De-410 Parts

This cycling thermostat regulates the dryer's heat by sensing exhaust air temperature and switching the heater on and off. Replacing a faulty thermostat restores consistent drying performance and helps prevent underheating or overheating.

• Monitors dryer air temperature and cycles the heating element or gas burner to maintain the proper range
• Helps prevent overheating that can trip safety limits
• Failure can result in no heat, low heat/long dry times, or heat that doesn't cycle correctly
• May cause intermittent shutdowns due to temperature issues

• Disconnect power; if gas, also shut off gas supply before servicing
• Thermostat is typically mounted on the blower housing or exhaust duct
• Note/transfer wires to the same terminals and secure the thermostat with existing screws; ensure it seats flush to the housing
• After replacement, clean lint buildup and verify proper vent airflow to avoid repeat temperature problems

This terminal insulator assembly isolates and supports an electrical connection where it passes through the appliance chassis. Replacing a cracked or heat-damaged insulator helps prevent shorts and restores a safe, reliable connection.

• Electrically insulates a live terminal from the metal cabinet or oven wall
• Provides a secure pass-through/mounting point for the element/wire connection
• Helps prevent arcing, shorting, and localized heat damage at the connection
• Typical symptoms: visible cracks or burn marks on the insulator, tripped breaker, intermittent or no heat due to a compromised connection

• Disconnect power at the breaker or unplug the appliance before servicing
• Access the terminal area; label or photograph wiring to ensure correct reassembly
• Transfer wires one at a time; reuse existing hardware if serviceable and tighten connections securely
• Inspect nearby wire ends/connectors and replace any that are heat-damaged or brittle

This 6-foot dryer vent duct connects your dryer's exhaust outlet to the wall vent. It provides a secure path for moist air to exit the home, helping maintain airflow and consistent drying performance. What it does:

• Vents hot, moist air from the dryer to the exterior
• Replaces crushed, torn, or lint-clogged ducting
• Helps address longer dry times, heat buildup/shut-offs, or moisture and lint around the dryer
• Supports a short, direct run to reduce kinks and airflow restrictions

• One 6-foot dryer vent duct

• Disconnect power; for gas models, turn off the gas supply before starting
• Pull the dryer forward and remove old ducting and lint/debris from connections
• Attach the duct fully to the dryer outlet and wall vent and secure with clamps; avoid sharp bends or crushing
• Move the dryer back carefully and confirm strong airflow at the exterior vent hood

This motor clip secures a motor to its mounting bracket or housing, keeping it aligned and stable during operation. Replacing a bent, broken, or missing clip helps stop rattling and prevents the motor from shifting. What it does:

• Retains the motor on its mounting bracket or frame
• Helps maintain alignment to reduce vibration and noise
• Prevents movement that can cause rubbing or wire strain
• Direct replacement when the original clip is damaged or missing

• One motor clip

• Disconnect power before servicing; allow all moving parts to stop
• Access the motor area, note the clip's orientation, and remove the damaged clip
• Seat the motor fully, then install the new clip to secure it to the bracket
• Inspect related mounts/grommets and wiring for wear; verify clearances before restoring power

This clip and insulator assembly secures and electrically isolates a component inside a range or wall oven. It keeps the part firmly positioned while preventing shorts and heat damage, supporting accurate, safe appliance operation.

• Holds the designated component against the oven liner or chassis
• Ceramic insulator provides electrical isolation in high-heat areas
• Maintains correct spacing and alignment for reliable performance
• Replaces a missing, bent, or heat-cracked clip/insulator to stop rattles or arcing

• Disconnect power; allow the appliance to cool fully before servicing
• Wear gloves and eye protection
• Access the mounting point; transfer the component into the new insulator and secure with the clip without pinching wires or capillary bulbs
• Restore power and verify proper operation

This drum baffle mounts inside the rotating drum to lift and tumble laundry during each cycle. Replacing a cracked, loose, or missing fin helps prevent snags and restores proper load movement. What it does:

• Lifts and turns items as the drum rotates to improve tumbling
• Separates garments to reduce tangling and keep loads moving evenly
• Helps prevent small items from lying flat against the drum surface
• Common symptoms include rattling or thumping, visible cracks, clothes snagging/tearing, and reduced tumbling

• One tall drum baffle

• Disconnect power; shut off gas supply before servicing
• Wear cut-resistant gloves; interior cabinet edges can be sharp
• Rotate the drum to access mounting points; support the drum while removing/installing the baffle
• Tighten fasteners securely; hand-turn the drum to verify clearance before testing

208 Volts

Size: 10-32 inch.

This adjustable buzzer kit replaces a failed or noisy mini buzzer to restore audible alerts for cycles, timers and notifications. Compact design lets the appliance signal you reliably when cycles finish or need attention. What it does:

• Produces audible tones for cycle end, timers and other appliance notifications
• Replaces buzzers that are silent, intermittent, weak or emitting erratic beeps
• Helps you hear and identify completed cycles and timed alerts
• Small, mountable unit that fits behind the control panel and connects to the control board

• One adjustable buzzer kit

• Disconnect power before servicing to avoid shock risk
• Access may require removing the control panel; keep fasteners organized for reassembly
• Disconnect the buzzer wiring harness or connector before removing the old unit; connect the new buzzer the same way
• Test buzzer function with power restored before fully reassembling

This electromechanical replacement timer restores timed cycle control for ovens, ranges and other Whirlpool appliances that use a mechanical timing mechanism. It provides reliable cycle advancement so settings run and finish as expected. What it does:

• Advances the appliance's timed cycles and signals control stages to start or stop heating/motor circuits
• Replaces a worn or non-running mechanical timer that no longer advances or keeps time
• Common symptoms fixed: timer knob won't turn, clock/timer doesn't run, cycles stop or fail to advance
• Works as the appliance's primary timing/control interface on compatible models

• One electromechanical timer assembly

• Disconnect power (unplug or switch off breaker) before removing the old timer to avoid shock
• Installation typically requires removing the control console or panel—handle trim and small parts carefully
• Avoid bending terminal tabs; ensure all wire connectors are fully seated

Specs: No.8X1/2 HEX WASHER HEAD

A replacement cycling thermostat that helps regulate dryer temperature and prevent overheating by cycling the heater on and off as needed. Restores temperature control for safer, more consistent drying. What it does

• Opens and closes to cycle the heating element, maintaining proper operating temperature.
• Helps prevent excessive heat build-up that can cause clothes damage or dryer shutdowns.
• Common fix for dryers that run too hot, have uneven drying, or won't maintain heat.
• Works with the dryer's existing temperature control system to stabilize cycles.

• One cycling thermostat

• Disconnect power before accessing or replacing the thermostat to avoid shock.
• This part mounts inside the dryer cabinet near the heating assembly.
• Handle the thermostat carefully and reconnect wires to the correct terminals.
• Test the dryer on a short cycle after install and monitor temperature; if symptoms persist, check other heating components.

Adjustable leveling feet that restore stability and balance to your appliance by letting you fine-tune height at each corner for a flat, wobble-free install—helps reduce vibration and improve door fit and operation. What it does:

• Provides adjustable height to level an appliance on uneven floors.
• Eliminates rocking or wobbling that can cause vibration, noise or movement during operation.
• Helps ensure doors and panels sit flush and seal properly.
• Durable replacement designed for direct fit where the OEM leveling foot is specified.

• Disconnect power and water before performing any work.
• Support the appliance so it cannot tip—use a jack or have a helper hold it while you adjust feet.
• Turn the foot to raise or lower the corner; use hand tools as needed and avoid excessive force.
• After adjusting, check stability and run a short cycle to ensure vibration and alignment are resolved.

A single pop rivet used to secure sheet-metal parts and small brackets on appliances for a permanent, vibration-resistant hold. Replaces missing or damaged rivets to restore proper attachment without welding. What it does:

• Provides a permanent blind-rivet fastening point for panels, brackets and trim.
• Replaces rivets that are sheared, loose or missing and prevents rattling or misalignment.
• Ideal where a solid, tamper-resistant join is required and screws aren't suitable.
• Works with a compatible pop-rivet tool for quick installation.

• Drill out the old rivet carefully; use the proper size hole for the replacement rivet.
• Use a dedicated pop-rivet tool and wear eye protection during installation.

Specs: 7/32 INCH

High limit thermostat, Canadian models only.