Fph2399kf2 Display Parts

This freezer shelf provides a sturdy, level surface for organizing food in the freezer compartment. Replace a broken, bowed, or missing shelf to restore storage capacity and keep containers stable, accessible, and out of the air vents.

• Provides a flat, stable surface for food storage in the freezer
• Replaces cracked, warped, or missing shelf that won't sit level
• Helps maintain organization and efficient airflow
• Seats securely in the factory side supports when properly installed

• Disconnect power before servicing; remove food from the work area
• Lift the front edge and pull out to release the old shelf from the side supports
• Align the new shelf with the support rails; push back until fully seated and level
• Load food evenly and avoid overloading the shelf

This replacement door stop limits a refrigerator door's travel to prevent over-rotation, protect hinges and cabinet edges, and help keep the door aligned for a proper seal. Durable plastic replacement for a worn or broken stop. What it does:

• Stops the door at the correct travel point to prevent hitting adjacent cabinetry or walls.
• Reduces stress on hinge components to prevent premature wear.
• Helps the door sit square for a tighter seal and more consistent cooling.
• Common symptom: door swings past the normal stop, won't stay open, or the plastic stop is cracked/broken.

• Support the door while removing/installing the stop — fridge doors can be heavy and may shift.
• Use basic hand tools; do not overtighten fasteners to avoid cracking the new stop.

This thermostat retainer is the mounting clip that keeps the dishwasher's thermostat secured to its base or bracket. Proper retention helps maintain accurate temperature sensing and consistent heater safety through the wash and dry portions of the cycle. What it does:

• Holds the thermostat firmly in place on the base or mounting bracket
• Prevents the thermostat from shifting, vibrating loose, or falling out of position
• Supports accurate temperature sensing and overheat protection
• Common signs of a bad/missing retainer: broken or warped clip, thermostat hanging loose, intermittent heat/drying performance

• 1 thermostat retainer

• Disconnect power and shut off water before servicing
• Remove the lower access/toe-kick panel to reach the thermostat area
• Note the thermostat's orientation; transfer it to the new retainer and snap/secure the retainer to the existing mount/hardware
• Ensure the thermostat is fully seated and wiring is routed clear of sharp edges and hot/moving components

This LED light board powers the refrigerator's interior lighting, restoring bright, dependable illumination when the lights go dim, flicker, or stop working. It replaces the failed circuit board that drives the factory LED light module. What it does:

• Supplies regulated power to the refrigerator's interior LED light module
• Restores proper illumination in the fresh food and/or freezer sections (varies by model)
• Common symptoms: no interior light, dim light, flickering/strobing, or intermittent lighting
• Direct replacement for the original failed light control board

• 1 LED light board

• Disconnect appliance from power before servicing
• Handle the board by the edges and observe ESD precautions
• Note connector orientation; transfer lens/housing from the original assembly if required
• Ensure connectors are fully seated before restoring power

This spray arm assembly distributes high-pressure wash water inside the dishwasher and spins to cover the racks. Replacing a cracked or clogged arm restores proper spray coverage for cleaner dishes and consistent wash performance. What it does:

• Rotates as water flows to spray dishes evenly across the tub
• Channels water from the circulation pump through precision jets
• Helps resolve poor cleaning results or spots left on dishes
• Addresses issues like a spray arm that won't spin, clogged nozzles, or visible damage

• 1 spray arm assembly

• Disconnect power at the breaker and turn off the water supply before servicing
• Remove the rack if needed to access the arm
• Release the locking tabs or unthread the retaining cap to remove the old arm
• Seat the new arm fully, secure the retainer, and confirm it spins freely before a test cycle

The Drain Pump is an OEM part for Frigidaire dishwashers. It is responsible for removing water from the dishwasher tub at the end of each cycle. The drain pump works in conjunction with the drain hose to efficiently expel dirty water and ensure dishes are thoroughly dried.

Symptoms of a bad drain pump include:

• Water not fully draining out of the bottom of the dishwasher tub
• Puddles or standing water left inside after a cycle is finished
• Mildewy or musty smells emitting from the appliance
• Loud or grinding noises coming from the drain pump motor area

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This aluminum strap secures the defrost heater firmly against the evaporator coil to maintain proper contact during defrost. Correct contact improves heat transfer so frost melts evenly and helps prevent recurring ice buildup on the evaporator.

• Secures the defrost heater to the evaporator for proper contact and heat transfer
• Promotes complete, even defrosting across the evaporator coil
• Helps reduce repeat frost/ice accumulation caused by a shifted or loose heater
• Typical clues include a loose heater, uneven frost pattern, or rattling near the evaporator

• Disconnect power and allow ice to melt before accessing the evaporator
• Use care around sharp fins and fragile refrigerant tubing; do not puncture or deform the coil
• Position the heater per your model's parts diagram and tighten the strap for firm, even contact
• Verify wiring is routed clear of the fan and moving parts before reassembly

This seal-damper is the gasket that fits around a refrigerator's air damper to help keep compartments properly separated and maintain intended airflow. Replacing a torn or compressed seal helps reduce uneven cooling and drafts. What it does:

• Seals the air damper opening to limit unwanted air exchange between compartments
• Helps maintain stable temperatures by preventing cold or warm air leakage
• Common symptom fix: reduces uneven cooling or warm spots near the damper area
• Also helps reduce excess frost or condensation that can form from persistent air leaks

• Disconnect power to the appliance before starting any repair and remove nearby food/shelves for access
• Access the damper housing per your model's service instructions, remove the old seal, and seat the new seal onto the damper frame or mounting groove
• Clean the mounting surface of debris or old adhesive so the new seal sits flat; use gentle pressure to fully engage the seal
• If the damper housing is cracked or the seal does not seat properly, replace the damper assembly.

This refrigerator seal restores a tight barrier between internal components. Replacing a worn or damaged seal helps prevent air leaks and moisture intrusion, supporting proper airflow, stable temperatures, and reduced frost or condensation around the joint.

• Creates an air-tight barrier between mating surfaces
• Helps maintain correct airflow and temperature balance between compartments
• Reduces frost, condensation, and warm/cold spots near the sealed area
• Common signs of failure: visible gaps, loose/crumbled seal, rattling panel, moisture or frost at the joint

• Disconnect power before servicing
• Remove the related cover or housing to access the old seal
• Clean contact surfaces; install the new seal in the same orientation without stretching or pinching
• Reassemble and verify an even seal and normal airflow before returning to service

This fixed blade sits inside the refrigerator's ice bucket/crusher assembly. It provides a stationary cutting edge that works with the auger and rotating blades to break up cubes, helping your dispenser deliver consistent crushed ice.

• Stationary crusher blade that works with the auger and rotating blades to crush ice
• Helps prevent whole cubes from passing through on the "crushed" setting
• Worn, bent, or missing blades can cause poor crushing, jams, or uneven ice size
• May help address symptoms like dispenser jamming, irregular crushed ice, or increased grinding noises

• Unplug the refrigerator before servicing; remove and empty the ice bucket
• Note the order and orientation of blades, spacers, and fasteners; take reference photos
• Handle sharp metal edges; wear cut-resistant gloves
• Reassemble in the original sequence and tighten hardware snugly; ensure the auger turns freely before reinstalling

This replacement screw secures appliance components to their mounting points so panels, brackets, and trim stay tight and aligned. Replace missing or stripped hardware to restore a solid, rattle-free fit and proper assembly integrity.

• Secures panels, brackets, and trim to prevent movement and maintain alignment
• Replaces missing, damaged, or stripped hardware that can compromise assembly
• Helps reduce rattling or vibration from loose components
• Restores proper fit after service or access panel removal

• Unplug the appliance before servicing; turn off water supply if working near dispenser/ice areas
• Compare the new screw to the original to ensure thread, head style, and length
• Start threading by hand to avoid cross-threading; tighten snugly without over-torquing, especially into plastic
• Retain and reuse any original washers, spacers, or clips as required

This replacement gear restores the transfer of motion inside the refrigerator's mechanism so the assembly operates smoothly and reliably. Designed to match the original fit and drive characteristics for consistent performance.

• Transmits rotation between mating shafts/components within the assembly
• Worn or stripped teeth can cause stalling, slipping, or clicking/grinding noises
• Visual inspection often reveals rounded, cracked, or missing teeth

• Disconnect power before servicing
• Note the original gear's orientation and any timing/alignment marks before removal
• Transfer any clips, spacers, or washers from the original part as needed
• Inspect mating gears/shafts for wear and replace related parts to prevent repeat failure

Replacement water tube that routes water from the inlet valve to the refrigerator dispenser and ice maker, helping restore proper water flow for reliable dispensing and ice production. What it does:

• Carries water from the refrigerator inlet/valve to the dispenser and ice maker fill system.
• Used when cracked, kinked, clogged or brittle tubing prevents water flow.
• Helps stop leaks and restore normal ice maker fill when tubing is damaged.
• Addresses symptoms such as no water at the dispenser, ice maker not filling, or visible leaking under the fridge.

• Turn off the water supply and unplug the refrigerator before beginning any work.
• May require basic hand tools and careful routing to avoid kinks; do not overtighten fittings.
• Inspect and replace any damaged clamps or seals; test for leaks after reconnecting the water supply.

GRILLE/KICKPLATE

This slide set replaces the right- and left-hand rails that guide and support a drawer or rack. It restores smooth, aligned movement so the assembly opens and closes easily without sticking, wobbling, or jumping off the track.

• Guides and stabilizes the drawer/rack on both sides for smooth travel
• Maintains alignment to reduce binding, uneven movement, and premature wear
• Replaces worn, bent, or broken slides that affect operation
• Common symptoms: sticking, rough/grinding movement, tilt or sag, popping off track, hard to open/close

• Disconnect power; shut off gas/water. Remove the drawer or rack before servicing.
• Note L/R orientation; remove old slides and reuse existing screws/brackets.
• Install new slides in the same positions; ensure they are fully seated and aligned.
• Test movement several times before returning the appliance to service; wear cut-resistant gloves.

This water inlet tube routes water from the inlet valve to the ice maker and dispenser, restoring proper water flow and helping prevent leaks. Use when the original tube is cracked, split, or blocking water delivery. What it does:

• Directs water from the refrigerator inlet valve to the ice maker and dispenser assembly.
• Restores normal water flow if the original tube is crushed, cracked, or blocked.
• Helps stop leaks associated with damaged or deteriorated inlet tubing.
• Common symptoms: no water to ice maker or dispenser, slow dispenser flow, or visible leaking beneath the fridge.

• Disconnect electrical power and shut off the household water supply before starting.
• Handle tubing carefully and avoid sharp bends or kinks when routing.
• Check and reuse or replace any associated fittings, clips, or seals as needed for a secure, leak-free connection.