Dwd-Wd3011ww Parts

This control board housing secures and protects the washer's electronic control board, keeping circuitry stable and shielded from moisture and debris for reliable operation. It fits into the console area and supports proper control panel alignment. What it does:

• Holds and protects the electronic control board inside the console from impact, dust and moisture.
• Keeps the control board properly positioned for reliable electrical connections.
• Helps prevent control panel wobble or misalignment that can cause button or dial issues.
• Commonly replaced when housing is cracked, broken mounting tabs fail, or board access is needed.

• 1 control board housing

• Disconnect power and water to the appliance before beginning any repair.
• Handle the control board and housing carefully to avoid damage to connectors or circuit components.
• Use appropriate tools to remove console components; replace damaged mounting tabs and secure all fasteners.
• Discharge any capacitors and follow the board manufacturer's ESD/safety recommendations.

This chopper assembly replaces the food-chopping component in compatible countertop food processors, restoring even chopping and diced results. It helps get blades turning and keeps food processing performing as intended. What it does:

• Spins and chops food inside the processor bowl for consistent results
• Restores proper cutting when chopping is uneven or not happening
• Helps eliminate food buildup that causes noisy or inefficient operation
• Works with the existing drive coupling to transfer motor power to the blades

• Disconnect power and remove the processor bowl and lid before servicing
• Handle blades carefully — they are sharp; wear cut-resistant gloves
• Ensure the part seats fully on the drive coupling and locks into place before use
• Test operation with small amounts of food after reassembly; stop immediately if unusual noise or resistance occurs

This manifold mounting bracket secures the gas manifold assembly to the appliance frame, keeping fuel lines and related components aligned for reliable operation. It's a direct-fit replacement that restores proper manifold support. What it does:

• Holds the gas manifold in the correct position to prevent strain on connections and lines
• Helps maintain stable alignment of valves and supply tubing to reduce leaks and intermittent flow
• Addresses symptoms like a loose or rattling manifold assembly or visible bracket damage
• Restores proper mounting after impact or corrosion-related bracket failure

• One manifold mounting bracket

• Install only with the appliance powered off and gas supply completely shut; follow local codes
• Match bracket orientation to the original and secure with manufacturer-specified fasteners
• Inspect nearby tubing, fittings and valve mounts for damage when replacing the bracket

A filter guard that helps keep debris away from the wash pump and drain area, protecting the pump and improving drain performance. Simple replacement for worn or damaged filter housings. What it does:

• Covers and protects the dishwasher's lower filter area to help prevent large debris from entering the pump
• Helps reduce clogs and poor drain performance caused by food or loose items
• Maintains proper water flow through the filter assembly for more reliable operation
• Works as a replacement for a cracked, warped, or missing filter guard that leaks or allows debris through

• Disconnect power to the appliance before any service to avoid shock or injury
• Remove the lower rack and existing filter assembly to access the guard
• Inspect adjacent filter parts for wear; replace damaged components to ensure proper sealing
• Hand-tighten or seat parts as directed by the OEM; avoid forcing or overtightening plastic components

A stainless pushnut used to secure shafts, studs, or small components with a quick, push-on retainer that resists corrosion. Keeps parts fastened without threading or additional hardware for a clean, low-profile fit. What it does:

• Acts as a push-on retaining nut to hold shafts, studs, or fittings in place
• Provides a corrosion-resistant stainless finish for wet or high-humidity areas
• Prevents components from sliding off axles or posts during normal operation
• Commonly used on control shafts, knobs, or small internal assemblies

• Turn power off and unplug appliance before servicing to avoid shock or injury
• Push onto the post or shaft until fully seated; a firm press or light tap may be required
• Use appropriate hand tools or pliers with protection to avoid damaging the part
• Replace with identical part number to ensure fit and function

Back

This main manifold assembly routes fluids through the appliance to enable proper operation of the system. Replaces a worn or damaged manifold to help restore correct flow and reduce leaks or performance issues. What it does:

• Directs and distributes fluid or gas to multiple outlets inside the appliance
• Helps maintain consistent delivery to valves, burners or spray arms
• Failing manifolds can cause leaks, weak or no flow, or error codes related to supply issues
• Designed to work with the appliance's factory plumbing and mounting points

• One main manifold assembly as shown

• Disconnect power and shut off water or gas supply before beginning work
• Inspect associated seals, gaskets and fittings; replace any damaged components to prevent leaks
• Test for proper operation and leaks after installation

Size: 1-3/8``

This miscellaneous parts package contains assorted small replacement parts commonly used for minor appliance repairs and upkeep. It provides a convenient set of replacement pieces to help restore secure fit and basic function. What it does:

• Supplies assorted small components used to replace lost or worn fasteners, clips, and trim pieces
• Helps restore proper fit and alignment of panels, drawers, and small assemblies
• Useful for quick maintenance tasks and keeping appliances functioning between major repairs
• Reduces downtime by providing commonly-needed small parts on hand

• Disconnect power and, if applicable, water before starting any repair
• Use the correct replacement piece for each location;
• Keep small parts away from children and pets; handle sharp fasteners with care
• Refer to your appliance's model-specific service instructions for proper installation

This dishwasher door spring provides the counterbalance tension that lets the door open and close smoothly. Replacing a worn or broken spring restores proper door feel and helps prevent the door from dropping unexpectedly.

• Provides counterbalance tension so the door opens and closes smoothly
• Helps the door stay partially open without drifting
• Reduces slamming or sudden drop when opening
• Common failure signs: door feels heavy, drops quickly, opens unevenly, or a spring is visibly broken

• Disconnect power and shut off water; remove the toe-kick/access panel
• Support the door; note spring routing and which frame holes are used before removal
• Install the new spring in the same holes; adjust hole selection only per service information to fine-tune tension
• Springs are under tension—wear gloves/eye protection; consider replacing both springs together for balanced operation

Note: New rack no longer includes removable tines or cup shelf. This part is a lower dishrack. The lower dishrack is the lower shelf of a dishwasher that holds plates, bowls, and utensils. To remove the old dishrack, simply pull it out and lift the wheels up from its track. Set it off the side, and lift the new dishrack. Slide it into its track and make sure it is locked in. If it is gliding in and out in a smooth way, it has been installed properly.This genuine replacement OEM part is sold individually and is compatible with Whirlpool brands include Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Sears/Kenmore brand appliances.