Fghsz644kf1 Parts

Replace a cracked or worn bin to help restore dependable dispensing. This ice container assembly holds ice from the icemaker and, when you press the dispenser, moves it toward the chute for cube or crushed ice. What it does:

• Stores and contains ice in the freezer until dispensing
• Interfaces with the auger drive to feed ice toward the dispenser chute
• Works with the crusher/cube selection mechanism (model dependent)
• Common symptoms include no or slow dispensing, cracked/leaking bin, or ice jams/clumping

• 1 ice container assembly

• Disconnect power to the refrigerator before servicing
• Empty the old bin and pull it straight out of the freezer compartment
• Transfer any reusable parts from the old assembly
• Align the drive coupling and slide the new container fully into place; restore power and test dispensing

Nylon

The Door Light Switch is an OEM part for Frigidaire refrigerators. It is a component located inside the refrigerator door that turns the interior light on and off based on door position. The light switch works with a door switch plate and light socket assembly to automatically illuminate the interior when the door is opened.

Causes of a bad switch can be normal wear and tear over time, especially from frequent door openings. The contact points within the switch can become corroded or damaged.

Symptoms of a bad light switch include:

• Interior light not turning on at all when door is opened
• Light remaining constantly on even when door is closed
• Inconsistent or intermittent lighting

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.
 

This meat pan is the refrigerator's deli drawer. Replacing a cracked or missing bin restores smooth sliding access for meats and cheeses and helps keep the fresh food section organized.

• Creates a dedicated compartment for deli items in the fresh food section
• Slides on existing shelf rails for easy access
• Restores proper fit when the original bin is cracked, warped, or missing
• Common symptoms: broken or missing drawer, front lip cracked, drawer falls or won't slide smoothly

• Remove contents; pull the old drawer straight out from the rails
• Inspect and clean the rails; transfer any reusable parts from the old drawer if applicable
• Align the new pan on the rails and slide it fully into place
• If movement is tight, confirm the shelf cover and rails are seated and level

This spacer fits between the fixed crusher blades inside the refrigerator's ice bucket assembly. It preserves the correct gap and alignment so the auger turns freely and crushed ice dispenses smoothly without jams or grinding.

• Maintains the correct spacing between fixed crusher blades in the ice bucket
• Keeps the blade stack and auger aligned for smooth rotation
• Helps prevent ice jams, grinding noises, and inconsistent crushed-ice output
• Replaces a worn, cracked, or missing spacer discovered during service

• Disconnect power before servicing; remove the ice bucket from the freezer door/bin
• Carefully disassemble the crusher housing, noting the exact order of blades, spacers, and washers
• Wear cut-resistant gloves; crusher blades are sharp
• Reassemble in the original sequence and verify the auger turns freely before reinstalling

This evaporator fan motor mounting bushing isolates the motor from its bracket to reduce vibration and rattling. Replacing a worn bushing helps keep the fan secure and centered so airflow remains smooth and operation is quieter. What it does:

• Cushions and isolates the evaporator fan motor to reduce vibration and noise
• Helps maintain motor alignment to prevent the fan blade from rubbing the shroud
• Secures the motor to the mounting bracket
• Typical symptoms: rattling or buzzing from the freezer, fan wobble, loose motor, or a cracked/missing bushing

• One motor mounting bushing

• Unplug the refrigerator before servicing and wear safety gloves
• Remove the freezer back panel/evaporator cover to access the fan motor
• Support the motor, remove fasteners, and transfer/install the bushing on the bracket/motor as shown in your service diagram
• Ensure the bushing is fully seated and the fan blade spins freely with proper clearance before reassembly

This position-specific ice crusher blade (#1) fits inside the refrigerator's ice bucket assembly. It helps break up cubes into crushed ice; replacing a bent or worn blade restores consistent crushing and reduces jams or grinding noises during dispensing.

• Works with the auger and other numbered blades to crush ice when "Crush" is selected
• A bent, dull, or corroded blade can lead to no crushed ice, only cubes, slow dispensing, or scraping/grinding noises
• Restores even crushing and smoother auger rotation
• Position- and orientation-specific within the blade stack; match to your original

• Disconnect power and switch the ice maker OFF before servicing
• Remove and empty the ice bucket; allow any frost to thaw
• Disassemble the bucket front/auger and note the exact blade order and orientation—take photos for reference
• Wear cut-resistant gloves; reassemble blades, spacers, and washers exactly as removed and verify the auger turns freely before reinstalling

The Frigidaire Touch-Up Paint is white in color in a .6 fl oz bottle. For almond order 5303321320. For black order 5303321321.

The Touch Up Paint is an OEM part for Frigidaire appliances. Whether you're dealing with scratches, chips, or other minor cosmetic damage, this touch-up paint provides an easy and effective solution for maintaining the appearance of your appliance. It's designed to adhere well to metal surfaces, offering durability and resistance to further wear and tear.

Over time, appliances can accumulate minor surface damage from regular use, cleaning, and accidental impacts. Using the Touch Up Paint not only improves the aesthetic appeal of your appliance but also helps protect exposed areas from rust and corrosion, which can extend the life of the appliance.

Symptoms of needing Touch Up Paint include:

• Visible scratches or chips on the appliance's surface.
• Areas of rust or corrosion that need to be covered after treating the rust.
• The desire to maintain or improve the appliance's appearance for aesthetic reasons or to maintain its value.

The defrost drain pan collects water that melts off the evaporator during automatic defrost and holds it near the warm compressor so it can evaporate. Replacing a damaged pan helps prevent leaks, puddles, and odors around the base of the refrigerator.

• Collects defrost water routed from the evaporator drain
• Positions water in warm airflow near the compressor for evaporation
• Replace if the pan is cracked, warped, missing, or leaking
• Symptoms can include water on the floor, moisture under the unit, or musty odors

• Unplug the refrigerator; wear cut-resistant gloves
• Pull the unit forward and remove the lower rear access panel to reach the pan near the compressor
• Lift out the old pan; transfer any reusable clips/brackets; seat the new pan under the drain tube and ensure it's level and clear of moving parts
• Reinstall the panel, restore power, and check for proper drainage and evaporation

This replacement screw secures refrigerator components such as brackets, trims, and covers. Replace missing or stripped hardware to keep parts tight and aligned, helping eliminate rattles and restoring a solid, reliable fit.

• Fastens interior or exterior components to the cabinet or doors
• Replaces missing, rusty, or stripped hardware
• Helps reduce vibration noises from loose parts
• Restores proper fit and alignment of panels, trims, or covers

• Disconnect power; turn off water supply if working near the dispenser or ice system
• Retain and reuse any original spacers or washers
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Replace one fastener at a time to maintain alignment

This dispenser drip tray sits beneath the refrigerator's ice/water dispenser to catch drips and small spills, helping keep the area cleaner and reducing moisture on the door and surrounding surfaces.

• Collects water and ice drips under the dispenser
• Helps contain minor spills during dispensing
• Protects the door surface from moisture and staining
• Common signs of wear: cracked or missing tray, water pooling in the dispenser area, tray not sitting flush

• Disconnect power before working around the dispenser area
• Lift the old tray straight up and out of the recess
• Clean and dry the dispenser pocket to remove residue
• Align and press the new tray down until it sits flat and secure

This is the drive gear for the ice maker module. It transfers motor power to the ejector/harvest mechanism so cubes release consistently; worn or stripped teeth can cause clicking, stalls, or little to no ice production.

• Transfers motor torque to rotate the ejector and complete the harvest cycle
• Replaces a cracked, stripped, or worn gear that prevents proper ice ejection
• Typical symptoms: no ice production, icemaker stuck mid-cycle, clicking or grinding from the module
• Helps restore reliable ice maker cycling

• Unplug the refrigerator before service; turn off the water supply if moving the icemaker
• Remove the icemaker assembly for access; note the original gear's orientation before removal
• Align the new gear with the shaft; do not force it—inspect mating parts for wear
• After reassembly, verify the ejector turns freely; restore power and run a test cycle

This ice crusher blade (#2) mounts in the freezer's ice bucket assembly. It helps break up cubes for the Crushed Ice setting and can restore smooth dispensing when the original blade becomes bent, dull, or broken.

• Mounts inside the ice bucket crusher to slice/crush cubes when Crushed Ice is selected
• Helps maintain consistent ice flow and size through the dispenser
• Wear or damage may lead to no crushed ice, only whole cubes dispensing, jamming, or grinding noises
• Visible bending, dull edges, or a missing blade are common failure signs

• Disconnect power and remove the ice bin from the freezer
• Disassemble the crusher housing to access the blades; note the order/orientation of blade #1 and blade #2 before removal
• Wear cut-resistant gloves—edges are sharp
• Reassemble in the same order, tighten fasteners, reinstall the bin, and test the dispenser

This clip mounts to the refrigerator liner and secures the crisper cover/slide rail so the drawer stays supported and glides properly. Replace a broken or missing clip to restore alignment and smooth operation of the crisper.

• Holds the crisper cover/slide rail firmly against the cabinet liner
• Supports the crisper drawer to prevent sagging or tilt
• Helps restore smooth opening and closing of the crisper drawer
• Common symptoms of failure: loose rail, drawer off-track, difficulty sliding, or a cracked/missing clip

• Unplug the refrigerator or disconnect power before servicing
• Remove the crisper drawer and cover/glass to access the clip
• Release the old clip (snap tabs or screw), align and secure the new clip; reuse the original fastener if your model uses one
• Reinstall the cover and drawer; the drawer slides freely

This replacement glass insert fits into the crisper cover frame to create a sturdy, easy to clean surface above your produce drawers. Replace a cracked or missing insert to restore safe storage and proper drawer support.

• Sits in the crisper cover frame to support items above the drawers
• Helps contain spills to protect the drawers below
• Maintains correct spacing so crisper drawers open and close smoothly
• Replace when the original glass is cracked, chipped, shattered, or missing

• Unload the shelf and remove the crisper drawers
• Lift out the crisper cover frame and place it on a flat surface
• Remove the damaged glass and set the new insert into the frame recess without forcing
• Reinstall the cover and drawers; wear cut-resistant gloves and handle glass carefully

This dispenser module controls the refrigerator's ice and water dispensing functions and user interface. Replace a failed module to restore responsive dispensing, indicator lights, and consistent operation at the dispenser.

• Interprets button/paddle inputs and manages dispenser functions
• Coordinates ice and water dispensing operations
• Controls dispenser indicator lights/display for user feedback
• Failure can cause no dispense, unresponsive controls, or erratic/loss of lights

• Disconnect power and shut off water supply before service
• Remove the dispenser trim/panel carefully to access the module; protect against static discharge
• Note wire positions; transfer connectors and any reusable covers/overlays from the original part if applicable
• Restore power and test ice and water dispensing after installation