Dwcsr2070tww Parts

A replacement tension spring designed to restore proper movement and return force to the appliance mechanism. Helps the affected component operate smoothly so doors, levers or assemblies move with correct tension and alignment. What it does:

• Provides return and holding tension for the appliance mechanism to restore normal movement.
• Helps reduce sagging, misalignment, or loose operation of the associated door or linkage.
• Minimizes noise and vibration caused by a worn or weakened spring.
• Works as the direct-fit part when the listed part number matches your appliance.

• Disconnect power and water (if applicable) before beginning any repair.
• Springs are often under tension—wear eye protection and use caution when removing or installing.
• Follow the appliance's service manual or OEM instructions for correct orientation and safe installation.

This jump-up nozzle directs water flow inside the dishwasher to improve rinse and spray coverage. It replaces a worn, cracked, or clogged nozzle to restore proper water routing for consistent wash performance. What it does:

• Directs water upward from the spray arm/dispenser area for targeted rinsing
• Helps maintain even spray distribution across dishes
• May cause poor rinsing, spotting, or uneven cleaning when damaged or clogged
• Compatible with dishwasher models that use a jump-up style water nozzle

• One jump-up nozzle

• Designed for drop-in or snap-fit replacement; inspect surrounding seals and clips
• Turn power off and shut off water supply before beginning repair
• Use basic hand tools; avoid overtightening plastic fittings
• Replace only with the exact nozzle specified for your model

A replacement shaft seal that restores the watertight seal where a rotating shaft passes through the tub or housing, helping prevent leaks and protecting bearings and internal components from moisture and contamination. What it does:

• Seals the gap around a rotating shaft to stop water from leaking out of the tub or housing.
• Helps keep grease and contaminants contained around bearings and shaft openings.
• Common symptom link: replace when you see water on the floor, visible leaks near the shaft, or wet/soiled bearing areas.
• Small, inexpensive part that prevents further damage to nearby components when installed promptly.

• Disconnect power and turn off water supply before beginning work; drain remaining water from the appliance.
• Access usually requires partial disassembly (remove panels/tub or transmission as applicable); follow OEM instructions.
• Inspect shaft and housing for wear or damage; clean mating surfaces before installing the new seal.
• Test appliance for leaks after reassembly and before returning to regular use.

A replacement leveling leg that stabilizes your appliance and allows height adjustment for a secure, level install. Restores proper alignment to reduce rocking, vibration and uneven door gaps. What it does:

• Raises and levels the appliance so all feet contact the floor evenly.
• Stops rocking and excessive vibration that can cause noise or wear.
• Helps restore proper drainage and door alignment by correcting tilt.
• Matches original fit and function for reliable support.

• Disconnect power (and water for appliances with plumbing) before servicing.
• Raise or support the appliance safely before removing or adjusting legs.
• Turn the leg to raise or lower; make small adjustments and recheck level.
• Use common hand tools (wrench or pliers) and avoid forcing damaged threads.

Color: Stainless steel

A small replacement retainer clip used to secure exterior trim and interior panels on compatible Whirlpool appliances. Restores proper panel fit and prevents rattling or loose trim for a cleaner, safer operation. What it does

• Secures trim, panels or components in place to maintain proper alignment
• Helps stop rattling, vibration noise and loose-fitting parts
• Keeps seals and covers positioned so doors and panels close correctly
• Simple, single-purpose hardware used where a clip-style fastener is required

• One retainer clip as pictured

• Disconnect power (and water if applicable) before starting any repair
• Remove the surrounding trim or panel to access the retainer; small trim tools may help
• Fasten clip into the OEM mounting hole until it snaps or seats firmly
• Keep removed screws and small parts organized to avoid lost hardware

Color: Gray

Note: For faucet adapter

This is a machine screw used to secure appliance panels and components where an 8-32 thread fastener is specified. It provides a reliable hold for control panels, brackets, and interior assemblies. What it does:

• Fastens panels, brackets, and small components to the appliance chassis
• Holds control assemblies and trim pieces in place
• Maintains secure connections that prevent vibration-related loosening
• Works where an 8-32 coarse-thread machine screw of short length is required

• One 8-32 x 3/8" machine screw

• Use the correct driver (Phillips or slotted) to avoid stripping the head
• Thread into metal or nut/insert; do not overtighten to prevent thread damage
• Disconnect power and remove any panels as required for safe access

This drain impeller assembly circulates and ejects wash water through the washer's drain pump, restoring proper drainage and helping prevent standing water after a cycle. Durable design fits into the pump housing for reliable performance. What it does:

• Presses water through the pump housing to enable normal draining during drain/spin cycles
• Replaces worn or damaged impeller vanes that can cause slow or no draining
• Helps reduce noise and vibration from an imbalanced or broken impeller
• Restores proper water flow when the pump motor runs but little or no water is expelled

• Disconnect power and water supply before starting any repair
• Access requires removing the washer cabinet or pump housing depending on model
• Inspect pump housing and sealing surfaces for damage or debris before installing the new impeller
• Use common hand tools; tighten fasteners to OEM torque specs where provided