Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Fix melted plastic or goop marks on clothes with a new dryer heat diffuser. Replaces damaged diffuser that causes staining. DIY repair with 3 screws.
Removed 3 screws which required a torx bit. Used small headless nails to line up the holes and use as a guide for sliding on new diffuser. Put screws in one at a time and tightened down. rotating the drum helped with slight mis-alignement with the screw holes. Read more
Dryer not heating or overheating? This safety thermostat (hi-limit L210) cuts power when temps get too high. DIY-friendly, 10-minute install with video.
Replaced the high limit safety thermostat. Ordering was easy, and the part came quickly. The video on the web site was helpful, although I was not able to follow the instructions fully. Unless you have super skinny, long arms, you cannot reach under and around the dryer tub to reach the belt tension arm. I ended up having to remove the side panel of the dryer to remove the belt from the motor. Replacing the thermostat was simple enough. At this point, it seems to have corrected the... Read more
Fix a dryer that won't advance, runs continuously, or stops unexpectedly. This timer controls cycle progression and power routing. 15-minute DIY repair.
Just as the folks in the comments section said, I tested everything to make sure the timer had power which it did. I then tested with the OHM tester and saw that the switch was open when the timer was set to any drying cycle. So i changed the timer and voila! timer is functioning again. It was a very easy fix. Just pop the four screws out of the back of my timer panel on the dryer, detach all the wires, lift up on the little bracket that is holding the timer in place and twist it, and it... Read more
Replacement drum baffle installs inside your dryer to lift and tumble clothes during drying. Replace if cracked, broken, or mounting holes are stripped out.
I ordered two new baffles and 7 screws. I also ordered 6 large washers. We were running with one baffle held by only 2 of 3 screws. It appears that a repairman in the past had removed the large washers and over time, the screw heads reamed out the hole, causing the baffles to detach and break. In about 15 minutes, I was able to tighten up the existing baffle and add the two new ones. I also added the 6 big washers to help strengthen this to prevent future issues. I no longer have to listen to... Read more
Reversible door plug fills unused mounting holes when switching refrigerator door swing direction. Replaces broken or missing plugs for a finished look.
Replacement screw secures dryer panels, brackets, and internal components. Replace stripped, lost, or damaged screws to eliminate rattles and maintain assembly.
Supports the idler pulley to maintain proper belt tension in your dryer. Replace if the arm is warped, cracked, or causing belt tracking issues.
After replacing the belt less than a year ago, when it broke again we started to think something may be going on with the idler pulley. Ordered a new belt and pulley wheel, only to have the belt break again the very next day. After a call to customer service explaining the situation, they replaced the belt and pulley wheel which were both under warranty, and suggested replacing the arm itself. We also had to replace the interlock switch. Parts arrived quickly. The repair itself took about an... Read more
Protective cover that shields the rear power connection terminals on your dryer. Replace if cracked, broken, or missing to prevent lint buildup and accidental contact with electrical connections.
About 45 minutes only because the actual line in the circuit breaker box was loose. It was nice because all the parts needed were suggested. The video was a great help. Thanks. Read more
Secures the dryer drum to the rear bearing assembly. Replace if missing, stripped, or damaged to properly mount and stabilize the drum during operation.
Replaced the screw Read more
Fix a dryer that overheats or won't heat properly with a new temperature switch. Controls heat settings across multiple cycles. DIY-friendly repair.
Seals the blower-to-exhaust duct connection in your dryer. Replace if torn, brittle, or causing heat loss and longer dry times. Confirm fit by model.
Found information on your website and parts to fix the problems. Videos were extremely helpful and made the repairs very quick and easy. Dryer quiet now and runs like new. Read more
Replacement door hinge that supports and pivots your dryer door for smooth opening and closing. Install when original hinge is bent, worn, or broken.
White cover panel that installs on top of your dryer cabinet. Replace if cracked, rusted, loose, or missing to restore a clean appearance.
I watched a YouTube video how to remove the top of my dryer cover. It just required removing a few screws. Read more
Adjustable leveling leg that installs on the bottom of your dryer to stabilize and level the unit. Replace missing, broken, or worn legs. Easy DIY.
Went to a local appliance store to purchase these legs. Their price was very high and shipping from their supplier was 5 business days to their store. I placed an order with Appliance Parts Pros on Dec 16 after 3pm and received my order at my home in less than 24 hours. Great service. Read more
Replacement screw for securing dryer components like drum supports, panels, and housings. Needed when screws are lost, stripped, or damaged during repair.
Started by replacing the belt - which was easy to do following the APP video on YouTube. Quickly learned that wasn't the problem. Took the dryer apart again and found that the issue was the glides were completely worn down on the bearing. Looked to replace just those, but saw the bearing was too worn to hold them, so got a new one as well (and a new screw as I dropped one and didn't want to take even more of the dryer apart!). Installing new glides (you need 4 of these with a new bearing) and... Read more
Rear leveling leg and bracket assembly for dryers. Replaces damaged, broken, or missing legs. Ensures proper dryer stability and level positioning.
Bought foot and put it on dryer Read more