Du7800xs-3 Parts

For mating terminal use [AP31136300].

This push retainer is a small press-on fastener that secures components to shafts or studs inside your appliance. It restores a tight, reliable hold so knobs, trim, or linkages don't loosen or fall off during use. What it does:

• Presses onto a shaft or stud to secure knobs, trim, or linkages—no threads required
• Maintains spring tension to resist vibration during normal operation
• Replaces a missing, bent, or weakened retainer
• Common symptoms: loose or wobbly knobs/trim, parts slipping off, or a retainer that won't stay on

• 1 push retainer

• Disconnect power; for gas appliances, also shut off the gas supply
• Access the shaft/stud and carefully remove the old retainer with pliers; avoid damaging adjacent plastic parts
• Press the new retainer on squarely using a deep socket or nut driver; do not hammer directly
• If the mating shaft or component is damaged or deformed, address that before installing the new retainer

Color: White. Size: 13 oz. Spray paint primer. can.

This spring kit replaces worn or broken return springs in the applicable assembly, restoring proper tension and smooth movement so the mechanism operates reliably throughout the cycle and returns to its proper position. What it does:

• Provides the correct tension to move or hold parts in place
• Helps resolve weak return action, sticking, failure to engage/latch, or sagging components
• Can reduce noise caused by loose or fatigued springs
• Maintains consistent operation throughout the appliance's cycle

• Manufacturer-supplied spring kit

• Disconnect power; turn off water supply if applicable
• Springs are under tension—use eye protection and release carefully
• Note original spring routing and attachment points before removal
• Replace both for balanced operation

This small lever seal fits the dishwasher's detergent cup/dispenser. It seals around the lever/shaft to keep wash water out of the cup until the release cycle, helping deliver detergent at the right time for effective cleaning.

• Creates a watertight seal around the detergent cup lever/pivot
• Helps keep detergent dry until the main wash
• A worn or shrunken seal may allow early detergent washout or water in the cup before it opens
• Replacing the seal can help restore proper dispenser performance

• Disconnect power to the dishwasher before servicing
• Access the dispenser from the inner door; note lever and seal orientation
• Remove the old seal, clean the groove/shaft, and press the new seal fully into place
• Reassemble and run a short cycle to verify proper dispenser operation

This wheel leg is a replacement support used to stabilize and allow smooth movement of the appliance's lower assembly. It restores proper leveling and reduces wobble so the appliance sits securely and rolls or rests as designed. What it does

• Supports the appliance chassis at the lower corner and transfers load to the floor
• Helps maintain correct appliance height and leveling to reduce vibration and rocking
• Restores proper rolling or stationary support where a worn or broken leg caused instability
• Commonly replaced when the leg is cracked, stripped, missing, or no longer holds weight

• Verify appliance is unplugged and empty before accessing lower cabinet or base
• Support the appliance with a block or jack to prevent shifting while replacing the leg
• Remove any access panels or retaining hardware as needed; install the new leg in the original orientation
• Replace any fasteners that are damaged and test stability before returning the appliance to service

Size: 10-24 x 3/8 inch.

This seal kit is for the main tub. It goes around the pump housing.

Bottle with brush. Color: Platinum. Size: 0.6 fl.oz.

Screw for wash impeller.

This door spring retainer secures the dryer/washer door spring to the cabinet so the hinge spring stays in place for reliable door movement and alignment. It prevents the spring from slipping or disengaging during normal use. What it does:

• Holds the door spring end in the correct position so the hinge maintains proper tension
• Helps prevent door sagging, misalignment, or a door that won't stay closed
• Keeps the spring secured to reduce rattling or intermittent disengagement
• Works with the existing door hinge/spring assembly to restore reliable opening and closing

• Disconnect power (and gas if applicable) before any service; wear gloves and eye protection
• Access typically requires opening or removing the dryer/washer front or top panel; follow OEM service manual for steps
• Retaining springs are under tension—carefully release and re-seat springs to avoid sudden movement
• If other hinge or spring hardware is damaged, replace those parts to ensure safe operation

This dishwasher drain hose kit includes a clamp with instructions.