts stay aligned and operate as designed.

• Fastens brackets, panels, and internal components to their mounting points
• Maintains alignment and reduces vibration during operation
• Replaces missing, worn, rusted, or stripped hardware
• Helpful when you notice rattling, loose panels, gaps, or parts shifting out of position

• Disconnect power; shut off water or gas supply if applicable
• Align the part being secured and remove any damaged hardware
• Hand-start threads to avoid cross-threading; tighten with the correct driver
• Do not overtighten; verify the assembly is secure and operates freely

Bottle with brush. Color: Black. Size: 0.6 fl.oz.