Dwu8460aax Maytag Parts

A replacement tension spring designed to restore proper movement and return force to the appliance mechanism. Helps the affected component operate smoothly so doors, levers or assemblies move with correct tension and alignment. What it does:

• Provides return and holding tension for the appliance mechanism to restore normal movement.
• Helps reduce sagging, misalignment, or loose operation of the associated door or linkage.
• Minimizes noise and vibration caused by a worn or weakened spring.
• Works as the direct-fit part when the listed part number matches your appliance.

• Disconnect power and water (if applicable) before beginning any repair.
• Springs are often under tension—wear eye protection and use caution when removing or installing.
• Follow the appliance's service manual or OEM instructions for correct orientation and safe installation.

This drain hose routes and removes wastewater from the appliance so it can pump out normally and avoid standing water. It's a direct-fit service part used to restore proper draining. What it does

• Carries wastewater from the appliance pump to the household drain or air gap
• Restores normal draining when original hose is cracked, split, or leaking
• Helps prevent water backing up into the appliance when properly routed and secured
• Can stop intermittent leaks or reduced drain performance caused by hose damage

• One drain hose

• Disconnect power and turn off water supply before starting any repair
• Inspect hose routing and replace with the same path to avoid kinks or high loops that trap water
• Secure hose connections with appropriate clamps; tighten but avoid over-torquing
• After installation, run a short drain cycle and check all connections for leaks

A replacement leveling leg that stabilizes your appliance and allows height adjustment for a secure, level install. Restores proper alignment to reduce rocking, vibration and uneven door gaps. What it does:

• Raises and levels the appliance so all feet contact the floor evenly.
• Stops rocking and excessive vibration that can cause noise or wear.
• Helps restore proper drainage and door alignment by correcting tilt.
• Matches original fit and function for reliable support.

• Disconnect power (and water for appliances with plumbing) before servicing.
• Raise or support the appliance safely before removing or adjusting legs.
• Turn the leg to raise or lower; make small adjustments and recheck level.
• Use common hand tools (wrench or pliers) and avoid forcing damaged threads.

This is a machine screw used to secure appliance panels and components where an 8-32 thread fastener is specified. It provides a reliable hold for control panels, brackets, and interior assemblies. What it does:

• Fastens panels, brackets, and small components to the appliance chassis
• Holds control assemblies and trim pieces in place
• Maintains secure connections that prevent vibration-related loosening
• Works where an 8-32 coarse-thread machine screw of short length is required

• One 8-32 x 3/8" machine screw

• Use the correct driver (Phillips or slotted) to avoid stripping the head
• Thread into metal or nut/insert; do not overtighten to prevent thread damage
• Disconnect power and remove any panels as required for safe access

This drain impeller assembly circulates and ejects wash water through the washer's drain pump, restoring proper drainage and helping prevent standing water after a cycle. Durable design fits into the pump housing for reliable performance. What it does:

• Presses water through the pump housing to enable normal draining during drain/spin cycles
• Replaces worn or damaged impeller vanes that can cause slow or no draining
• Helps reduce noise and vibration from an imbalanced or broken impeller
• Restores proper water flow when the pump motor runs but little or no water is expelled

• Disconnect power and water supply before starting any repair
• Access requires removing the washer cabinet or pump housing depending on model
• Inspect pump housing and sealing surfaces for damage or debris before installing the new impeller
• Use common hand tools; tighten fasteners to OEM torque specs where provided

This replacement rack track restores smooth, stable rack movement and keeps the oven rack aligned while sliding in and out. It helps prevent rack sagging, binding, or uneven travel so food and cookware stay level and secure. What it does

• Guides and supports the oven rack so it slides in and out smoothly.
• Prevents racks from sagging, tipping, or binding when pulled forward.
• Restores proper rack alignment to reduce scraping, catching, or loud banging.
• Works with standard oven/range racks that use a molded metal/plastic track system.

• High-level swap: remove the oven racks, unfasten the old track, and secure the replacement in the same mounting locations.
• Use appropriate hand tools and avoid forcing parts; aligning the track before tightening fasteners reduces binding.
• Disconnect power to the appliance or follow the manufacturer's safety guidance if servicing components near electrical connections.

This snap-in outlet connector secures wiring to an appliance control or harness and restores a reliable electrical contact. Designed for a direct, tool-assisted snap fit, it helps eliminate loose or intermittent connections. What it does:

• Provides a secure snap-in electrical connection between wiring and the appliance harness or control
• Restores power flow when a worn or damaged outlet causes intermittent operation or no power
• Prevents arcing and poor contact that can result from loose terminals
• Matches OEM fit for straightforward replacement when the original snap outlet is broken or missing

• Disconnect power to the appliance before inspecting or replacing electrical parts
• Remove access panels as required to reach the outlet; replacement typically snaps into place
• Verify correct orientation and full seating of the connector to ensure a solid contact
• If corrosion or wiring damage is present, replace or repair wiring per OEM guidance

This door insulation panel fills the oven/dryer door cavity to help contain heat and improve energy performance while reducing noise and hot spots. It's a direct-fit replacement designed to restore proper door thermal resistance. What it does:

• Replaces damaged or missing door insulation to help reduce heat loss from the appliance door
• Helps minimize vibration and rattling noise caused by loose or compressed insulation
• Restores proper clearance between the door inner and outer panels to prevent hot spots
• Supports consistent cooking/drying temperatures by improving door thermal sealing

• Disconnect power (and gas, if applicable) before beginning service.
• Door disassembly is typically required; follow for safe removal and reassembly.
• Handle insulation and any sheet metal carefully to avoid cuts; wear gloves and eye protection.
• Only install the exact part indicated for your model; do not compress or modify the insulation.

This rinse aid reservoir holds and dispenses rinse aid into the dishwasher's final rinse cycle to help reduce spotting and improve drying performance. Replaces a worn or cracked reservoir to restore proper rinse-aid delivery. What it does:

• Stores rinse aid and meters it into the final rinse to improve sheet-drying and reduce water spots
• Helps prevent streaking and film on glassware caused by inadequate rinse-aid distribution
• Stops leaks or overflow that can occur from cracked or damaged reservoirs
• Works with the dishwasher's dispenser assembly to deliver the correct amount each cycle

• Disconnect power to the appliance before beginning any work.
• Access typically requires removing the inner door panel; handle panels and fasteners carefully.
• Inspect mounting clips and seals; replace damaged hardware to prevent leaks.
• Refill with manufacturer-recommended rinse aid only; run a short cycle to ensure proper operation and no leaks.

Color: Black