Ew30ef65gs Parts

This oven rack provides a sturdy, level surface for cookware inside your range or wall oven. Replace a bent, rusted, or missing rack to restore safe support and smooth, reliable placement at the proper cooking height.

• Slides into the oven's side rails to hold pans at the desired level
• Supports bakeware evenly and maintains proper clearance for airflow
• Replace when the rack is warped, corroded, flaking, or difficult to slide
• Common symptoms include wobbling, not sitting level, or a missing safety stop

• Allow the oven to cool completely; wear gloves to protect from sharp edges
• Insert the rack with the stop end toward the rear; engage both side rails evenly
• Push in until the rear stops seat; the rack slides freely and sits level
• To remove, pull to the stop, lift the front slightly, then pull straight out

This is a nut that is used in many microwave ovens. It is typically used to hold interior fan in place. A nut is a fastener that is used to hold two items together or keep one component secure against a surface. Use and time can cause the nut to become stripped, damaged, or broken. If the nut is broken, it will no longer hold the fan in the right location. The nut will need to be replaced.Before replacing this part, the microwave should be unplugged. Open the refrigerator door and remove the cover that goes over the fan. The nut can then be removed using a nut driver. Replace the other parts before using the appliance.This nut is used in microwave ovens manufactured by Crosley, Electrolux, Frigidaire, and Kenmore. It is sold as a single part. This is an authentic OEM replacement part is sourced directly from the manufacturer.

This factory screw secures panels, brackets, and other components in your cooking appliance. Replace a missing, stripped, or corroded fastener to restore a tight, rattle-free fit and keep parts properly aligned during use.

• Fastens components to maintain proper alignment and stability
• Helps prevent vibration, rattling, and loose parts during operation
• Replace if threads are stripped, the head is damaged, or the screw is missing
• Commonly used to mount internal or exterior parts in ranges and wall ovens

• Disconnect power and allow the appliance to cool; shut off gas supply if applicable
• Use the correct driver bit to avoid stripping the screw head
• Install in the original location and do not overtighten
• If the receiving threads are damaged, repair or replace the mating part before installation

This replacement fan motor spins the appliance's fan to move air for cooling and circulation during operation. Replacing a worn motor restores proper airflow, helps protect internal components from heat, and can reduce noise from failing bearings.

• Drives the fan to move air through the appliance as designed
• Common fix for a fan that won't run or turns slowly
• Can help prevent overheating, hot control panel, or thermal shutdowns

• Disconnect power at the breaker or unplug the appliance; allow hot surfaces to cool
• Access point varies by model; remove panels to reach the fan motor
• Note wire positions; transfer the fan blade and any mounting hardware from the original motor if required
• Restore power and test

The Triple Radiant Surface Element is an OEM part for Frigidaire ranges and cooktops. This component features three individual electric coils contained within a single mounting unit.

The triple element provides versatile cooking options with three distinct zones that heat up rapidly and evenly. Whether simmering a sauce or boiling water, this element allows home chefs to prepare multiple recipe components simultaneously. Precise thermostat controls maintain selected temperatures accurately.

Causes of bad triple elements can include broken internal wiring from shifting or impact over time, or mineral buildup impeding heat transfer and coverage.

Symptoms of failure include:

• Only one or two coils heating up out of three
• Discoloration, cracking or pitting of the coil surfaces
• Coils that pulse or cycle excessively in lower heat settings

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.
 

This replacement part is a black element mounting clip used in ranges or wall ovens. This clip is used for surface elements on electric ranges and ovens. The clip itself connects the surface of the element to the support bracket which allows the stove to heat up. The user might need a new clip or clips if the heating element on the stove is loose, if the heating element is completely detached, or if the clip itself is bent or broken. This clip is black and made of sturdy metal that can withstand heat as well as strain on the clip itself. Installation of this clip is very simple as it just requires replacing the old one with a new one and making sure it is secure. Pliers might be required if the old clip is bent or stuck near or on the heating element. There are no special tools needed for this repair. This is an OEM part sourced directly from the manufacturer. It is sold individually. This part is compatible with machines from Frigidaire and other brands like Electrolux, Gibson, Kelvinator, Crosley, Westinghouse, and more.

Size: 8-32t x 0.500 inch. Color: Black.

This is the electronic clock/timer that controls the oven. It manages bake and broil functions and provides the display and timing, helping restore proper heating and responsive controls when the original board fails. What it does:

• Controls oven heating by sending power to the bake and broil circuits based on user selections
• Drives the clock, temperature, and status display
• Interfaces with the keypad to run timed baking and other oven functions
• Common failure symptoms can include no display, unresponsive buttons, error codes, or an oven that won't start or heat consistently

• Electronic control board (clock/timer) module

• Disconnect power at the breaker before servicing
• Access the control through the console/control panel; remove mounting screws to reach the board
• Label or photograph wiring and move connectors one at a time to the new board
• Handle by the edges to avoid static damage; secure all mounts and test operation after reassembly

This clear glass shelf provides a sturdy, easy-to-clean storage surface for your refrigerator, helping keep food organized and visible. It restores usable shelving space when an original shelf is cracked, chipped, or missing. What it does:

• Supports food containers, plates and small appliances so items stay organized and level.
• Prevents spills and crumbs from falling to lower compartments; makes clean-up quicker.
• Replaces cracked, chipped or broken shelves that can cause items to shift or fall.
• Restores a proper storage surface when the original interior shelf is damaged or removed.

• Remove food and any loose items from the shelf area before replacing the glass.
• Handle with care and wear cut-resistant gloves; support the glass from underneath while sliding into place.
• Inspect shelf supports or rails for damage and position the glass evenly on the supports; do not force the shelf into misaligned rails.
• Refer to your appliance's owner manual or service guide for model-specific placement instructions.

This oven door latch assembly locks the door during self-clean and reports lock status to the control. Restores proper door locking and unlocking so bake and clean cycles can run safely and without interruptions. What it does:

• Secures the oven door during self-clean and when commanded by the control
• Provides locked/unlocked position feedback to the electronic control
• Helps resolve issues such as a door that won't lock or unlock
• Can address self-clean cycles that won't start or complete and lock-related error messages

• 1 latch assembly

• Disconnect power at the breaker and allow the oven to cool completely
• Access varies by model; you may need to pull the unit and remove the rear or top/control panel
• Photograph wire connections and linkage before removal; transfer any mounting hardware from the original
• After installation, test the lock operation before final reassembly

This electronic oven control board governs your range's heating functions and displays the time and timer. Replacing a failed board restores reliable bake/broil operation, accurate temperature control, and a responsive clock/timer interface. What it does:

• Controls bake/broil circuits to run selected cooking modes
• Monitors the oven temperature sensor and regulates heat to the set temperature
• Drives the time-of-day and countdown timer display
• Interprets keypad inputs for mode selection and settings
• Failure symptoms can include no heat or erratic heat, a blank or flickering display, or unresponsive buttons

• One electronic control board assembly

• Disconnect power at the breaker before servicing; verify no voltage is present
• Use anti-static precautions and handle the board by its edges
• Photograph wiring and transfer connectors one at a time to the same positions
• Reuse the existing mounting hardware and any faceplate/overlay as required; set the clock after restoring power

Restore reliable top heat for broiling and browning. This replacement broil heating element brings your oven's broil function back to full strength so foods brown evenly and the broiler heats when selected.

• Provides high, direct heat from the top of the oven during the broil cycle
• Helps with top-browning in some baking/roasting modes
• Common failure signs: broiler won't heat or glow, uneven browning, visible breaks or blistering on the element
• Often tests "open" (no continuity) when failed

• Disconnect power at the breaker before servicing; allow the oven to cool completely
• Remove mounting screws, then gently pull the element forward and support the wires
• Label and transfer wires to the new element one at a time; do not allow wires to slip back into the rear cavity
• Reinstall screws, ensure secure connections, restore power, and test the broil function

This control mounting hex nut secures the burner or oven control to the control panel, keeping the shaft stable so the knob turns smoothly and the switch stays properly aligned.

• Threads onto the control/infinite switch or thermostat bushing to fasten it to the panel
• Prevents the control from rotating or shifting when the knob is turned
• Replace if the original nut is missing, stripped, rounded, or corroded
• Common signs: loose or wobbly knob, switch spins in the panel, or misaligned knob indexing

• Disconnect power; for gas appliances, also shut off gas before servicing
• Pull off the knob and any trim; support the control body from behind the panel while removing/installing the nut
• Start the new nut by hand to avoid cross-threading; tighten snugly with the correct-size wrench—do not overtighten
• The control sits square in the panel and the knob operates smoothly before restoring power

This factory replacement plate is used on Frigidaire-made cooking appliances to cover and support a specific area of the unit. Replacing a bent or missing plate restores proper protection, alignment, and a clean, finished appearance. What it does

• Covers an opening or shields internal components as designed for the model
• Provides a stable mounting surface for adjacent parts or hardware
• Helps prevent debris intrusion and potential rattles or vibration
• Common signs it's needed: plate is missing, bent, cracked, or won't fasten securely

• 1 plate

• Disconnect power (and gas, if applicable) and allow the appliance to cool before servicing
• Retain and reuse existing screws/fasteners unless your model specifies new hardware
• Align the plate with existing holes; start screws by hand to avoid cross-threading and tighten evenly
• Verify clearances and safe operation before restoring power

This convection fan element mounts on the oven's rear wall around the blower. It supplies supplemental electric heat so the fan can circulate hot air evenly during convection modes for more consistent baking and roasting.

• Provides heat directly around the convection fan to help maintain even temperature during convection cycles
• Failure can cause poor browning, uneven results on multiple racks, or convection modes that run without proper heating
• May show visible breaks, blistering, or burnt spots; an open element will fail a continuity check
• If standard bake heats normally but convection bake does not, this element may be at fault

• Disconnect power at the breaker and allow the oven to cool completely before servicing
• Remove oven racks and the rear interior panel to access the element surrounding the fan
• Note wire positions; transfer any spacers or mounting hardware from the original element as needed
• Secure the element without bending it and confirm the fan spins freely with proper clearance

This electronic control board is the "brain" of the oven, managing cooking modes, temperature regulation, and the clock/timer display. Replacing a failed board restores proper heating and responsive controls for reliable day-to-day cooking.

• Controls bake/broil relays and regulates oven temperature using sensor feedback
• Powers and updates the clock, timer, and oven display
• Interprets keypad inputs for mode selection and temperature settings
• Common failure symptoms: oven won't heat or start a cycle, temperature is erratic, display is blank/flickering, buttons unresponsive, or beeping/error codes

• Disconnect power at the breaker before servicing; verify no voltage is present
• Use ESD precautions and handle the board by the edges
• Photograph wire connections and transfer any brackets/overlay from the original as required
• After installation, run a test bake to ensure proper operation and clear any stored errors