Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Replace your dishwasher's rack holder rail if damaged, cracked, or broken. This structural component securely mounts the dish rack assembly in place.
Protects the base of your dishwasher from dust and debris while restoring a clean appearance. Replace if cracked, damaged, or missing. Verify fit.
Drives the rotating waterwall spray arm for proper cleaning coverage. Replace if belt breaks or dishwasher shows cleaning issues. Confirm fit with your model.
Myself Read more
Inlet drain hose connects your dishwasher pump to drainage system. Replace if cracked, leaking, or damaged to restore proper water drainage function.
Replaced bad hoses and clamps Read more
Detergent door won't open or close properly? This dishwasher dispenser slide ensures smooth detergent door operation. Simple DIY fix in under 30 minutes.
Front lower panel for dishwashers. Installs at the base of the door to cover the bottom section. Replace if cracked, broken, or missing.
Ordered replacement piece Read more
Ensures efficient drainage from your dishwasher to the sink or disposal. Replace if cracked, leaking, or clogged. Confirm fit with your model number.
Fix poor cleaning or standing water with this dishwasher food disposal unit. Grinds food particles to prevent clogs and improve wash performance.
Prevents leaks around the distributor shaft in your dishwasher's sump assembly. Replace if you see water pooling or error codes. Confirm fit by model.
Based on the apparent relation to draining that I found on the internet I decided to open/unscrew the areas under the bottom rack where the water is pumped out. One obvious issue I observed was the drain check valve was turned and not functioning. It appeared to be swollen and stretched. When the new "Vane-Check" valve arrived it was not swollen and fit perfectly. I assume heat swells it up over time. I replaced three other seals while I had it apart. The one under the chopping blade was... Read more
Dishes not getting clean? This water distribution duct nozzle directs water to upper spray arms. Connects pump assembly to spray levels for thorough cleaning.
Replaces cracked or missing door cap guide on your dishwasher. Installs on the door assembly to maintain alignment and smooth operation. Easy install.
Fix PE error code on your dishwasher with this half load synchronous motor. Simple 10-minute repair when dishwasher won't run due to component failure.
I went on line found the PE code and started troubleshooting. I ended up ordering a new circuit board, and the half-load motor and micro-switch. It turned out, I didn't need the circuit board. Replacing the motor and micro-switch solved the problem. The repair was very simple. I pulled out the dishwasher from under the counter, tipped it on its side and unscrewed the white plastic plate on the bottom. This exposed all the working parts of the dishwasher. Using the parts diagram on the... Read more
Dishwasher not filling with water? A faulty water inlet valve prevents water from entering during wash cycles. DIY-friendly repair in under an hour.
Myself. Correct part came quickly. Thanks Read more
Replaces broken, snapped, or worn dishwasher leveling legs. Installs at the base to stabilize and level your unit. Adjust height with pliers.
I removed the dishwasher, put it on its side, used a needle nose plier to remove the snapped piece of leg and screwed the new one in. Read more
Adjustable foot assembly for dishwasher leveling and height adjustment. Replaces missing, broken, or worn feet to stabilize your unit and reduce noise.
Using the parts, legs and the clamps that I ordered from appliancepaartspros.com arrived in time for quick installation. Someone suggested that I go back to the supplier for the parts and I felt that would be like finding a needle in the hay stack. The parts from appliancepartspros.com were just what was needed and the dishwasher is now installed and is working just great. Read more
Fix high temperature heating error codes on your dishwasher. This door seal sensor monitors water temperature. Simple DIY repair in under 1 hour.
This error code is for a high temperature heating error. Unplug the dishwasher or flip the circuit breaker that powers the dishwasher. Remove the dishwasher from under the counter. And remove the metal panel that is on the right side if you are looking at it from the front. It is 2 Phillips head screws. Using a flashlight, look at the very bottom of the pump housing and you will see the thermistor that you will need to replace. Unplug the connector from the thermistor then turn the thermistor... Read more