Fse4479hos Parts

Replacement mounting screw that secures appliance panels, trim or brackets to restore proper fit and reduce rattles. A simple fastener that helps keep components stable for safe, quiet operation. What it does:

• Secures panels, trim pieces or internal brackets in place
• Replaces lost, stripped or damaged screws that cause loose parts
• Helps stop rattling, vibration or misaligned panels
• Restores proper alignment so doors and covers sit flush

• Use the correct screwdriver or bit to avoid stripping the head
• Do not overtighten — snug until secure to prevent damage
• Disconnect power before working near electrical components
• Keep small parts away from children and pets

This white replacement plug fills and finishes an unused opening on the appliance, helping keep out dust and debris while restoring a clean, factory appearance. Use it where a small trim or access hole needs a discreet cover. What it does:

• Covers unused holes or access slots to protect internal components from dust and moisture
• Restores a finished, factory look to trim panels or consoles
• Helps prevent small items from falling into openings
• Simple, low-profile piece that stays recessed and unobtrusive

• No power required; work with the appliance unplugged or power turned off as a safety precaution when accessing trim
• Push the plug into the opening until it seats flush; a gentle push with a finger or soft tool is usually sufficient
• If removal is needed later, gently pry with a flat, non-marring tool to avoid scratching surrounding surfaces

Hex washer head ,10-32 x 0.375. Ground

Ceramic dryer heating element terminal block.

This wiring clip secures a refrigerator's wire harness to the cabinet or components to prevent chafing and keep wires organized. It helps maintain safe routing and reduces strain on electrical connections. What it does

• Holds wiring harness in place to prevent rubbing against sharp edges or moving parts
• Keeps wires organized to reduce the risk of pinching or accidental disconnection
• Helps prevent intermittent electrical faults caused by loose or strained wiring
• Commonly used near compressor, fan, control box, or rear cabinet areas

• Install by snapping the clip onto the cabinet flange or component and routing the harness through the retainer
• Disconnect power before accessing electrical components or wiring
• Inspect surrounding wiring and insulation; replace any damaged wire or harness tape before reinstalling the clip

This replacement dryer drum with a galvanized back restores smooth tumbling and helps keep clothes moving and drying evenly. Designed to match the OEM shape and fit for compatible Frigidaire dryers. What it does:

• Replaces a worn, dented or rusted dryer drum so garments tumble properly
• Reduces fabric snags, rubbing marks and uneven drying caused by a damaged drum
• Helps eliminate metal-on-metal noise from a cracked or scored drum surface
• Works with the existing rollers, seals and belt—restores the drum's rotation

• Disconnect power and move the dryer to a clear work area before starting
• Support the drum as you remove the front and rear panels to avoid damage
• Basic hand tools are required; have a helper for heavier lifts
• Inspect rollers, glides and the drive belt during installation and replace if worn

The Lower Front Felt Seal is an OEM part for Frigidaire dryers. This seal prevents hot air from escaping the dryer drum, ensuring optimal drying efficiency and preventing heat loss. It also helps reduce noise and vibration during operation.

Causes of a faulty lower front felt seal can include wear and tear over time, damage from foreign objects or excessive heat, or adhesive failure. These factors can result in air leakage, increased drying time, or excessive lint buildup.

Symptoms of a front felt seal may include:

• Air leakage around the dryer door or front panel
• Excessive lint accumulation near the dryer opening
• Unusual noises or vibrations during the operation

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Note: For the Hi-Temp Adhesive, order part number 5308027429. Additional parts to check are the rear drum bearing kit 5303281153 and the front felt glide assembly 5303937139.