Ffhtt1826lq2 Parts

This replacement water tube routes water within the refrigerator's internal water system. Installing a fresh, intact tube helps stop leaks and restores reliable water flow to the dispenser and ice maker. What it does:

• Carries water between components such as the inlet valve, reservoir, dispenser, and ice maker
• Maintains a sealed, kink-free path for proper flow and pressure
• Common signs of failure: leaks or puddling, weak or no dispenser flow, ice maker not filling, brittle or discolored tubing

• One tube

• Unplug the refrigerator and shut off the water supply before servicing
• Note the original routing; take photos to match length and path
• If trimming, cut ends square and fully seat into the existing push-to-connect or compression fittings
• Restore water and check all connections for leaks before powering the unit back on

This defrost pan collects water from the refrigerator's automatic defrost cycle and sits over warm components so it can evaporate safely. Replace a cracked or deformed pan to help prevent floor puddles and musty odors. What it does:

• Collects defrost condensate and allows it to evaporate in the machine compartment
• Helps keep floors dry by managing defrost water
• Replace if the pan is cracked, warped, leaking, or missing
• Common symptoms include water under the refrigerator, recurring puddles, or musty odors

• 1 defrost drain pan

• Disconnect power and pull the refrigerator away from the wall before servicing
• Remove the rear access panel to reach the drain pan
• Slide out the old pan carefully and empty any water; reuse any original supports/brackets if present
• Set the new pan on its supports, ensure the drain outlet/tube drips into the pan, reinstall the panel, restore power, and check for leaks

This aluminum strap secures the defrost heater firmly against the evaporator coil to maintain proper contact during defrost. Correct contact improves heat transfer so frost melts evenly and helps prevent recurring ice buildup on the evaporator.

• Secures the defrost heater to the evaporator for proper contact and heat transfer
• Promotes complete, even defrosting across the evaporator coil
• Helps reduce repeat frost/ice accumulation caused by a shifted or loose heater
• Typical clues include a loose heater, uneven frost pattern, or rattling near the evaporator

• Disconnect power and allow ice to melt before accessing the evaporator
• Use care around sharp fins and fragile refrigerant tubing; do not puncture or deform the coil
• Position the heater per your model's parts diagram and tighten the strap for firm, even contact
• Verify wiring is routed clear of the fan and moving parts before reassembly

The Power Cord is an OEM replacement part for Frigidaire refrigerators. As the lifeline connecting the appliance to a wall outlet, this cord safely delivers necessary voltage to operate refrigerator systems. 

Potential causes for needing a new power cord include exposure to cuts, abrasions or rodent damage over time in the storage area. Repeated bending stress during installation or removal can also wear out plastic insulation faster.

Symptoms of a faulty power cord include: 

• Refrigerator fails to power on at all
• Flickering lights or inconsistent runs of the compressor  
• Shock, buzzing or humming sounds coming from the cord
• Bare copper wire showing through damaged insulation

This power cord also fits some Electrolux and Gibson refrigerators.

The Evaporator Fan Blade is an OEM component specifically designed for Frigidaire brand refrigerators. This fan blade is located within the evaporator coil assembly and works to circulate cold air throughout the refrigerator compartment. 

Symptoms of a bad fan blade include: 

• Excessive heat buildup inside refrigerator sections
• Inability to sufficiently cool foods or maintain temperatures  
• Vibration or grinding noises emanating from rear wall
• Complete lack of air circulation felt at vents

Causes for replacement include wear and tear of plastic components over many years of constant spinning motion, cracks, or breakage from foreign object interference.

This genuine OEM Frigidaire part is also compatible with some Kelvinator and Admiral models.

This plug covers the small factory test opening on an appliance cabinet or liner. Replacing a missing or damaged plug helps close the opening to maintain a better seal and restore a clean, finished appearance.

• Seals the factory test opening in the cabinet/panel
• Helps limit air and moisture infiltration through the hole
• Reduces condensation or frost forming around the opening
• Restores a finished look when the original cap is missing or damaged

• Disconnect power before servicing the appliance
• Clean and dry the opening area for proper fit
• Align and press the plug in by hand until it sits flush—do not force or enlarge the hole
• Avoid sharp tools or sealants that could damage the liner or insulation

This door stop limits the opening range of your refrigerator door to prevent overextension and hinge strain. Replace a worn or broken stop to restore controlled door movement and protect surrounding cabinetry from accidental impacts. What it does:

• Controls how far the door opens to prevent overextension and damage
• Helps maintain proper door alignment and reduces stress on the hinges
• Replaces cracked, deformed, or missing stops that no longer hold the door at its stop point
• Common symptoms include the door swinging too far, a hard "clunk" at full open, or visible damage to the stop

• 1 door stop

• Disconnect power; turn off water supply if your unit has a dispenser/ice maker
• Support the door before loosening any hinge fasteners to access the stop
• Note the stop's orientation and position; transfer any spacers and reinstall the same way
• Open and close the door to verify proper range and clearance before fully tightening fasteners

Color: White

This compressor starter engages the start windings so the refrigerator/freezer compressor can begin running. When the starter fails, the compressor may not start, leading to warm temperatures and clicking or brief humming from the compressor area.

• Provides a brief, high-current assist to the compressor's start winding to initiate operation
• Automatically disengages after startup so the compressor runs normally
• Common symptoms of a faulty starter: compressor won't start, repeated clicking, brief hum then stop, little or no cooling
• Helps prevent repeated, hard start attempts that can stress the compressor

• Disconnect power before servicing; wear appropriate PPE
• Access the machine compartment; note wire positions/orientation before removal
• Pull the old starter straight off the compressor pins; seat the new starter fully and reconnect wiring
• Avoid stressing refrigerant tubing; discharge it per safe procedures

This replacement gasket restores a tight seal between mating parts in your appliance. Replacing a worn seal helps stop leaks and keeps performance steady by maintaining proper containment during normal operation.

• Creates a compressible barrier between components to prevent leaks and seepage
• Maintains proper system performance by preserving the intended seal
• Helps reduce vibration and wear at the joint
• Replace if cracked, flattened, brittle, warped, or if leaks are present around the connection

• Disconnect power; shut off water or gas if applicable
• Allow the unit to cool and relieve any pressure before service
• Clean and dry mating surfaces; remove the old gasket and residue
• Install without stretching; tighten fasteners evenly; do not use sealants unless specified by the manufacturer

This starter is the compressor's start device. It energizes the start winding so the compressor can begin running, helping restore reliable cooling performance. What it does and common signs it's bad:

• Supplies initial current to the compressor's start winding; disengages once the motor is running
• Symptoms can include a warm refrigerator/freezer, compressor not starting, clicking or humming every few minutes
• Can show heat damage or rattling when shaken after failure

• One compressor starter

• Disconnect power before servicing and pull the unit forward for rear access
• Remove the compressor cover; note wire positions and device orientation
• Firmly seat the new starter on the compressor terminals and reconnect the harness; reinstall the cover
• Restore power and observe compressor start-up; use cut-resistant gloves and follow the product's service information

This compressor mounting clip secures the compressor to its chassis to reduce movement and noise for reliable operation. It replaces worn or broken clips that allow the compressor to shift during use. What it does:

• Holds the compressor in place on the mounting bracket to prevent shifting
• Reduces vibration and rattling noises caused by a loose mount
• Helps maintain proper compressor alignment for steady operation
• Useful when a cracked or bent clip no longer secures the compressor

• Disconnect power to the appliance before accessing compressor area
• Inspect surrounding mounts and rubber isolators; replace if damaged
• Secure clip fully so compressor is held without forcing or misaligning components

The Drain Pan is an OEM part for Frigidaire refrigerators. It is located at the bottom of the refrigerator to collect any moisture, spills, or condensation. This pan helps keep the bottom of the refrigerator clean and dry.

Causes of a bad drain pan can include cracks or holes that allow leaks, corrosion that impacts drainage, or warping preventing proper fit.

Symptoms of a bad drain pan include:

• Puddles or standing water at the bottom of the refrigerator
• Musty smells from moisture build up
• Ice or frost accumulation underneath

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

Color: White

Replacement refrigerator door gasket restores a proper seal around the refrigerator door to help maintain steady internal temperatures and reduce frost, condensation, and cold-air leakage. Helps keep food fresher and supports consistent cooling. What it does:

• Seals the door-to-cabinet gap to help prevent cold air from escaping and warm air from entering.
• Helps reduce frost buildup and interior condensation when the door seals correctly.
• Common replacement when the gasket is torn, deformed, flattened, or the door no longer seals tightly.
• Restores sealing contact along the full door perimeter to support temperature stability.

• Disconnect power to the appliance before attempting any repair.
• Clean and dry the door flange and gasket channel before installing to ensure a proper seal.
• Seat gasket evenly around the door; inspect for gaps and correct fit before returning appliance to service.
• Follow OEM instructions for any recommended conditioning (warming/softening) or final adjustments.

Restore safe, level storage space with this refrigerator shelf assembly. Replace a broken or missing shelf to regain capacity and keep items organized and stable inside your appliance.

• Provides a flat, supportive surface for food storage in the designated compartment
• Helps keep items level and organized when properly seated in the support rails or clips
• Replace if the shelf is cracked, warped, or has broken end tabs/supports
• Common symptoms: shelf won't sit level or stay in place, wobbles/rattles, or is missing

• Remove food from the area; wear cut-resistant gloves and handle carefully to avoid damage or injury.
• Lift slightly and slide the old shelf out of the side rails; do not force against liners or tabs.
• Transfer any trim/end caps from the original shelf to the new one if required by your model.
• Slide the new shelf into the rails until fully seated and level.