Du915 Wpq0 Parts

Size: 8-32 x .312 inch.

The Thermostat Clip is an OEM part for Whirlpool dishwashers. It plays an important supporting role by securely fastening the thermostat sensor inside the wash chamber. 

Symptoms of a faulty Thermostat Clip can include:

• Fluctuating or inconsistent water temperatures between cycles 
• Inability to properly detect temperature for desired heat levels
• Longer cycle times needed for reaching required temperatures
• Strange sounds or condensation around thermostat connection

Causes could arise from typical wear and tear stresses weakening plastic retaining clips. Exposure to harsh detergents may also erode clip material integrity over time.

This OEM replacement part is compatible with KitchenAid, Jenn-Air, Kenmore, and select Hotpoint and Roper dishwasher models as well. 

Size: 8-32 x 1/2 inch.

The Lower Dishwasher Rack Assembly is an OEM part for Whirlpool dishwashers. This part holds and organizes dishes, pots, and pans in the lower section of the dishwasher, ensuring they are properly positioned for effective cleaning.

Causes of a bad lower rack can include wear and tear from regular use, exposure to harsh detergents or high temperatures, and physical damage from heavy or improperly loaded items. 

Symptoms of a bad lower dishwasher rack assembly include:

• Rust or corrosion on the rack
• Broken or missing tines
• Difficulty sliding the rack in and out
• Poor arrangement of dishes, leading to ineffective cleaning

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This seal kit is for the main tub. It goes around the pump housing.

Notes: Only one screw hole is used now.

This inlet base seal is a gasket that fits between the inlet base and its mating surface. Replacing a worn seal helps maintain proper airflow through the inlet path and keeps spills and debris out of internal components.

• Forms a tight, continuous seal at the inlet base-to-housing joint
• Helps preserve correct airflow through the inlet path
• Blocks liquids, grease, and crumbs from leaking into the appliance interior
• Replace if the seal is cracked, flattened, brittle, loose, or you see visible gaps

• Disconnect power to the appliance before servicing
• Remove grates/cartridges, filters, or trim as needed to access the inlet base
• Clean and dry mating surfaces; install the new seal in the same orientation without stretching or twisting
• Reassemble and verify the seal sits evenly with no gaps

Screw for wash impeller.

A replacement mounting screw to secure appliance panels and components so parts stay properly fastened during normal use. Small but essential hardware for stable, rattle-free operation and reliable repairs. What it does:

• Fastens panels, brackets or components to the appliance chassis
• Prevents loose panels, vibration noise, or parts shifting during operation
• Used when original screw is lost, damaged, or stripped
• Restores proper fit and alignment after disassembly for service

• Disconnect power and water before starting any repair
• Use the correct screw type and length; do not force or substitute oversized fasteners
• Tighten until snug—avoid overtightening to prevent stripped threads or cracked parts
• Keep small parts away from children and pets

This timer knob replaces a worn or broken control knob and restores a clear, easy-to-grip timer control. The biscuit finish matches neutral appliance trims for a clean, factory look. What it does:

• Fits over the appliance timer shaft so you can set cook/dry cycles or timer functions
• Provides a tactile grip and clear pointer for accurate timer selection
• Replaces faded, cracked, or stripped knobs that no longer turn or stay engaged
• Matches biscuit-colored control panels for a seamless appearance

• One timer knob (biscuit)

• Remove power to the appliance before servicing to avoid injury
• Pull the old knob straight off the timer shaft; align the new knob's splines and press on until seated
• No wiring or tools typically required, but for model-specific instructions