Cae2741fq1 Parts

The Screw is an OEM component compatible with Whirlpool washing machines. This screw secures the rear bulkhead to the tub, ensuring vibrations are reduced through solid mounting points. Properly installed screws dampen oscillating movement.

Causes of a bad screw include damage from water exposure like corrosion or breakage from stress concentrations if the tub bangs around during imbalanced loads. 

Symptoms of a bad screw include:

• Loose or detached rear bulkhead allowing side-to-side play
• Excessive noise and shaking felt through the surrounding walls   
• Development of micro-cracks around screw holes over time
• Potential leak paths if holes are no longer sealed 

This Whirlpool replacement screw restores a stable suspension system. It is compatible with additional brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Size: 1-1/16 x 5/8 inch. Used for fill hose. For a 4 pack order 285448A

This pushbutton installs in the control console and actuates the underlying switch, restoring positive, reliable selection of a cycle or feature and a clean, finished appearance when the original button is worn, sticky, or broken. What it does

• Provides the user-facing cap that presses the internal control switch
• Restores smooth button travel and positive engagement
• Helps ensure selections register consistently
• Common symptoms: button cap cracked/missing, sticks or won't spring back, selection only registers when pressed hard, loose or wobbly button

• 1 pushbutton

• Disconnect power before servicing to avoid electrical shock
• Access the control/console per your service manual
• Note orientation; release retaining tabs and remove old button
• Seat the new button fully; test travel and function before reassembly

Includes connector and both clamps.

This replacement nut is a small hardware fastener used to secure components inside your appliance. It helps keep parts tight and properly aligned so assemblies don't loosen from vibration or normal operation.

• Threads onto a mating bolt, stud, or shaft to clamp parts together
• Maintains alignment and reduces movement and rattling
• Replaces a stripped, missing, or damaged nut to restore a secure fit
• Common signs of failure: loose panels or components, unusual vibration/noise, hardware missing

• Disconnect power; shut off gas and/or water if applicable before servicing
• Note the original hardware stack-up (washers/spacers) and orientation for reassembly
• Start by hand to avoid cross-threading; tighten to manufacturer guidance—do not overtighten
• Replace any damaged washers or locking devices

The Capacitor is an OEM part for Whirlpool washers. It is responsible for starting the motor and keeping it running smoothly during the washing cycle. It stores electrical energy and delivers it to the motor when needed, providing the necessary power for the washer to function properly.

A bad washer capacitor can occur due to electrical malfunctions, wear and tear, or damage to the capacitor itself. If you notice symptoms such as the washer not starting or spinning, the motor making unusual noises, or the washer not completing cycles, it may be time to replace the washer capacitor.

Symptoms of a bad washer capacitor include:

• Washer not starting or spinning
• Unusual noises coming from the motor
• Incomplete cycles or erratic behavior

Repair your washer by replacing the faulty or worn-out washer capacitor with this genuine OEM part.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
 

Size: 29 1/4 inches x 31 1/4 inches. This universal washer drip tray is large enough for duet washers and sits under the washer to protect your floors from scuffs, spill, etc. Includes a PVC drain fitting.

Size: 8-18 x 1/2 inch.

Used from harness to top.

Right hand side. For screws use WPW10119828.

This is the appliance's water inlet valve. It controls and opens the water supply to the unit at the correct times so cycles can fill properly and dispense water where needed.

• Regulates incoming water flow to the appliance
• Can address no water to ice maker or dispenser
• May correct humming or buzzing from a stuck solenoid

• Disconnect power and shut off the water supply before servicing
• Keep a towel handy; a small amount of residual water may spill
• Transfer any mounting hardware or fittings from the old valve if required
• After installation, restore water, check for leaks, then test operation

This leveling foot threads into the base of the appliance to support and stabilize it. Proper adjustment keeps the unit level on uneven floors, reducing rocking, vibration, and noise for smoother, more reliable operation.

• Provides height adjustment to level and stabilize the appliance
• Helps reduce rocking, vibration, and rattling during use
• Restores support when an original foot is worn, stripped, or missing
• Can improve door/tub alignment once the unit is properly leveled

• Disconnect power and, if applicable, turn off water/gas before servicing
• Carefully tip or raise the unit to access the foot; use a helper to prevent tipping
• Thread the new foot by hand to avoid cross-threading; use a wrench for final adjustment
• Level the appliance front-to-back and side-to-side; ensure all feet firmly contact the floor

This coin funnel channels coins from the coin slide/drop into the collection box on coin-operated laundry equipment. Replacing a damaged or missing funnel restores smooth coin flow and helps prevent jams and lost coins inside the cabinet.

• Guides coins from the slide/drop into the collection/coin box
• Helps prevent coins from spilling into the cabinet and causing jams
• Cracks, warping, or misalignment can cause coin back-ups or coins showing up inside the machine
• Visible damage or frequent coin jams indicate the funnel should be replaced

• Disconnect electrical power before servicing; for gas dryers, also shut off gas supply
• Remove coin box and open the meter case/console to access the funnel
• Reuse existing mounting hardware; install the new funnel in the same orientation
• Clear debris and test coin travel by hand before reassembly and returning to service

Right hand side

This outer tub is the main water-holding housing for a top-load washing machine. It supports the inner basket and seals the wash chamber, helping the washer contain water and direct proper wash action. What it does:

• Holds wash water and surrounds the inner basket during fill, wash, and rinse cycles
• Supports the inner tub and transmission/agitator assembly for stable operation
• Prevents leaks by maintaining the sealed wash chamber; a cracked tub can cause visible water under the machine
• Helps reduce noise and vibration by keeping the wash components aligned

• One outer tub

• Disconnect power and water supply before beginning any repair
• Drain any remaining water from the tub and remove the washer cabinet or top to access the tub
• Transfer any components (basket, agitator, seals, mounting hardware) only if explicitly listed in your parts list; replace worn seals and gaskets when reinstalling

Size: .20 Fl. Oz. (6 ml)