Fgsc2335tf9 Parts

This aluminum strap secures the defrost heater firmly against the evaporator coil to maintain proper contact during defrost. Correct contact improves heat transfer so frost melts evenly and helps prevent recurring ice buildup on the evaporator.

• Secures the defrost heater to the evaporator for proper contact and heat transfer
• Promotes complete, even defrosting across the evaporator coil
• Helps reduce repeat frost/ice accumulation caused by a shifted or loose heater
• Typical clues include a loose heater, uneven frost pattern, or rattling near the evaporator

• Disconnect power and allow ice to melt before accessing the evaporator
• Use care around sharp fins and fragile refrigerant tubing; do not puncture or deform the coil
• Position the heater per your model's parts diagram and tighten the strap for firm, even contact
• Verify wiring is routed clear of the fan and moving parts before reassembly

GRILLE/KICKPLATE

This refrigerator dispenser bearing supports the auger shaft so it spins smoothly during ice dispensing. Replacing a worn bearing restores quieter, more reliable ice delivery and helps prevent binding or uneven crushing of cubes. What it does

• Supports and centers the ice auger/crusher shaft inside the ice bucket
• Reduces friction to allow smooth, consistent rotation
• Wear can cause grinding or squealing during dispensing
• Symptoms include slow/no ice dispensing, jamming, or intermittent operation

• 1 bearing

• Disconnect power and turn off the water supply before service
• Remove the ice bucket and disassemble the crusher housing to access the bearing
• Note the bearing's orientation; transfer any spacers or clips as found
• Reassemble carefully and ensure the auger turns freely by hand before restoring power

This plug covers the small factory test opening on an appliance cabinet or liner. Replacing a missing or damaged plug helps close the opening to maintain a better seal and restore a clean, finished appearance.

• Seals the factory test opening in the cabinet/panel
• Helps limit air and moisture infiltration through the hole
• Reduces condensation or frost forming around the opening
• Restores a finished look when the original cap is missing or damaged

• Disconnect power before servicing the appliance
• Clean and dry the opening area for proper fit
• Align and press the plug in by hand until it sits flush—do not force or enlarge the hole
• Avoid sharp tools or sealants that could damage the liner or insulation

Color: White

Specs: 1.40`` long

This refrigerator clip is a small retainer that secures a component in place so it stays properly seated during use. Replacing a worn or missing clip restores a snug fit and helps eliminate looseness, rattling, or misalignment.

• Holds a part, panel, tube, or wire securely in its mounting point
• Maintains alignment to prevent shifting or vibration
• Helps preserve proper fit and airflow when components are correctly seated
• Symptoms can include loose or sagging pieces, rattling noises, or parts that won't stay attached

• Unplug the refrigerator; if working near water lines, shut off the water supply
• Note the clip's orientation before removal; take a photo for reference
• Use needle-nose pliers to release/install; avoid over-flexing the clip
• After installation, tug-test gently to confirm a secure fit before reassembling

This compressor inverter module powers and controls a variable-speed refrigerator compressor. When the inverter fails, the compressor may not start or modulate correctly, leading to warm temperatures or intermittent cooling. Replacing the module restores proper compressor drive.

• Converts AC line power to controlled 3-phase output for the variable-speed compressor
• Receives commands from the main control to start and regulate compressor speed
• Typical failure symptoms: refrigerator/freezer warm, compressor not running though fans/lights work, brief humming/clicking then stopping, intermittent cooling, or inverter/compressor error indications
• Mounts externally near the compressor and connects to the control harness and compressor terminals

• Disconnect power before servicing; high voltage is present at the inverter
• Access the rear lower compartment; transfer connectors one at a time to the new module and ensure tight terminal fits
• Reinstall on the original bracket/position to maintain cooling and ventilation around the inverter
• Restore power and allow up to 24 hours for temperatures to stabilize after repair

This condenser fan shroud sits in the rear machine compartment and positions the fan and motor to move air through the condenser coil. A cracked or warped shroud can reduce cooling performance and increase noise or vibration.

• Directs and focuses airflow across the condenser coil and compressor to remove heat
• Holds the condenser fan motor and blade in proper alignment
• Helps maintain stable refrigerator/freezer temperatures and efficient operation
• When damaged, may cause weak airflow, warmer temps, vibration, or fan scraping/rubbing noises at the back of the unit

• Unplug the refrigerator and wear cut-resistant gloves
• Pull the unit forward and remove the lower rear access panel to reach the machine compartment
• Take a photo of fan/motor orientation; transfer components to the new shroud and reuse existing hardware
• Confirm blade spins freely with proper clearance before restoring power

The Main Control Board is an OEM part for Frigidaire refrigerators. As the central "nerve center" regulating all appliance functions, it monitors temperatures, operating modes, and safety features through embedded computing power.

Symptoms of a faulty control board involve:  

• Failure to properly cool or function in temperature control modes
• Unresponsive display or non-working buttons and sensors  
• Error codes or diagnostic messages appearing

Common causes are moisture damage degrading circuit boards over time, electrical component burnout from power surges, or physical impact compromising fragile boards.

This OEM Frigidaire replacement part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore refrigerator models. 

This light switch controls the interior lamp, turning it on when the refrigerator door opens and off when it closes. Replace a worn or stuck switch to restore proper lighting and prevent the light from staying on. What it does:

• Door-activated plunger switch that opens/closes power to the interior light
• Restores interior lighting when the door is opened
• Resolves lights that stay on with the door closed, which can warm the compartment
• Addresses intermittent or flickering light from worn contacts

• 1 light switch

• Disconnect power before servicing
• Gently pry the old switch from the liner or remove the control housing as required for access
• Transfer the wire connectors to the new switch, matching positions
• Press the new switch fully into place, restore power, and test light operation

This door-activated light switch controls the interior refrigerator lighting, turning the light on when the door opens and off when it closes. Replacing a faulty switch restores proper lighting and helps prevent the light from staying on and warming the compartment.

• Opens/closes the light circuit based on door position
• Helps if the interior light won't turn on with the door open
• Fixes lights that stay on with the door closed
• Addresses intermittent or stuck plunger operation
• Restores normal visibility inside the refrigerator

• Disconnect power before servicing to avoid electrical shock
• Access the switch at the door liner or control housing; release tabs or screws as applicable
• Note wire positions, then transfer wires to the new switch one at a time
• The switch plunger moves freely and the light turns off with the door closed

Lower hinge secures the bottom corner of a refrigerator door and provides a durable pivot for smooth opening and closing. Replacing a worn hinge restores proper door alignment and helps maintain a tight seal. What it does:

• Supports the weight of the lower door corner and provides a pivot point for opening/closing.
• Keeps the door aligned so the gasket can seal properly.
• Worn or damaged hinges can cause door sag, uneven gaps, rubbing, or difficulty closing.
• Restoring a solid hinge reduces stress on the door and latch for more reliable operation.

• Disconnect power to the appliance and remove food/items from the door before starting.
• Always support the door while removing/installing the hinge to prevent dropping or damage.
• Use the correct tools and hardware; tighten fasteners snugly but avoid over-torquing.
• After installation, check door alignment and seal; adjust as needed for proper operation.

This factory fastener secures appliance panels and components. Replace a missing, stripped, or corroded screw to restore a tight, rattle-free fit and keep brackets and covers properly aligned.

• Fastens panels, brackets, and internal parts as specified by the manufacturer
• Helps maintain alignment and reduces vibration/rattling
• Replace if the head is stripped, threads are damaged, or corrosion is present
• Symptoms include loose/missing hardware, gaps, or rattling during operation

• Disconnect power; shut off gas/water if applicable before servicing
• Use the correct driver/bit size to avoid stripping the head
• Start threads by hand to prevent cross-threading; do not overtighten
• Match screw length/thread to the location; replace in sets when required

This replacement screw fastens appliance components such as panels, brackets, and covers. Installing a new fastener restores a snug, rattle-free fit when the original screw is missing, stripped, or corroded.

• Secures covers, brackets, or trim to the cabinet or liner
• Replaces missing, stripped, or rusted hardware
• Helps reduce vibration and rattling from loose parts
• Supports proper alignment and stability of assemblies

• Disconnect power before servicing the appliance
• Use the correct driver/bit and start threads by hand to avoid cross-threading
• Do not overtighten, especially into plastic or thin sheet metal
• Retain and reinstall any original washers or spacers, if present

Specs: .875`` long