Dgg3042kfk Parts

This convection fan element mounts on the oven's rear wall around the blower. It supplies supplemental electric heat so the fan can circulate hot air evenly during convection modes for more consistent baking and roasting.

• Provides heat directly around the convection fan to help maintain even temperature during convection cycles
• Failure can cause poor browning, uneven results on multiple racks, or convection modes that run without proper heating
• May show visible breaks, blistering, or burnt spots; an open element will fail a continuity check
• If standard bake heats normally but convection bake does not, this element may be at fault

• Disconnect power at the breaker and allow the oven to cool completely before servicing
• Remove oven racks and the rear interior panel to access the element surrounding the fan
• Note wire positions; transfer any spacers or mounting hardware from the original element as needed
• Secure the element without bending it and confirm the fan spins freely with proper clearance

This door hinge is a direct-fit replacement part that supports and aligns an appliance door for smooth opening and secure closing. Replacing a worn hinge restores proper fit and prevents door sag, binding, or noisy operation. What it does:

• Provides the pivot point that lets the door open and close smoothly.
• Keeps the door aligned so seals meet and the door closes fully.
• Restores stable door movement and reduces sagging or rubbing.
• Helps stop binding, unusual noises, or doors that don't stay closed.

• Disconnect power to the appliance (and water supply if applicable) before starting work.
• Support the door while removing or installing the hinge to prevent damage or injury.
• Keep original screws and mounting hardware; new fasteners may be required if originals are worn.

This safety valve controls gas flow to the oven burner. When signaled by the igniter, it opens to allow ignition and helps maintain consistent heat, supporting safe, reliable preheating and baking performance.

• Regulates gas flow to the oven burner under control of the igniter and thermostat/electronic control
• Prevents gas from flowing until proper ignition conditions are met
• Common symptoms: oven won't ignite or heat, intermittent heating, extended preheat time, or weak/unstable flame
• Often inspected when the igniter glows but the burner does not light

• Disconnect power and shut off the gas supply before servicing
• Transfer any model-specific fittings or brackets from the original valve
• Use approved thread sealant on threaded connections; support tubing and avoid overtightening
• After installation, leak-check every connection with a soap-and-water or leak-detection solution

The Burner Grate is an OEM part for Frigidaire gas ranges. It supports racks and pans directly over the range's gas burners during cooking. The burner grate must withstand constant exposure to high heats without warping or degradation.

Causes of a bad burner grate include wear from heavy use over multiple years, corrosion from spills or food particles left on the grate, or cracks and chips that compromise durability and function.  

Symptoms of a bad burner grate are:

• Uneven or inefficient heat transfer to pots and pans during cooking  
• Warping or distortion of grate bars impacting pan support
• Sharp edges or breakage causing potential safety hazards

This OEM replacement grate is also compatible with some Electrolux, Crosley, and Amana gas ranges. 

This manifold supply tube routes gas from the appliance's inlet/regulator to the burner manifold and valves. Replacing a damaged tube helps restore safe, consistent fuel delivery and reliable burner performance. What it does

• Channels gas from the regulator/inlet to the burner manifold/valve assembly
• Maintains proper fuel flow to multiple burners
• Replace if the tube is bent, cracked, corroded, or leaking
• Symptoms can include multiple burners not lighting or weak/uneven flames due to restricted flow

• 1 manifold supply tube

• Shut off the gas supply and disconnect electrical power before servicing
• Note the routing and orientation of the original tube to match bends and connections
• Use only approved practices for your fitting type; do not apply sealant to flare-seat connections
• After installation, perform a soap-and-water leak test on all joints; do not operate if bubbles appear

This small replacement spacer positions and secures appliance components to maintain correct alignment and fit. Installing the spacer restores proper panel spacing and reduces vibration where a worn or missing spacer causes looseness or rubbing. What it does:

• Maintains the correct gap between panels, trim, or assemblies to ensure parts fit flush
• Keeps components aligned to prevent rubbing, binding, or uneven wear
• Helps reduce vibration and rattling caused by a missing or damaged spacer
• Preserves original part spacing for reliable operation of the surrounding components

• Disconnect power to the appliance before any service to avoid shock or injury
• Remove any trim or fasteners that block access; keep track of screws and small parts
• Match the new spacer's orientation to the original; do not force parts into place

Replacement screw that secures panels, trim and internal components in compatible appliances. Restores proper fit and helps reduce rattling or loose parts when the original fastener is missing, worn, or damaged. What it does:

• Fastens panels, brackets, trim pieces and small component assemblies to the appliance frame
• Helps eliminate noise and vibration caused by loose or missing fasteners
• Replaces stripped, corroded or missing screws to restore secure mounting
• Matches OEM fit when the identical screw is required for proper alignment

• Disconnect power to the appliance before starting any repair
• Use the correct driver size to avoid cam-out or damage to the screw head
• Do not overtighten; overtightening can strip threads or crack plastic parts

This cooktop grate provides a stable, elevated surface for pots and pans over the burner, restoring safe and even cookware support for gas ranges. Durable cast construction resists heat and helps keep burners accessible and level. What it does:

• Supports cookware above the burner for stable cooking and even heat exposure
• Keeps flames and burner caps accessible while protecting the cooktop surface
• Replaces cracked, warped, or missing grates that cause wobbling or uneven heating
• Helps maintain proper airflow around burners for consistent flame performance

• Allow the cooktop to cool completely before removing or installing the grate
• Lift the grate straight up to remove; seat it firmly on the cooktop supports when installing
• Clean with warm, soapy water; avoid harsh abrasives that can damage the finish
• Inspect grate for cracks or warping and replace if damaged to prevent instability

Replacement water inlet valve that controls water flow to the refrigerator's dispenser and ice maker, restoring proper filling and helping stop leaks. Use this valve to address fill and flow issues caused by a failed inlet valve. What it does:

• Opens and closes the water supply to the dispenser and ice maker so they fill correctly.
• Common symptom: no water dispensed or ice maker not filling.
• Common symptom: continuous water flow, visible leaks, or puddling under the refrigerator.
• Typically located where the household water line connects to the refrigerator; valve failures are a frequent source of water-related dispenser and ice problems.

• Disconnect power and shut off the water supply before starting any repair.
• Tighten fittings to the manufacturer's torque recommendations and check all connections for leaks after installation.

This glide restores smooth, aligned movement for a refrigerator or freezer drawer so the drawer opens and closes without sticking. Use it to replace a worn or broken glide and reduce scraping, binding, or uneven travel. What it does:

• Guides and supports the drawer so it tracks straight and slides smoothly.
• Replaces worn or damaged glides that cause drawers to stick, bind, or scrape.
• Helps prevent the drawer from coming off the track or shifting out of alignment.
• Reduces noise and uneven movement during opening and closing.

• Disconnect power (unplug the appliance) before servicing to avoid electrical hazards.
• Remove the drawer and any obstructing shelves per the OEM instructions to access the glide.
• Keep or replace original mounting screws; ensure the glide is oriented and seated correctly before tightening.
• Replace those parts to ensure a secure fit.

This insulation panel fits inside the refrigerator cabinet to help maintain consistent temperatures and reduce heat transfer. It preserves cooling efficiency and helps minimize frost and condensation when the appliance is operating properly. What it does:

• Provides thermal barrier between the cabinet and outer shell to help maintain internal temperature
• Helps reduce frost buildup and interior condensation when sealing and cooling systems are functioning
• Can improve energy efficiency by minimizing unwanted heat gain
• Dampens vibration and can reduce operating noise from the compressor area

• Disconnect power to the appliance before starting any repair to avoid electric shock
• Handle insulation carefully—avoid compressing or tearing the material to retain thermal performance
• Remove interior panels or shelving as needed to access the installation area; keep track of fasteners
• If the original insulation is damaged or contaminated, replace it and check nearby seals and gaskets for proper fit

This trim is a decorative finish piece for select ranges and wall ovens. It covers gaps and raw edges for a clean look and helps keep adjacent panels properly seated when the original becomes cracked, bent, or missing.

• Provides a finished appearance by covering exposed edges or gaps
• Helps maintain alignment of nearby panels or glass
• Replace if cracked, warped, missing, or no longer seats securely
• Common symptoms include loose/rattling panels and exposed or sharp edges

• Disconnect power; for gas models, also shut off the gas supply
• Wear gloves—edges can be sharp
• Remove old trim and transfer/reuse original screws or clips
• Align the new trim and secure with existing fasteners; confirm proper fit before reassembly

A replacement motor latch that secures the motor assembly to the appliance chassis, helping keep the motor stable during operation for smoother performance and reduced vibration. Fits specific Frigidaire/WCI motor assemblies. What it does:

• Secures and positions the motor assembly to prevent excessive movement
• Helps reduce vibration and rattling caused by a loose motor mount
• Restores proper alignment between motor and drive components
• Can eliminate intermittent contact-related noise from a shifting motor

• Disconnect power (unplug or switch off breaker) before starting any repair
• Installation typically requires accessing the motor area—expect to remove panels or the cabinet
• Keep track of mounting hardware; replace any damaged fasteners
• Test operation after reassembly; stop and recheck if noises or vibration persist

This ignitor orifice assembly is the replacement part that secures the ignitor and routes gas to the oven burner for reliable ignition. It restores proper ignition when the burner assembly is the source of the problem. What it does:

• Directs gas flow to the oven burner while holding the ignitor in the correct position
• Enables stable ignition so the oven can reach and maintain heat
• Commonly used when the oven fails to light, has intermittent ignition, or the burner won't stay lit
• Works as part of the oven's gas ignition system; replaces a worn or damaged orifice/ignitor mount

• One ignitor orifice assembly

• Turn off gas supply and electrical power before attempting service
• Inspect surrounding components (ignitor, valve, burner) and replace any damaged parts

This spring-loaded hinge supports and controls the oven door's movement so it opens smoothly and closes firmly, helping the door seal properly and retain heat. Replacing a worn hinge restores proper door alignment and closing force.

• Provides the pivot and spring tension for controlled door opening/closing
• Helps the door sit flush against the gasket to maintain a proper heat seal
• Common symptoms: door won't fully close, sags or drops, won't hold at a mid-open position, heat escaping from the front
• Typical causes of failure: metal fatigue, spring wear, or hinge deformation from heavy use

• Disconnect power; for gas models, also shut off gas. Allow the oven to cool completely.
• Support the door and engage hinge locks or remove the door.
• Springs are under tension—use gloves and eye protection; do not disassemble the hinge.
• Align with the receivers/slots and test for smooth operation and full closure; consider replacing both for even tension.

This wiring harness connects the appliance's electrical components to restore reliable power and signal routing. It replaces a damaged or worn harness to help resolve power loss and intermittent electrical issues. What it does:

• Transfers power and control signals between components so controls and motors can operate
• Replaces frayed, burned, or broken wiring that can cause intermittent operation
• Helps stop failures that lead to no-start or loss of specific functions
• Restores secure connector fit to reduce arcing or poor connections

• Always disconnect power before servicing the appliance
• Match connectors and wire routing to the original harness; avoid stretching or pinching wires
• Secure fasteners and strain reliefs; verify all connections are fully seated
• If you find heat or burn damage at terminals, inspect adjacent components for root cause