Ei23bc35ks Parts

This defrost thermostat controls power to the defrost heater by sensing the evaporator's temperature. Replacing a failed thermostat helps stop heavy frost build-up and supports consistent cooling and airflow in your refrigerator and freezer.

• Monitors evaporator coil temperature during the defrost cycle
• Opens to shut off the defrost heater at a safe temperature; closes again when cold to allow the next defrost
• Failure symptoms can include heavy frost/ice on the back wall or evaporator
• May lead to reduced airflow, poor cooling, or the fresh food section warming after several days

• Disconnect power before servicing; wear cut-resistant gloves
• Access by removing the freezer's rear panel to reach the evaporator area; defrost any heavy ice to avoid damage
• Position the thermostat in the same spot on the evaporator tubing; ensure firm contact and route wiring as originally secured, away from sharp edges and the heater
• Reassemble panels, restore power, and observe for proper defrosting over the next cycles

The Adjustable Foot is an OEM part for Frigidaire dryers. This part is located at the bottom of the dryer and allows you to level it, ensuring stability and proper operation. 

Causes of a bad adjustable foot can include regular wear and tear, damage from moving the appliance, or breaking due to excessive weight or stress.  

Symptoms of a bad adjustable foot include:

• The dryer wobbling or tilting
• Difficulty in adjusting the height of the foot
• Visible damage or deformation of the foot
• Unusual noises or vibrations during operation

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Defrost Thermostat is an OEM replacement part for Frigidaire upright freezers. It is a temperature-sensing device that monitors coil temperatures, triggering the automatic defrost cycle to safely melt frost buildup obstructing airflow. Located near refrigerator coils, the defrost thermostat optimizes energy-efficient defrosting.

Causes often relate to regular exposure to fluctuating interior freezer temperatures over extended periods. Impacts compromising calibration can also force early replacement.

Symptoms involve:

• Excessive ice accumulation hinders air circulation and cooling power
• The inability of the unit to maintain a frost-free interior environment
• Higher utility costs from the refrigerator constantly fight accumulation

This Frigidaire OEM replacement part fits upright models by Electrolux, Gibson, and some Kenmore models.

Nylon

This compressor inverter control board powers and regulates the variable-speed compressor in your refrigerator by converting household AC into the controlled output the compressor needs. Replacing a failed inverter can restore compressor operation and normal cooling performance.

• Receives commands from the main control to vary compressor speed for efficient, steady cooling
• Converts AC line voltage to the controlled output required by the compressor motor
• Common symptoms of failure: refrigerator warm, compressor not running while fans/lights operate
• May also present as intermittent cooling, clicking or humming near the compressor, or visible damage on the module

• Disconnect power before servicing; this is a high-voltage component mounted at the compressor
• Note wire positions and transfer connectors one at a time; ensure all connections are fully seated
• Secure the module to the original mounting to maintain proper heat dissipation and vibration control

This cover assembly replaces a damaged or missing cover on your appliance, protecting internal components and restoring a clean, finished appearance. Use it when the original is cracked, loose, or no longer secures properly.

• Shields internal parts from debris, spills, and accidental contact
• Helps keep components enclosed and aligned for reliable operation
• Restores the appliance's finished look after damage or wear
• Common signs of failure: cracks, broken or missing tabs, discoloration, rattling, or a cover that won't stay in place

• Disconnect power before servicing; shut off water supply if working near water connections
• Remove retaining screws or release tabs; note the orientation of the original cover
• Transfer and reuse original screws, clips, or seals if required
• Do not overtighten fasteners into plastic; ensure all tabs fully engage before testing

This replacement guide aligns and supports a moving component so it travels on its intended path without binding. Replacing a worn or broken guide restores smooth operation and helps prevent scraping, jamming, or premature wear of connected parts.

• Keeps the associated rack, drawer, or panel centered and properly aligned during movement
• Provides a track/stop for the mating part to follow
• Reduces friction and noise for smoother sliding
• Typical failure signs: sticking, uneven travel, scraping noises, or visible cracks/broken tabs

• Disconnect power; also shut off water or gas
• Remove the associated assembly to access the guide and note its orientation
• Reuse original screws/clips and tighten securely without overtightening
• Test movement after installation; replace worn mating rails or rollers if needed

This is the vertical flipper mullion assembly that mounts to one fresh-food door and pivots closed to seal the center gap when both refrigerator doors are shut, helping maintain proper temperature and energy efficiency.

• Creates the center seal between French-door refrigerator doors
• Helps prevent warm air infiltration and moisture/condensation in the fresh-food section
• Common failure signs include a loose or broken hinge, mullion not staying aligned, condensation at the door center, or doors not sealing properly
• May also be noted if doors pop open or temperature fluctuates in the refrigerator compartment

• Unplug the refrigerator before servicing
• Remove door bins to access mounting screws/clips
• Transfer any original covers or hardware if not part of the new assembly
• Verify proper hinge engagement so the mullion flips and seals smoothly before restoring power

This freezer air duct directs cold air from the evaporator fan through the freezer compartment, helping maintain steady temperatures and airflow. Replace a cracked, warped, or missing duct to restore consistent cooling and reduce frost or noise. What it does:

• Channels air from the evaporator fan outlet to the freezer vents for even cooling
• Helps maintain targeted freezer temperature and proper circulation
• A damaged or loose duct may contribute to weak airflow, frost buildup near vents, temperature swings, or rattling noises
• Seals the airflow path when properly seated to minimize leaks and hotspots

• 1 freezer air duct

• Disconnect power to the refrigerator before servicing
• Clear the freezer and remove any panels, shelves, or the ice bin as needed for access
• Remove mounting screws or clips, note seal orientation, and seat the new duct fully
• Reuse original hardware, restore power, and verify airflow from the vents

This replacement screw secures refrigerator components such as brackets, trims, and covers. Replace missing or stripped hardware to keep parts tight and aligned, helping eliminate rattles and restoring a solid, reliable fit.

• Fastens interior or exterior components to the cabinet or doors
• Replaces missing, rusty, or stripped hardware
• Helps reduce vibration noises from loose parts
• Restores proper fit and alignment of panels, trims, or covers

• Disconnect power; turn off water supply if working near the dispenser or ice system
• Retain and reuse any original spacers or washers
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Replace one fastener at a time to maintain alignment

This is the drive gear for the ice maker module. It transfers motor power to the ejector/harvest mechanism so cubes release consistently; worn or stripped teeth can cause clicking, stalls, or little to no ice production.

• Transfers motor torque to rotate the ejector and complete the harvest cycle
• Replaces a cracked, stripped, or worn gear that prevents proper ice ejection
• Typical symptoms: no ice production, icemaker stuck mid-cycle, clicking or grinding from the module
• Helps restore reliable ice maker cycling

• Unplug the refrigerator before service; turn off the water supply if moving the icemaker
• Remove the icemaker assembly for access; note the original gear's orientation before removal
• Align the new gear with the shaft; do not force it—inspect mating parts for wear
• After reassembly, verify the ejector turns freely; restore power and run a test cycle

This replacement part is a set screw, and it is intended for use in different types of appliances. This is a genuine replacement part made by Frigidaire. This screw set is compatible in many different areas of the appliance. Screws are typically used for keeping parts of the machinery secure and in place. It is possible that screws can become loose over time and need to be replaced. A new screw set might be needed if the user notices parts of the appliances are becoming loose or are falling off. This can be due to screws becoming stripped over time or if the appliance is bumped during transport. It is typically easy to replace screws. Simply remove the old screw and replace it with a new part. The only tools needed for this repair are a screwdriver and possibly pliers if the damaged screw is stuck in place.Note that this is a genuine OEM replacement part and is sourced from the manufacturer. This set screw is sold individually.

This thermistor is a temperature-sensing resistor that monitors internal temperature and reports it to the control. Replacing a faulty sensor restores accurate temperature feedback for proper operation and consistent, reliable cycle performance. What it does:

• Continuously measures temperature and changes resistance for the control to read
• Helps regulate heating/cooling and overall cycle timing
• Supports safety logic that prevents improper temperatures
• Failure may cause inaccurate temperatures, long/short cycles, or temperature-related error codes

• 1 thermistor

• Disconnect power before servicing; shut off water or gas if applicable
• Access the sensor, note wire routing/orientation, and transfer any existing clip or seal as needed
• Make secure electrical connections and route wires away from hot or moving parts
• Many appliances use multiple sensors—diagnose with an ohm/diagnostic test before replacement, then run a test cycle after install

This door bin guard secures items on a refrigerator door shelf, preventing bottles and containers from sliding out. Replace it when cracked or missing to restore safe, usable door storage. What it does:

• Mounts to the front of a door bin to hold contents in place
• Replaces a broken, warped, or missing guard
• Helps resolve issues like items falling from the door shelf or a loose/broken bar
• Restores usable door storage space

• 1 door bin guard

• Unplug the appliance or disconnect power before servicing
• Empty the affected bin; release the old guard and align/snap the new guard into the slots
• Let cold plastic warm to room temperature before installation to reduce the risk of cracking
• The guard is fully seated before reloading items

This mullion assembly forms the front center divider of the refrigerator and includes an integrated anti-sweat heater. It helps keep the area where the door gaskets meet dry, supporting a clean look and a reliable, moisture-free seal.

• Provides the rigid center divider that the door gaskets seal against
• Built-in heater warms the divider to reduce sweating/condensation in humid conditions
• Helps limit air leaks that can lead to moisture, frost, or temperature fluctuations
• Common signs of trouble: persistent condensation on the center divider, visible cracks/warping, or poor gasket contact along the center

• Disconnect power to the refrigerator before servicing; wear cut-resistant gloves
• Remove mounting fasteners, carefully release the assembly, and disconnect the wire harness (note routing/orientation)
• Position the new assembly, reconnect the harness securely, and reinstall fasteners without overtightening
• Verify doors close smoothly and gaskets contact evenly along the divider before restoring power

This #10-32 x 3/4-inch machine screw secures appliance components such as panels, brackets, and handles. Using the correct length and thread helps restore a snug, rattle-free hold wherever this screw is specified by the manufacturer.

• Fastens components with a #10-32 machine thread and 3/4-inch length
• Helps keep panels, trim, brackets, or handles secured and aligned
• Replaces missing, stripped, or corroded hardware
• Common signs include loose or wobbly parts, rattling, missing screws, or damaged screw heads/threads

• Disconnect power before servicing; if working near a water connection, shut off the water supply
• Use the correct driver/bit and start threads by hand to avoid cross-threading
• Tighten snugly; do not overtighten to prevent stripping plastic or threads
• Reuse any model-specific washers or spacers if present