Gfwn1oooliww Parts

Note: Sold as 1 shock. Damper pin is part# WH01X10261.

This suspension spring supports and stabilizes the washer tub, controlling movement during wash and spin. Replacing a weak or broken spring helps restore balance, reduce vibration, and prevent the tub from leaning or striking the cabinet.

• Supports the tub assembly within the cabinet and carries load
• Limits tub motion to reduce shaking and out-of-balance interruptions
• A stretched or broken spring can cause excessive vibration, banging, or a low/leaning tub
• Visual signs include broken coils or uneven tub height

• Disconnect power; turn off water and move the washer for safe access
• Springs are under tension—support the tub and wear hand/eye protection
• Note the original spring's location and orientation; reinstall in the same position
• After replacement, ensure the tub sits level and clears the cabinet on all sides

This is a gasket made for use with washing machines. This particular gasket fits between the washer tub and the door, forming a seal that prevents leaks. Over time, gaskets are subject to wear and tear that can cause them to become brittle, rip, tear, warp, or otherwise be rendered ineffective. If the user notices that there is water leaking from the washing machine door during use, or the gasket is displaying visible signs of wear and tear, replace this part immediately. No tools are required to install this gasket.This gasket is manufactured from high-quality, durable, non-corrosive materials to ensure the best possible quality. This part is manufactured by General Electric and has been sourced directly from the manufacturer. It is sold individually and compatible with washers from General Electric, Hotpoint, and RCA.

This outer door gasket clamp secures the washer's door boot to the front panel, keeping the seal tight around the door opening to help prevent leaks and keep the gasket seated during operation.

• Holds the outer lip of the door gasket (boot) against the front panel
• Helps maintain a watertight seal at the door opening
• Replace if the clamp is bent, stretched, broken, or missing
• Symptoms include the boot slipping off, water leaking at the front, or a loose gasket

• Disconnect power and wear cut-resistant gloves for safety.
• Open the door, gently pull back the gasket, and remove the old outer clamp.
• Ensure the gasket is fully seated on the front panel lip, then install the new clamp evenly around the opening.
• After installation, run a short cycle and check for leaks around the door.

Hinge Leaf secures a refrigerator or freezer door at the hinge point, providing a stable mounting surface that helps the door stay aligned and open/close smoothly — reducing sag and uneven gaps. What it does:

• Secures the hinge pin and fastens the door to the cabinet at the hinge location.
• Maintains door alignment to help ensure even sealing and proper closing.
• Helps correct common door problems like sagging, binding, or uneven gaps.
• Works with existing hinge hardware to restore hinge stability when the leaf is worn or damaged.

• Disconnect power (unplug or switch off circuit) and remove food/contents from the door before starting.
• Support the door while removing hinge fasteners to prevent the door from dropping or shifting.
• Use appropriate hand tools and keep original screws/hardware unless replacing.

This interface board mounts behind the washer's control panel and reads your button/knob inputs. Replacing a failed UI board restores responsive controls, correct cycle selection, and indicator lights so the washer can start and run as expected.

• Interprets user inputs from the control panel and selector(s)
• Communicates selections to the main control to run chosen cycles/options
• Drives status lights or display during operation
• Typical failure symptoms: unresponsive controls, lights/display not illuminating, cannot start or change cycles, intermittent/erratic inputs

• Disconnect power to the appliance before servicing; follow ESD precautions and handle the board by the edges
• Access the board by removing the console/control panel; note screw locations and take photos of wiring
• Transfer wire connectors one at a time to the new board to prevent miswiring; ensure all harnesses are fully seated
• Reassemble the console and restore power; test all buttons and indicators

This outside drain hose directs wastewater from your washer to the household drain. Replace a cracked, kinked, or leaking hose to stop leaks and restore reliable draining at the end of each cycle.

• Routes discharge water from the drain pump to a standpipe, laundry tub, or sink
• Helps maintain proper flow during drain/spin to prevent backups
• Common signs of failure: water leaking behind the washer, slow or incomplete draining, or drain-related error messages
• Visual clues include cracks, pinholes, bulges, or severe kinks

• Disconnect power and water; pull the washer forward for access and place towels/bucket as needed
• Note hose routing and connection points; release clamps and remove the old hose
• Fully seat the new hose; reuse existing clamps/hangers as required. Route without kinks and maintain proper standpipe height
• Run a test drain/rinse and check all connections for leaks

The Washer Door Glass is an OEM part for GE washers. This glass serves as a protective barrier while allowing you to observe the washing process inside the machine. The door glass is designed to withstand the rigors of regular use and maintain transparency for a clear view of your laundry.

A bad door glass can occur due to accidental breakage or cracks over time. If you notice signs of damage, such as shattered or missing pieces, it may be time to replace the door glass.

Symptoms of a bad door glass include:

• Shattered or broken glass
• Visible cracks or chips
• Inability to see through the glass

Restore the function of your GE washer by replacing the damaged door glass with this genuine part. This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances.

The TUB SEAL is an OEM component specifically designed for GE washers. It is a rubber gasket located between the inner and outer wash tubs designed to prevent leaks. During cycles, the seal withstands contact with fast spinning and surging water pressure to maintain a watertight barrier. 

Symptoms of a bad tub seal include: 

• Puddles, drips, or leaks visible beneath the unit during or after cycles
• Excess moisture trapped between the inner and outer tubs
• Mineral or soap film buildup indicating escaping water 

Causes can be cracks developing from age and repetitive flexing during cycles, or deformities in the rubber preventing proper compression.

Replace yours today with this genuine OEM GE part to ensure a dependable water containment solution. This GE replacement part is compatible with Hotpoint, RCA, and select Kenmore models.

This inside gasket clamp secures the appliance's inner door gasket, helping maintain a tight seal and reduce leaks. It's a small but important retaining clip used where the gasket meets the door or opening. What it does:

• Holds the inner edge of the door or tub gasket in place to keep the seal seated
• Helps prevent water or air from leaking around the door during operation
• Restores proper gasket alignment when a worn or broken clamp allows the gasket to shift
• Works as a replacement for damaged or missing gasket retaining clamps

• One gasket inside clamp (single clamp as shipped)

• Recommended to inspect the gasket and surrounding trim for wear before installing the clamp
• Remove power and water (if applicable) to the appliance before servicing
• May require basic hand tools and careful prying to remove the old clamp and seat the new one
• If gasket is damaged or torn, replace the gasket as well for a reliable seal

This stacking kit secures a compatible dryer to a matching washer to create a safe, space-saving stacked laundry configuration. It helps stabilize the dryer and reduces movement during use for a more reliable setup. What it does:

• Provides brackets and mounting hardware to fasten the dryer to the washer
• Helps prevent the dryer from shifting or tipping when the washer is running
• Improves overall stability of stacked laundry appliances during normal operation
• Reduces vibration-related movement that can cause noise or misalignment

• Disconnect power to both appliances before installing and follow all manufacturer instructions
• Use only on compatible washer/dryer pairs
• Tighten hardware securely but avoid overtightening; follow torque guidance in OEM instructions

This motor assembly kit replaces a worn or failed motor to restore proper mechanical drive and motion in the appliance. It's a direct-fit replacement designed to match the original assembly's form and function. What it does:

• Replaces the appliance's motor assembly to restore spinning, stirring, or drive motion
• Stops symptoms like no movement, intermittent operation, or unusual humming from the motor area
• Restores correct mechanical linkage between the motor and driven components
• Matches OEM fit and mounting points to simplify replacement

• One motor assembly kit (single complete motor assembly)

• Turn off power to the appliance at the breaker or unplug before beginning any repair
• Follow OEM disassembly steps to access the motor area; keep fasteners and small parts organized
• Handle electrical connectors carefully; wiring matches diagrams before re-energizing

This siphon pipe is a washer drain component that forms part of the air-break assembly. It helps prevent unintended siphoning and backflow so the tub drains correctly without pulling water back in or continuously draining. What it does:

• Provides the pipe section of the washer's siphon break/air gap
• Maintains airflow to stop siphoning and backflow during drain and spin
• Supports consistent, complete draining
• Typical failure signs: leaks near the siphon break, cracking, or water draining back into the tub

• Includes one siphon pipe

• Disconnect power and turn off water before servicing
• Expect some residual water; have towels or a pan ready
• Note hose routing; transfer any clamps/fittings from the old pipe and seat connections fully
• After reassembly, run a brief fill/drain to check for leaks and proper draining

This is a replacement ST4-16 sheet-metal mounting screw used to secure panels and small components on compatible appliances. It restores proper fit and prevents loose or rattling parts for a secure repair. What it does:

• Fastens trim, access panels, brackets and small components to appliance chassis
• Replaces missing, stripped or damaged screws that cause loose panels or vibration
• Provides correct thread and length for original mounting locations (ST4-16 size)
• Helps maintain safe, gap-free panel alignment for normal operation

• Use the same screw size and thread type as the original; do not over-torque
• If thread engagement is poor, inspect mating hole for damage before reuse
• Wear safety glasses and disconnect power to the appliance before working on panels
• If multiple screws are missing or hardware is corroded, replace all like-for-like fasteners

This M5-16 metric machine screw secures service panels and internal components in compatible appliances, providing reliable fastening for repair and replacement. Use the correct screw to restore fit and function after disassembly or part replacement. What it does

• Fastens panels, brackets, and components where an M5 x 16 mm machine screw is specified
• Restores secure attachment after repair or replacement of parts
• Helps eliminate rattles, loose panels, or misaligned parts when the correct screw is used
• Small, corrosion-resistant finish (typical for appliance screws) for lasting hold

• One M5-16 machine screw

• Use the correct sized M5 driver or hex bit to avoid stripping the head
• Tighten until snug; do not over-torque to prevent thread or component damage
• Disconnect power and follow appliance safety procedures before accessing internal parts
• If the original screw had washers or clips, reuse them or replace with equivalent hardware

This electronic main control replaces the appliance's central circuit board to restore normal operation and user interface response. It manages program selection, timing, and communication between sensors and motors for proper cycles. What it does:

• Receives user input and runs the appliance's programmed cycles
• Sends signals to motors, valves, heaters, and sensors to start/stop functions
• Can correct failures like unresponsive controls, incorrect cycles, or error-code behavior when board is faulty
• Helps restore display and touchpad responsiveness when the issue is electronic control failure

• Disconnect all power (unplug or shut off breaker) before starting any work
• Take photos of wiring and connector positions before removal to ensure correct reassembly
• Handle the board by edges and avoid touching circuitry; protect against static discharge