Ge Wlsr3000g3ww Parts

Before buying a new ($1200) washer, I found the trouble shooting guide and decided to check if my problem was a simple fix or a complicated procedure... turns out it was the simple fix. Removing the agitator was the hardest part, it lifted straight up, but took some muscle and a belt for leverage. Then I had to remove one bolt, lift off the damaged part, and put the new part on with the one bolt. Done. Works perfectly. Read more

• Won't start

Replaced lid switch assembly Read more

The machine stopped working with a bang. There were chunks of large metal at the bottom. The drive plate had rusted through. My first step was to put a rag in the tub drain hole and save the pump. Except for grinding/chiseling off a frozen-corroded-rusty solid mass. The repair was rather easy. A couple of channel lock wrenches and a hammer didn't budge it. A monkey wrench will just round it off. You need that 1 11/6" wrench. The spindle nut was really stuck on there for my 14+ yo washer. I... Read more

• Will not stop filling with water

I replaced the water level switch and hose. After removing the hose, I found that it was clogged, and did not allow the water level to be sensed by the switch. A test after the replacement of the parts was successful. While filling the tub, the water shut off at the small, medium, and large levels as indicated by the switch. Read more

I pulled off the retaining clip with pliers then removed the old knob and timer dial. I replaced all the parts with the new ones and used pliers to reinstall the clip. The teeth on the new knob engage to select the cycle. https://www.youtube.com/watch?v=cQwLtRcHx9k Read more

I removed the dial knob and plate as instructed by the video, removed the front panel of the washer to access the switch. I found the plastic molded bracket that the timer rests on to be broken and the tab on the timer where it is attached by a screw to be broken. I ordered a replacement switch, dial and knob. When it arrived I replaced the parts as instructed, but I had to use super glue to hold the new switch in place due to the support tab on the washer panel being broken off. After letting... Read more

The video was very helpful. the hardest part is getting off old rusted parts. I had to use a hacksaw to remove one of the old clamps. I had to open the bottom of the washing machine to remove of the other clamp. Putting the new parts on was easy. Getting everything apart was a challenge. Putting the new parts on was an easy 5 minute job. Read more

Planning to spend hundreds on a new washer and was pleased to discover the agitator coupling was the only thing wrong. Very easy repair. The only additional feature we would have liked was a softener dispenser. Located a GE model of the same genre that used the same coupler and took the leap to get the agitator and dispenser cup for this model (WJRR4170). Replaced the old agitator with new one and dispenser cup. Worked perfectly! We now have a washer with dispenser that works great and saved... Read more

I have a 14 year old GE washing machine that had been making a lot of noise while running but had eventually just stopped flat. The agitator and spin cycle would not run. I found this site and made excellent use of all the repair videos to study about my issue. I put in my machine model number and I Immediately was able to start honing in on what my problem could be from website advice about popular repair parts, stories others had shared about their similar machine issues and watching videos,... Read more

Replaced lid switch and lid magnet. Took just a little longer then 20 minutes as I had to splice in the new lid switch as it wasn't one that was a clip in, it was hard wired in. Read more

I have a 14 year old GE washing machine that had been making a lot of noise while running but had eventually just stopped flat. The agitator and spin cycle would not run. I found this site and made excellent use of all the repair videos to study about my issue. I put in my machine model number and I Immediately was able to start honing in on what my problem could be from website advice about popular repair parts, stories others had shared about their similar machine issues and watching videos,... Read more

I have a 14 year old GE washing machine that had been making a lot of noise while running but had eventually just stopped flat. The agitator and spin cycle would not run. I found this site and made excellent use of all the repair videos to study about my issue. I put in my machine model number and I Immediately was able to start honing in on what my problem could be from website advice about popular repair parts, stories others had shared about their similar machine issues and watching videos,... Read more

Motor control board was flashing 4 times, indicating that the mode shifter had an error. I disconnected the mode shifter's wire from the controller and measured the resistance between the 2 leads with an ohmmeter. Since the reading was infinite, that meant that the mode shifter coil or in-line thermal sensor was electrically open, i.e. bad. As this fix is near a complete tear-down of the washing machine, here are a few tips I discovered. 1) the hub nut is difficult to remove and you need a... Read more

Replaced the hose and water inlet. Part #: AP3189243 (WH41X10077). This connects the solenoid valves to bring water into the tub. Read more

My husband put the new agitator together and it is working great, thanks for having all the part I needed. Susie Read more

I have a 14 year old GE washing machine that had been making a lot of noise while running but had eventually just stopped flat. The agitator and spin cycle would not run. I found this site and made excellent use of all the repair videos to study about my issue. I put in my machine model number and I Immediately was able to start honing in on what my problem could be from website advice about popular repair parts, stories others had shared about their similar machine issues and watching videos,... Read more