Eied50liw Parts

This idler spring attaches to the idler arm to keep the drive belt properly tensioned, preventing slip and chatter. Replacing a weak or broken spring restores steady rotation and helps reduce noise and belt wear.

• Maintains correct belt tension by pulling the idler arm into position
• Helps prevent belt slippage, squealing/chirping, and premature belt wear
• A failed spring can cause no or intermittent rotation and the belt coming off
• Typical signs include a loose belt, off-track belt, or rhythmic squeak from the base

• Disconnect power before servicing; if working on a gas appliance, shut off the gas supply
• Access the idler assembly; note belt routing before removal
• Relieve belt tension, then move the idler arm to remove and replace the spring on the same mounting holes
• After reassembly, rotate by hand to verify smooth belt tracking before test

This vane screw secures the internal drum baffle (vane) to the drum, keeping loads turning properly and preventing rattles or snags. Replace a missing or stripped screw to restore a tight, stable baffle during cycles.

• Fastens the drum baffle/lifter (vane) to the rotating drum
• Helps maintain proper tumble and load turnover
• Common symptoms: loose or wobbly baffle, rattling or clunking noises, items catching on a raised baffle edge, or a baffle that detaches
• Visual cues: missing screw or stripped/damaged threads at the baffle mounting holes

• Disconnect power before servicing; shut off gas
• Access the baffle from inside the drum; align holes and start the screw by hand to avoid cross-threading
• Tighten firmly but do not overtighten to prevent stripping the drum or cracking the baffle
• Start all screws before final tightening to seat the baffle evenly

This line noise filter conditions incoming AC power by reducing electromagnetic interference before it reaches the appliance's electronics. Replacing a shorted or damaged filter can restore stable operation and help prevent erratic control behavior.

• Filters EMI/RFI on the power line before it reaches the control system
• Helps protect sensitive electronics from interference and voltage spikes
• Failure may present as no power, intermittent resets, or nuisance GFCI/breaker trips
• Typically mounted near the power-cord entry; also called a line filter

• Disconnect power and allow any capacitors to discharge before servicing
• Note wire positions and line vs. load orientation; take a photo before removal
• Secure the ground and mount the new filter firmly to the chassis
• Route and reconnect wires carefully to avoid pinching; reassemble and test

This dryer blower moves air through the drum, lint filter, and exhaust so laundry dries efficiently. Replacing a damaged blower restores proper airflow and helps prevent long dry times and overheating issues.

• Draws and circulates air across the heater, through the drum and lint filter, and out the vent
• Maintains correct airflow and temperature control for consistent drying performance
• Worn, cracked, or clogged blowers may cause weak exhaust airflow and extended dry cycles
• May also present as rattling/grinding noises from the blower area or high-heat shutoffs

• Disconnect power; if gas, turn off gas supply before servicing
• Access the blower by removing the front/lower panel and blower cover
• Clean lint/debris from the housing and duct; transfer any seals or hardware from the original as needed
• After installation, spin the blower by hand to verify free movement; reassemble and test airflow

Replace a failed thermistor with this factory temperature sensor. It monitors temperature and feeds that data to the control, helping the appliance regulate heat and run cycles correctly. A faulty sensor can cause temperature-related performance issues.

• Senses temperature and sends a resistance signal to the control board for regulation
• Helps maintain proper heating/temperature during operation
• Failure may cause no heat or overheating, erratic or extended cycles, or temperature/sensor error codes
• Replace when sensor is open/shorted or readings are out of range per service diagnostics

• Disconnect power before servicing; if applicable, also shut off water or gas supply
• Access the sensor, unplug the wire connector, and remove any mounting screw/clip
• Install the new sensor; transfer any bracket/seal from the original and route wiring away from hot or moving parts
• Run a diagnostic or test cycle after replacement to confirm normal operation

The Motor Mounting Clamp is an OEM part for Frigidaire dryers. This clamp secures the motor in place within the dryer, ensuring it operates smoothly and remains stable during the drying cycles. The motor mounting clamp is essential for maintaining the proper alignment and function of the dryer motor.

Over time, the motor mounting clamp can become worn out or damaged due to constant vibration and movement. Accidental impacts or mishandling during maintenance can also cause the clamp to fail, leading to motor misalignment or instability.

Symptoms of a bad motor mounting clamp include:

• Excessive noise or vibration during the drying cycle
• Motor shifting or moving within the dryer
• Reduced drying efficiency
• The dryer not starting or stopping abruptly

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This moisture sensor monitors dampness inside the dryer drum and signals the control when fabrics are dry, helping automatic cycles end on time and avoid overdrying. Replacing a failed sensor can restore consistent Auto Dry performance and cycle times. What it does:

• Detects moisture level via conductivity across the sensor surfaces inside the drum
• Sends feedback to the control so Auto Dry cycles advance and stop correctly
• Helps prevent overdrying and underdrying in sensor-based cycles
• Common symptoms of a faulty sensor may include: auto cycles ending too soon or running too long, clothes remaining damp, or the dryer staying on "Sensing" while timed cycles still work

• 1 moisture sensor

• Disconnect power and, if applicable, shut off gas before servicing
• Access the sensor at the front bulkhead/lint housing area; remove front panel as needed per model
• Transfer connectors and route wiring exactly as original; secure the sensor firmly
• Clean the sensor contact surfaces with rubbing alcohol; residue from dryer sheets or fabric softeners can affect readings

This metric machine screw features an M5 x 0.8 thread used to secure panels and assemblies inside your appliance. Replacing missing or damaged hardware restores a tight, rattle-free fit and helps maintain proper alignment of parts.

• Fastens appliance components using an M5 x 0.8 machine-thread
• Replaces missing, loose, or stripped screws
• Helps reduce vibration and rattling noises
• Maintains correct alignment of brackets, panels, or internal assemblies

• Disconnect power before servicing; if working near water connections, shut off the supply.
• Match thread and length to the original screw and replace in the same location.
• Start threading by hand to avoid cross-threading; use the correct driver and do not overtighten.
• Reinstall any original washers or lock hardware used with the screw.

This gasket forms a tight seal between mating components in your appliance, helping contain water, air, or heat as designed. Replacing a worn gasket restores proper sealing and helps prevent leaks, performance loss, and residue buildup. What it does:

• Creates a compressible seal between two parts to prevent leakage and maintain proper airflow or water containment
• Helps reduce rattles and wear at the joint by cushioning the connection
• Supports efficiency and consistent performance by keeping the system properly sealed
• Common symptoms of failure: visible cracks/tears or flattening, leakage at the joint, heat or moisture escaping, or persistent odors near the seal

• 1 gasket

• Disconnect power; shut off water supply before servicing
• Note the gasket's orientation and take reference photos during disassembly
• Remove the old gasket and thoroughly clean mating surfaces of residue or debris
• Seat the new gasket evenly without stretching; reassemble and test for a proper seal

The Support Roller Washer is an OEM part for Frigidaire dryers, designed to ensure the smooth and stable operation of the dryer drum. Positioned between the support roller and the shaft, this washer plays a critical role in reducing friction and wear, allowing the drum to rotate smoothly and quietly.

Causes of these symptoms often stem from normal wear and tear, which can lead to the degradation of the washer over time.  

Symptoms of a bad Dryer Support Roller Washer include:

• Unusual noises, such as squeaking or grinding, indicating increased friction during drum rotation
• The dryer drum appears to wobble or is misaligned during operation
• Increased vibration of the dryer, which can lead to wear on other components

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This factory fastener secures appliance components and cabinet panels. Replacing a stripped, rusted, or missing screw restores a tight fit, reduces rattles and vibration, and keeps parts aligned for reliable operation. What it does:

• Fastens brackets, panels, and internal components to the cabinet/frame
• Helps maintain alignment and stability under vibration
• Direct replacement when the original is lost, corroded, or threads are damaged
• Common symptoms: loose or rattling panels, gaps/misalignment, or visibly missing hardware

• 1 screw

• Disconnect power; shut off gas/water if applicable before servicing
• Support the panel or component while removing/starting screws
• Match location and length to the original; start threads by hand to avoid cross-threading
• Tighten snugly—do not overtighten to prevent stripping

This small spacer fits on the idler assembly shaft to properly space and align the belt tensioner. Replacing a worn spacer helps keep the drive belt tracking correctly so the drum/tub runs smoothly and quietly. What it does:

• Spaces and centers the idler pulley on its shaft
• Helps maintain proper belt alignment and tension
• Can reduce squeaking or chirping from the idler area
• A worn or missing spacer may let the belt ride off, fray, or stop the drum/tub

• 1 idler spacer

• Disconnect power before servicing; let hot components cool
• Access the idler assembly per your model, relieve belt tension, and remove retaining hardware to slide off the pulley and old spacer
• Install the new spacer in the same location/orientation; reassemble and route the belt correctly
• Rotate the drum/tub by hand to verify smooth belt tracking before restoring power

Replacement striker for the refrigerator door latch that provides the catch point for the door to close securely. Restores proper door engagement to help maintain a tight seal and consistent internal temperature. What it does:

• Provides the catch point for the door latch so the door closes and stays latched
• Helps maintain an effective door seal to preserve cooling performance
• Common symptom: door won't stay closed, pops open, or fails to latch
• Also helps reduce drafts and noise caused by a misaligned latch

• Turn off power to the appliance before starting work
• Access the striker area, remove mounting fasteners, and replace with the new striker
• Align the striker so the latch engages smoothly; tighten screws securely
• Use care not to overtighten or strip mounting holes; replace damaged hardware as needed

This replacement seal restores a tight barrier between mating surfaces in your appliance, helping contain air, moisture, and heat where intended for reliable performance and efficiency.

• Forms a tight barrier to help prevent leaks, drafts, or heat loss
• Replaces a cracked, torn, flattened, or missing seal
• Can help address issues like moisture around an opening, temperature fluctuations, or rattling/vibration from a poor fit
• Restores proper closure and performance when the original seal is worn

• Disconnect power and shut off water/gas before service
• Note the routing/orientation of the original seal; take photos for reference
• Clean the channel/mating surfaces thoroughly; remove old adhesive and debris
• Seat the new seal fully without stretching; close and test for proper fit and contact

Replacement cover that restores the appliance's finished appearance while shielding internal components from dirt and accidental contact. Fits the original mounting points for a clean, factory look and safe operation. What it does

• Protects internal wiring and components from dust, spills, and accidental contact
• Restores the appliance's finished appearance when the original cover is cracked, broken, or missing
• Helps reduce noise from loose or exposed parts by holding components in place
• Prevents fingers and tools from reaching sensitive areas during normal use

• Disconnect power to the appliance before beginning any repair.
• Remove fasteners or release retaining tabs carefully to avoid breaking plastic clips.
• Align mounting tabs and secure with original hardware; do not force or over-tighten.
• If clips are damaged, replace them before reinstalling the cover.

This electronic control board is the machine's brain, directing power and timing for each selected cycle. Replacing it restores responsive controls and reliable operation.

• Directs power to motors, valves, heaters, pumps, and fans per cycle selection
• Interprets inputs from sensors and switches to adjust operation
• Stores and executes timing/logic and manages error routines
• Failure symptoms include unresponsive controls/display, won't start, stops mid-cycle, cycle won't advance, intermittent operation, or error codes

• Disconnect power at the breaker before servicing; verify zero voltage.
• Use ESD protection and handle the board by the edges only.
• Photograph/label wiring and transfer connectors one by one to the new board.
• Mount securely in the existing bracket/enclosure, restore power, and run a test; for any model-specific resets.