Bosch Shu3322uc/14 Parts

Support strap that cushions and secures the dishwasher circulation motor, stabilizing the motor assembly to reduce vibration and help maintain alignment for steadier, quieter operation. Designed for circulation motors with softer bearings. What it does:

• Cushions and supports the circulation motor to limit movement and vibration and reduce motor noise.
• Secures the motor assembly to the tub/chassis to maintain proper clearance and fit.
• Helps prevent undue stress on motor bearings and mounting points that can cause premature wear.
• Commonly replaced when the strap is cracked, stretched, or no longer holds the motor firmly in place.

• Disconnect power and water supply before servicing; follow all safety and OEM service instructions.
• Remove access panels and any obstructing components to reach the circulation motor as required.
• Replace using the original mounting hardware; inspect motor mounts and bearings while accessible.
• Reassemble and run a short test cycle to confirm reduced vibration/noise and proper motor operation.

This sump collects and channels dishwasher wash water into the wash pump, helping maintain proper drainage and reduce leaks at the tub-to-pump connection. Replace a cracked or damaged sump to restore correct water flow and sealing. What it does

• Directs wash water from the tub into the wash pump and drain system.
• Houses the pump inlet and seals the pump-to-tub interface.
• Prevents leaks by providing a secure seal between the tub and pump assembly.
• Common symptoms: pooling water in the tub, dishwasher not draining, leaks from the base, or unusual pump noise/vibration.

• Disconnect power and turn off the water supply before starting any repair.
• Handle carefully; inspect and replace any worn gaskets or seals when installing the new sump.
• Access typically requires removing lower access panels and the lower dish rack.
• After installation, test for leaks and proper drain operation before returning the appliance to normal use.

This is the right side hinge plate. For left side use 00298567.

This electronic control board manages the dishwasher's user console and cycle control, restoring reliable button response and cycle sequencing. Replace a failed control to regain normal operation and display feedback. What it does

• Receives input from the front console and runs selected wash cycles
• Controls timing, pump and heater activation according to program logic
• Restores response when touch/buttons, display, or LEDs are unresponsive
• Stops erratic or interrupted cycles caused by faulty control electronics

• One electronic control board / console control

• Disconnect power at the breaker before starting; confirm power is off
• Handle the board by its edges and avoid static discharge; use an anti-static wrist strap if available
• Some disassembly of the console or top panel may be required; keep track of screws and connectors

Bushing included. To order bushing separately use 00165296. This is the left side hinge. For right side hinge use 00263119.

This outer door is the dishwasher's exterior front panel that restores the appliance's appearance and protects internal components from damage. It provides a finished look and replaces dented, scratched, or corroded panels. What it does

• Covers and protects the inner door assembly, controls, and insulation from impact and moisture.
• Restores the dishwasher's exterior finish and alignment for proper sealing.
• Helps prevent further cosmetic damage and exposure-related corrosion.
• Resolves issues where visible dents, deep scratches, or rust affect the door surface.

• One outer door panel only.

• Disconnect power and water supply before starting any repair.
• Door panels can be heavy or awkward—have a second person assist to avoid dropping or bending the panel.
• Follow the manufacturer's service manual for correct removal/reinstallation steps and torque specifications.
• If trim, latch, or control components are attached, verify whether they must be transferred from the old door.

This is the left side hinge plate. For right side use 00298570.

This sump clamp secures the dishwasher sump/drain assembly to the tub, keeping the seal and pump assembly held in place to prevent leaks and movement. It's a small but essential fastener for a watertight sump connection. What it does:

• Holds the sump/drain housing tightly against the tub to maintain a proper seal
• Prevents the sump assembly from shifting during operation, which can cause leaks or noise
• Helps stop water from leaking under the machine when the pump runs
• Supports proper alignment of the drain/pump components for reliable draining

• One sump clamp

• Disconnect power and water supply before starting any repair
• Access the sump area by removing the lower access panel or toe kick and tilting the machine as needed
• Inspect the sump seal/gasket and replace if cracked or damaged when replacing the clamp
• Tighten clip until secure but avoid forcing or deforming the sump housing; test for leaks after reassembly

This door latch is the replacement latch assembly that secures the dishwasher door and helps the appliance start and run safely. It restores a reliable door closure for normal operation and cycle starts. What it does:

• Secures the dishwasher door closed so the machine can begin and complete wash cycles
• Helps prevent leaks by keeping the door sealed during operation
• Commonly replaces a latch that's broken, worn, or not engaging
• Resolves symptoms such as the dishwasher not starting, stopping mid-cycle, or the door not staying closed

• One door latch assembly

• Disconnect power to the appliance before attempting service
• Handle the latch carefully to avoid damaging the door trim or wiring harness
• Verify alignment and engagement of the latch with the strike when reinstalling
• Test the door operation and run a short cycle to ensure proper function after installation

This shaft for the float switch is the replacement shaft that secures and guides the dishwasher float to accurately detect water level, helping the appliance fill and shut off properly. Direct-fit design replaces the worn or broken float shaft. What it does

• Guides the float so the level-sensing switch can detect low or high water levels.
• Prevents overfilling by ensuring the float actuates the water-level switch reliably.
• Commonly replaces a cracked, bent or missing shaft that causes inconsistent fill, continuous filling, or water-level errors.

• One replacement float switch shaft.

• Disconnect power to the appliance before starting any repair.
• Remove the access panels and float assembly per your model's service instructions to reach the shaft.
• Inspect the float and switch for damage; replace only the failed components as needed.
• Reassemble carefully and test fill/stop operation before returning the appliance to service.