790497113604 Parts

Evaporator fan motor that circulates cold air over the evaporator coil to help maintain even refrigerator temperatures. Replacing a failing motor restores airflow, reduces warm spots and frost buildup, and cuts down on excessive fan noise. What it does:

• Spins the evaporator fan blade to move cold air through the evaporator and into the cabinet.
• Promotes even cooling to prevent warm zones and food spoilage.
• Stops or reduces abnormal noises caused by a worn or seized motor.
• Helps prevent frost accumulation linked to poor airflow.

• Disconnect power to the appliance before beginning any repair.
• Handle the motor and fan blade carefully; ensure the fan blade is seated properly on the shaft.
• Remove evaporator/fan housing panels and retain screws and clips for reassembly; verify wiring connectors match before reconnecting.

This heat-resistant insulation helps contain oven heat and shield surrounding components. Replacing worn insulation supports faster, more consistent preheating, steadier baking temperatures, and cooler exterior panels for safer, more efficient operation. What it does:

• Wraps/lines the oven cavity or panels to reduce heat loss and protect nearby wiring and controls
• Helps the oven preheat efficiently and maintain consistent cooking temperatures
• Limits heat transfer to exterior panels and surrounding cabinetry
• Common signs of failure: longer preheat times, temperature swings, unusually hot sides/back, or insulation that is burnt, brittle, soaked, or missing

• 1 insulation piece

• Disconnect power and, if applicable, shut off gas before servicing
• Access typically requires removing rear/side panels or sliding the unit out; take photos to aid reassembly
• Wear gloves and a dust mask; handle gently—do not compress insulation and keep clear of sensors/wiring
• Re-secure with original clips/tape, reinstall panels, then test preheat and check for abnormal exterior heat

This high-temperature insulation is used in the oven assembly to contain heat and protect nearby components and cabinetry. Replacing damaged insulation helps the appliance maintain set temperatures and keeps exterior surfaces from getting excessively hot. What it does:

• Helps retain heat for stable baking and roasting temperatures
• Reduces heat transfer to the appliance frame and adjacent cabinets
• Replaces insulation that is torn, charred, or saturated with spills/grease

• One insulation piece

• Disconnect power; for gas models, also shut off the gas supply
• Remove the range or wall oven and access the oven body
• Wear gloves, eye protection, long sleeves, and a dust mask; fibers can irritate skin and lungs
• Reinstall in the same orientation/routing as the original; do not compress insulation or block vents

Replacement machine screw used to secure appliance panels and internal components, restoring a stable fit and reducing rattling. Matches a 10-32 thread with a 17/32-inch length for original fastener locations. What it does:

• Fastens panels, trim pieces, and internal brackets; a missing or damaged screw can cause loose panels or rattling noises.
• Secures knobs, control housings and small assemblies to prevent wobble or misalignment.
• Restores proper fit for components so doors and access panels sit evenly and function reliably.

• Disconnect power (unplug or shut off circuit) before accessing components.
• Use the correct driver and tighten by hand; avoid overtightening to prevent stripped threads or cracked plastic.
• Keep any original washers or clips and reinstall them with the screw.

This is a genuine replacement cover designed to protect internal components and restore the appliance's finished appearance. It provides a durable barrier that helps prevent dust, moisture, and accidental contact with internal parts. What it does:

• Covers and protects internal components behind the panel, maintaining appliance safety and appearance
• Helps prevent debris and moisture from reaching sensitive parts
• Restores a secure fit and alignment of the front/cabinet area
• Useful when the original cover is cracked, warped, or missing

• One replacement cover

• Disconnect power (and water, if applicable) before starting any repair
• Follow OEM service instructions for removal and reinstallation to avoid damaging adjacent components
• Use appropriate hand tools; avoid overtightening fasteners

This motor start/run capacitor helps the compressor and fan motors start and run reliably, restoring normal cooling performance when a failing capacitor causes hard starts or intermittent motor operation. A direct-replacement component for affected units. What it does:

• Provides the electrical phase shift and stored energy needed for compressor and fan motor startup.
• Helps prevent slow starts, humming, or motors that won't start reliably.
• Restores stable motor operation and can reduce overheating or tripping caused by a weak capacitor.
• Works as a replacement for the same OEM-design capacitor in compatible refrigerators and freezers.

• One replacement capacitor (single unit)

• Disconnect power to the appliance before inspecting or replacing the capacitor to avoid shock.
• Verify capacitor is fully discharged before handling; use insulated tools and follow safety procedures.
• Match the capacitor's mounting and terminal type to the existing part for correct fit and connection.

A replacement thermal (high-limit) fuse that restores the appliance's overheat protection by interrupting power if temperatures exceed safe limits. Use this part when the original fuse has opened or failed to protect the heating circuit. What it does:

• Interrupts the electrical circuit if the appliance overheats to prevent damage or fire risk.
• Stops power to the heating element or circuit when the fuse opens.
• Common symptom: appliance heats intermittently or not at all while controls operate normally.
• Common symptom: no continuity at the fuse when tested with a multimeter.

• Disconnect power to the appliance before servicing to avoid shock or injury.
• Locate the fuse per the appliance service manual or parts diagram; test continuity before replacing.
• Install the exact part; do not bypass the fuse or use substitutes that compromise safety.

This spring-loaded hinge supports and controls the oven door's movement so it opens smoothly and closes firmly, helping the door seal properly and retain heat. Replacing a worn hinge restores proper door alignment and closing force.

• Provides the pivot and spring tension for controlled door opening/closing
• Helps the door sit flush against the gasket to maintain a proper heat seal
• Common symptoms: door won't fully close, sags or drops, won't hold at a mid-open position, heat escaping from the front
• Typical causes of failure: metal fatigue, spring wear, or hinge deformation from heavy use

• Disconnect power; for gas models, also shut off gas. Allow the oven to cool completely.
• Support the door and engage hinge locks or remove the door.
• Springs are under tension—use gloves and eye protection; do not disassemble the hinge.
• Align with the receivers/slots and test for smooth operation and full closure; consider replacing both for even tension.

This spacer sets the correct gap between mating parts in your appliance's assembly, preventing rubbing and misalignment. Replace a missing or worn spacer to restore a solid fit, reduce noise, and protect surrounding components.

• Maintains proper spacing between components for correct alignment and operation
• Reduces metal-to-metal contact, squeaks, and premature wear
• Helps fasteners and panels seat securely
• Typical symptoms when failed: loose or rattling parts, uneven gaps, or visible wear marks

• Disconnect power; for gas models, shut off the gas. Allow the appliance to cool completely.
• Access the assembly per your model's diagram; note the original orientation/stack-up before removal.
• Reuse original fasteners if serviceable; hand-start threads and tighten snugly to avoid damaging the spacer.
• Verify alignment and clearances before fully reassembling. Quantity and location vary by model.

This latch hook is the replacement hook that secures a door latch assembly so the appliance door stays closed and operates correctly. It restores proper door engagement to prevent intermittent opening during use. What it does:

• Replaces a worn or broken hook that keeps the door latch engaged
• Helps the door stay closed and maintain a tight seal during operation
• Stops intermittent or failed latching that can interrupt cycles or operation
• Works as part of the door/latch mechanism to ensure consistent engagement

• Disconnect power (and water supply for dishwashers) before starting any repair
• Inspect the latch assembly and strike for wear or damage before installing the new hook
• Test door operation and cycle the appliance to confirm proper engagement after installation

This flexible door seal replaces a worn or damaged refrigerator door gasket to help restore a tight door closure and reduce air leaks. It fits into the door channel to help maintain proper cooling and reduce frost buildup. What it does

• Creates a compressible barrier between the door and cabinet to keep cold air in and warm air out
• Helps stop common symptoms like visible gaps at the door edge, excess frost/ice buildup in the compartment, and unstable interior temperatures
• Reduces strain on the compressor caused by air leaks and helps maintain consistent cooling
• Restores the appliance's intended seal when the original gasket is torn, stretched, or hardened

• One door seal

• Disconnect power to the appliance before starting and work on a cool, empty compartment
• Remove the old gasket fully and clean the channel or flange to ensure the new seal seats properly
• Press the new gasket evenly into the door channel; some models require gradual warming or light trimming for a perfect fit

This fuse and fuse holder assembly replaces the appliance's inline protective fuse and its mounting holder to restore proper overcurrent protection and reliable electrical connection. Use this part when a blown fuse or damaged holder interrupts power. What it does

• Protects appliance circuits by interrupting power when a fault or surge occurs
• Provides a secure, replaceable mounting point for the protective fuse
• Commonly associated with symptoms like no power, intermittent power loss, or an appliance that won't start
• Restores a safe electrical path when the original fuse or holder is damaged or corroded

• One fuse and one matching fuse holder

• Disconnect power to the appliance before inspecting or replacing the fuse and holder
• Verify the replacement matches the original fuse type and holder configuration before installation
• Inspect wiring and connectors for heat damage; replace damaged wiring or connectors as needed

This removable cooktop griddle provides a flat, durable cooking surface for preparing pancakes, sandwiches and other foods over range burners. It restores a smooth, even surface for stovetop griddle cooking when the original is damaged or worn. What it does:

• Replaces a worn, warped or damaged cooktop griddle to restore an even cooking surface
• Provides a flat, continuous surface for foods that need consistent contact with heat
• Helps reduce hot spots and sticking when the original griddle surface is compromised
• Works with compatible range/cooktop configurations that accept a removable griddle plate

• One removable cooktop griddle plate

• Disconnect power to the appliance (and turn off gas if applicable) before handling parts
• Allow the appliance and griddle to cool completely before removal or installation
• Fit the griddle into the cooktop openings so it sits flat and level; verify proper seating before use
• Clean per manufacturer guidance; avoid abrasive tools that can damage the cooking surface

A direct-replacement bake element that restores oven heat for baking and roasting. Replaces a worn or broken oven heating element to help return consistent baking temperatures and even cooking performance. What it does:

• Heats the oven cavity for baking and roasting.
• Commonly replaced when the oven won't reach temperature or baking is uneven.
• Works with electric ranges and wall ovens that use a separate bake element.
• Does not control temperature—works with the oven's thermostat and controls.

• One bake (oven) heating element.

• Disconnect power at the breaker before starting any repair.
• Typically mounts with two screws and connects to two terminal wires; verify terminals match before installing.
• Handle carefully to avoid bending or damaging the element; test after installation to confirm proper operation.