Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Fix a stuck or non-working ice/water dispenser with this micro switch. Common cause of dispensers running continuously or not activating. Easy DIY repair.
After my layman's diagnosis (hope) of a bad micro switch to the ice dispenser (would not activate and dispense ice through the chute) I purchased the both the ice and water dispenser micro switches (kill two birds with one stone). Albeit the video attached to these parts may be helpful to some it was not applicable to my refrigerator, as you could not access it from the front by removing the exterior dispenser plate. Don't try this on the LG, LFX25991ST series, refrigerator or you may break it... Read more
Creates an airtight seal around your refrigerator door to prevent warm air from entering. Replace if torn, cracked, or no longer sealing properly. Easy snap-fit installation. Confirm fit with your model number.
The right door seal and the freezer door seal are easily removed and replaced. They just pull out of the slot. These 2 new gaskets push in easily. The left door has the French Door Mullion, that blocks the removal of the door gasket. There are two screws in the middle that holds it on, and there is a spring at the bottom of the mullion that keeps the mullion in place. The spring can easily be removed, or left in place. There is an electrical connector in the middle of the mullion. As suggested... Read more
Controls ice dispenser door opening and closing. Replace if door won't open, stays open, or motor makes no sound when dispensing. Mounts behind dispenser trim.
Unplug refrigerator. Use non marring (plastic trim stick) tool to gently pry loose the plastic assembly containing the PCB display beginning at the lower edge and proceeding around the outer edge. Disconnect all connectors and note the routing of each wire harness and connector (take pictures on cellphone as necessary). Remove two screws holding inner PCB mount bracket in place to expose actuator, flapper door and linkage. Replace actuator (three mounting screws) and ensure that actuator... Read more
Fixes refrigerator running warm or compressor area overheating. This fan motor assembly circulates air over the condenser coils to regulate temperature.
Replaces the flap panel between French doors that seals the center gap. Order when original is cracked, broken, or won't stay closed properly.
Replaced the mullion, Read more
Fridge won't cool or evaporator coil freezing over? The defrost control assembly regulates cooling and defrost cycles. Moderate DIY repair.
Removed back cover in refrigerator to find the coil frozen. I ordered the part overnight and I replaced the defrost sensor, now all is well!! Fast and easy thanks to AppliancesPartsPros.com!! Read more
Hinge assembly for refrigerator doors. Installs at door pivot point to support door weight and enable smooth opening/closing. Replace if cracked or worn.
There is one hinge on top and one at the bottom, but it was none of these it ended up being this hinge that I ordered. Door was having a little hesitation at closing, the door would not pull your hand to close or it would not closed by itself. replaced this part and the refrigerator was fixed. Read more
Ice maker not producing ice or making small, malformed cubes? This ice maker assembly fixes inconsistent ice production. Moderately difficult repair.
Bought your craft ice maker. Read more
Seals the ice bank door to prevent warm air from melting ice and causing clumping. Replace if ice melts, refreezes into clumps, or frost forms around the bin.
We have an LG fridge that is 10 years old that was starting to have sweating problems around all the gaskets. So it was either a new fridge or try replacing the gaskets. I purchased a new ice maker door gasket using the parts catalog on the website. Very easy to order and they offer a short video to show the technique to switch out the old and new gaskets. Also did the same thing with the door gaskets and freezer drawer gasket. Website was very easy to work with and find the correct parts and... Read more
Replacement mounting stud for refrigerator door handles. Installs inside the door to secure handle assembly. Needed when stud is damaged or missing.
Ordered new freezer arm Read more
Fix a refrigerator that stopped making ice or produces slow, irregular ice cycles. This ice maker assembly restores automatic ice production. Moderate DIY.
Replaced with a new icemaker. Read more
Roller component for the ice dispenser door handle on bottom-mount refrigerators. Replaces broken, worn, or missing rollers. Ensures smooth handle operation.
Threaded bases for two roller screws were ~ 80% broken off. Used a short (just barely extends past the end of the roller) sheet metal screw to secure the roller in the upper sliding section of the handle (handle in place first). The head was thick enough to fill the gap between the roller and the cover. Filling that gap accurately is important. Need to keep the roller pushed into the recessed area in the door. (Do a test fit with the parts before trying to install them on the door). Turn the... Read more
Plastic water supply tube that connects the main water line to your refrigerator's dispenser and ice maker. Replace if cracked, leaking, or damaged.
Replaced 3 water lines on rear of refrigerator. Read more
Connects water tubing inside your refrigerator to supply the ice maker and water dispenser. Replace if cracked, leaking, or unable to hold tubing securely.
Replacement freezer door handle for bottom-mount refrigerators. Installs on freezer compartment door. Replace if broken, cracked, bent, or missing.
Replaces a cracked, broken, or missing ice dispenser door handle on your refrigerator. Installs on the exterior dispenser for easy ice access.