Ffb02409ls0a Parts

This replacement pump moves water/condensate through your appliance so it can drain or recirculate as designed. Replacing a weak or failed pump restores proper water removal and helps prevent leaks, overflows, or nuisance shutoffs.

• Moves collected water from the sump/collection area to a drain hose or internal passage
• Maintains correct water level to prevent overflow conditions
• Common failure signs: water won't pump out, leaks near the base, or loud buzzing/grinding from the pump
• May trigger "bucket full," drain, or pump-related error indicators, depending on the model

• Disconnect power before servicing; allow unit to cool, and expect residual water in the lines or pan
• Note hose routing and wiring connections; transfer any clamps, grommets, or fittings from the old pump if reused
• Ensure hoses are fully seated and not kinked; tighten connections and check for leaks after reassembly
• Test operation after installation and water is expelled properly

Set of 8 screws and washers.

This replacement bracket is used in Frigidaire-made dishwashers to secure an associated component or panel. Replacing a broken or missing bracket restores a tight fit, alignment, and stability so parts don't loosen, rattle, or shift during cycles. What it does:

• Provides a rigid mounting point for the connected part or panel
• Maintains proper alignment and stability during operation
• Helps reduce rattling or vibration from a loose component
• Replaces a broken, bent, rusted, or missing bracket

• 1 bracket

• Disconnect power and turn off the water supply before servicing
• Access and mounting location vary by model; refer to your service or installation manual
• Wear cut-resistant gloves; bracket edges may be sharp
• Save and reuse the original screws/fasteners; install in the same orientation and tighten securely

This replacement sealing gasket restores a tight, reliable seal between mating parts in your appliance. A proper seal helps prevent leaks and bypass, reduces noise, and supports overall performance and efficiency.

• Creates a compressible seal between components to prevent air or moisture bypass
• Helps maintain correct airflow/temperature containment for proper operation
• Reduces vibration and rattling caused by hardened or damaged seals
• Replace if the original is torn, flattened, brittle, missing, or leaking

• Disconnect power before servicing; shut off water supply if applicable
• Remove the old gasket and clean mating surfaces of residue/debris
• Match the original routing/orientation; do not stretch or over-compress the gasket
• Tighten fasteners evenly to ensure a uniform seal; verify no pinching or gaps

The Insulation is an OEM part for Frigidaire dishwashers. It is designed to reduce sound during wash cycles and help create a quieter dishwasher experience. The sound insulation minimizes noise transmission by absorbing and dampening vibrations throughout washing.

Causes of bad sound insulation can include breakdown of insulating materials over time, compression that reduces soundproofing density, or water damage or impacts.

Symptoms of bad sound insulation include:

• Noticeably louder operations with minimal sound dampening
• Rattling, banging, or buzzing sounds emanating from the appliance
• Transference of vibrations that causes adjacent cabinets to resonate

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This switch assembly is used in select dishwashers to provide a precise open/closed electrical signal to the control. Replacing a worn or sticking switch helps restore consistent cycle operation and reliable responses from the affected function. What it does:

• Sends an on/off (open/closed) signal to the control for the related mechanism in your model
• Helps ensure the connected function engages only at the correct time
• Common symptoms of a failed switch can include: cycle won't start, intermittent stopping, or improper filling/draining behavior
• A sticking or heat-damaged switch may cause erratic operation or error alerts

• One switch assembly

• Disconnect power (and water supply if required by access) before servicing
• Access location is model-specific; photograph wiring and note terminal positions before removal
• Transfer or reuse existing mounting hardware as applicable; ensure firm terminal connections
• After install, check switch actuation and run a test cycle to normal operation

This basket assembly replaces a damaged or missing basket in your appliance to restore organized storage and proper support for items. A precise, model-specific fit keeps contents secure and helps maintain accessible, usable space.

• Provides a designated container/support for contents within the compartment
• Helps prevent items from tipping or shifting due to a cracked or warped basket
• Restores lost capacity and correct fit when the original basket is broken or missing
• Direct replacement engineered to fit the original mounting location in your model

• Disconnect power and remove any contents before servicing
• Note the basket's orientation and engagement with rails/tabs before removal
• Transfer and reuse any original screws or clips if your model uses them
• Seat the new basket fully and verify a secure fit and smooth operation

This lower toe plate mounts at the base of the dishwasher's front. It covers the gap beneath the door to protect internal components and restore a clean, finished look when the original kick panel is dented, cracked, or missing.

• Covers the open area beneath the door at the base of the cabinet
• Shields wiring, hoses, and internal components from bumps and debris
• Restores a clean, finished front appearance
• Common symptoms: panel is bent, cracked, loose/rattling, or missing

• Disconnect power to the dishwasher before servicing
• Remove the mounting screws securing the existing toe plate and lift it away
• Position the new panel and secure with the existing hardware; do not overtighten
• Verify alignment and door clearance after installation

This sump gasket seals the connection between the dishwasher tub and the sump/pump assembly. Replacing a flattened or cracked gasket restores a watertight barrier to help stop leaks from the base and protect floors and cabinetry.

• Creates a seal between the tub and sump to contain wash water
• Helps prevent leaks during fill, wash, and drain cycles
• Replace if the gasket is cracked, brittle, deformed, or compressed
• Common symptoms: water under the dishwasher, dripping from the base, moisture around the toe-kick

• Disconnect power and shut off the water supply; pull the dishwasher out if needed for access
• Access the sump area (often by removing the lower rack, spray arm, and filters); note gasket orientation
• Clean mating surfaces; seat the gasket evenly without twists. Do not use sealants unless specified by the manufacturer
• Reassemble and run a short test cycle while inspecting for leaks

Used on the upper rack track

This kickplate assembly is the lower front panel at the base of the dishwasher. It restores a clean, finished look while helping shield internal components from kicks, dust, and splashes at floor level.

• Covers the lower access opening and completes the cabinet base
• Helps protect wiring, pump, and insulation from debris and impact
• Aids in noise dampening when properly installed
• Replaces panels that are bent, dented, scuffed, or missing
• Common symptoms: loose/rattling panel, visible gap under the door, cosmetic damage

• Disconnect power at the breaker; shut off water if working near supply lines
• Remove existing panel mounting screws and retain hardware for reuse
• Align the new panel and secure with the screws; do not overtighten
• Restore power and test

This thermostat retainer is the mounting clip that keeps the dishwasher's thermostat secured to its base or bracket. Proper retention helps maintain accurate temperature sensing and consistent heater safety through the wash and dry portions of the cycle. What it does:

• Holds the thermostat firmly in place on the base or mounting bracket
• Prevents the thermostat from shifting, vibrating loose, or falling out of position
• Supports accurate temperature sensing and overheat protection
• Common signs of a bad/missing retainer: broken or warped clip, thermostat hanging loose, intermittent heat/drying performance

• 1 thermostat retainer

• Disconnect power and shut off water before servicing
• Remove the lower access/toe-kick panel to reach the thermostat area
• Note the thermostat's orientation; transfer it to the new retainer and snap/secure the retainer to the existing mount/hardware
• Ensure the thermostat is fully seated and wiring is routed clear of sharp edges and hot/moving components

This sump assembly is the dishwasher's lower-tub pump housing that circulates and drains wash water. Replacing a cracked or clogged sump restores proper drain and circulation, helping stop leaks and restore normal wash performance. What it does:

• Houses the pump and channels wash water for circulation and draining.
• Restores proper drainage when the dishwasher won't drain or holds water in the tub.
• Stops leaks that develop from cracked or damaged sump housings at the base.
• Reduces pump noise or grinding caused by debris, cracks, or a failing housing.

• Disconnect electrical power and water supply before beginning any service.
• Access the sump from the dishwasher's lower front (remove the lower rack and toe-kick/access panel as needed).
• Take care with wiring and hose clamps; transfer any motors, seals, or fittings only if required and follow manufacturer torque/placement.
• After installation, run a short cycle and inspect for proper drain/circulation and any leaks before reassembling trim.

This replacement hose restores a secure, leak-resistant path for air or condensate in your appliance. Replacing a cracked, kinked, or brittle hose helps maintain proper flow, prevents leaks, and supports overall performance.

• Channels air or water as designed to ventilate or drain the unit
• Helps maintain a sealed connection at fittings to minimize leaks
• Flexible design supports correct routing without sharp kinks
• Common symptoms: visible cracks or brittleness, kinks, leaks, poor draining or reduced airflow

• Disconnect power and, if applicable, shut off water before servicing; allow components to cool.
• Place towels/containers to catch residual water; wear gloves to protect from sharp edges.
• Transfer and reuse existing clamps/adapters if required; replace any worn seals or clamps.
• Route without sharp bends; fully seat and secure both ends; test for leaks or airflow after installation.

The Defrost Sensor is an OEM part for Frigidaire refrigerators. It is responsible for monitoring the temperature in the freezer and initiating the defrost cycle when necessary. It works with the defrost heater and control board to regulate the defrost cycle, preventing the buildup of ice and frost in the freezer compartment.

A bad defrost sensor can be caused by electrical issues, sensor failure, or physical damage. Common signs of a malfunctioning sensor include excessive frost or ice buildup in the freezer, inconsistent temperature control, or the refrigerator not cooling properly.

Symptoms of a faulty defrost sensor include:

• Excessive frost or ice in the freezer
• Inconsistent temperature control 
• Inadequate cooling  

Replace your defective or damaged defrost temperature sensor with this genuine OEM Frigidaire part to restore your refrigerator. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.