Gsc23lsrc Ss Parts

This crisper cover glass is the removable glass panel that fits into the crisper pan cover. It restores a flat, sturdy surface above the drawers and helps keep small spills contained for easier cleanup.

• Forms the shelf surface above the crisper drawers within the cover frame
• Helps contain minor spills and supports stored food items
• Replace if cracked, shattered, bowed, or missing
• Symptoms include broken glass, items tipping, or drawers rubbing the cover

• Disconnect power and clear the shelf area before starting
• Remove crisper drawers and lift off the cover frame to access the glass
• Carefully remove the old panel and seat the new glass fully in the frame channels
• Reinstall the cover and drawers, then restore power

This defrost heater and bracket assembly melts frost from the evaporator during the automatic defrost cycle, restoring airflow and stable temperatures so your refrigerator and freezer cool as designed. What it does:

• Heats the evaporator coil at set intervals to clear frost and ice
• Keeps air passages open for consistent temperatures and efficient cooling
• Helps prevent excessive run times and ice buildup on the freezer back wall
• Failure signs can include heavy frost accumulation, weak/uneven cooling, or fan noise from ice

• One defrost heater pre-mounted to its bracket

• Disconnect power before servicing; wear cut-resistant gloves
• Access the evaporator behind the freezer's rear panel; safely defrost built-up ice before removal
• Note/photograph wire routing and connections; transfer like-for-like
• Avoid damaging evaporator fins and ensure the heater sits in the original position without touching plastic components

This ice dispenser auger drive mounts on the dispenser motor shaft and engages the ice bucket auger. Replacing a worn or stripped drive restores the connection so your refrigerator can move ice smoothly to the chute.

• Couples the dispenser motor to the ice-bin auger to rotate and move ice toward the chute
• On models with crushers, also drives the crushing mechanism
• Worn or rounded splines can cause little or no ice dispensing even though the motor runs
• May produce clicking/grinding noises from the door during dispense
• Visible cracking or play at the coupling indicates replacement is needed

• Unplug the refrigerator and shut off water before servicing
• Remove the ice bin to access the dispenser motor shaft in the freezer door
• Note the orientation; remove the old drive and seat the new drive fully on the shaft, transferring any original hardware if present
• Reinstall the ice bin, restore power, and test ice dispense

Water line from water valve up to icemaker fill tube.

The recess door retainer secures the dispenser's ice chute flapper in the refrigerator door. Replacing a cracked or missing retainer restores proper flapper pivot and sealing to help reduce frost buildup and air leaks around the dispenser.

• Holds the recess/ice door on its pivot within the dispenser assembly
• Helps the flapper close fully to seal the ice chute
• Restores smooth open/close action of the dispenser door
• Common symptoms: loose or fallen flapper, poor chute seal, frost or condensation in the dispenser area, and ice clumping near the chute

• Unplug the refrigerator before servicing the dispenser
• Carefully remove the dispenser bezel/control panel to access the ice chute door assembly
• Note spring orientation and retainer position; transfer components to the new retainer
• Verify flapper movement and seal before reassembly and restoring power

The Freezer Light Cover is an OEM replacement part for GE refrigerators designed to protect the light bulb in the freezer compartment from any potential damage or breaks. It helps maintain a safe and well-lit freezer environment, making it easier to locate and retrieve items.

A bad freezer light shield cover can occur due to regular wear and tear or accidental damage. If you notice symptoms such as a flickering or dim freezer light, or if the light bulb is exposed and vulnerable, it may indicate a need to replace this part.

Symptoms of a bad freezer light cover include:

• Flickering or dim freezer light
• Exposed or broken light bulb
• Insufficient lighting 

Restore lighting in your freezer by replacing the faulty freezer light cover with this genuine OEM part.

This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

This pan frame assembly forms the cover over a refrigerator storage drawer and supports the glass shelf above. Replace a cracked or warped frame to restore smooth drawer operation and a sturdy, level storage surface.

• Supports and aligns the drawer(s) beneath while carrying the load of the shelf above
• Restores a stable, level surface when the original frame is cracked, bowed, or broken
• Helps drawers open and close smoothly when tracks and stops are intact
• Common symptoms: shelf sagging, wobble, broken corners/tabs, drawer binding or misalignment

• Disconnect power and remove food from the affected shelf area
• Carefully remove the glass insert and drawer(s); handle tempered glass with care
• Lift out the old frame; seat the new frame fully on its supports and ensure tabs/slots are engaged
• Reinstall the glass and drawer(s); verify smooth drawer travel and that the shelf sits level

This fixed freezer shelf restores a sturdy, level storage surface in the freezer compartment. Replace a broken or missing shelf to regain organization, correct spacing, and full storage capacity.

• Provides a fixed-position storage surface inside the freezer
• Helps keep items level, organized, and easy to access
• Restores proper spacing with adjacent shelves, drawers, or baskets
• Replaces a cracked, warped, or missing shelf

• Disconnect power before servicing; wear gloves to protect hands
• Empty the area, then align the shelf with the side-wall slots or supports
• Slide or place the shelf into the supports until fully seated and level
• Distribute weight evenly and avoid overloading after installation

This replacement screw fastens refrigerator components securely, restoring a tight, rattle-free fit when original hardware is missing, stripped, or corroded. Use it to secure panels, brackets, or trim and keep parts properly aligned.

• Secures panels, brackets, covers, or trim in place
• Helps maintain correct alignment of components and hardware
• Reduces vibration and rattling caused by loose or missing screws
• Replaces lost, rusted, or stripped screws

• Unplug the refrigerator and turn off water supply if working near water components
• Match thread and length to the removed fastener; hand-start threads to avoid cross-threading
• Tighten snugly; do not overtighten into plastic or thin sheet metal
• Keep track of any spacers or washers reused from the original assembly

This replacement bottom door hinge and pin assembly fits refrigerators. The lower hinge supports the door's weight and provides the pivot point, restoring smooth swing and proper alignment for a reliable close and consistent gasket seal.

• Serves as the door's lower pivot and load-bearing support
• Maintains alignment so the gasket seals correctly
• Restores smooth opening and closing after hinge/pin wear
• Common symptoms: door sagging or dragging, popping/squeaking at the hinge, gaps or poor sealing, door not staying closed

• Disconnect power and remove items from the door before servicing
• Support the door, remove bottom hinge fasteners, and lift the door off
• Position the new hinge and transfer any spacers/shims as found
• Reinstall the door, tighten hardware, and verify alignment and gasket seal

This refrigerator dispenser funnel extension attaches at the front of the dispenser to better direct the stream into your cup. Replacing a cracked or missing extension reduces splashing and helps keep the dispenser area cleaner.

• Directs the dispenser stream to help prevent splashes and drips
• Extends the spout area for easier filling of glasses and bottles
• Restores fit and appearance when the original is cracked, warped, or missing
• Common symptoms: water splashing at the dispenser, loose/broken piece, water running down the door

• Unplug the refrigerator and shut off water before servicing the dispenser area
• Remove the old extension by releasing its retaining tabs, if present
• Align the new extension with the slots and press until it snaps securely into place
• Restore power/water and test the dispenser to verify proper flow and a secure fit

This dairy compartment is the dedicated storage bin on your refrigerator's fresh food door for butter and other small items. Replacing a cracked or missing dairy bin restores secure, convenient door storage and keeps contents organized.

• Mounts on the refrigerator door to hold butter and small items
• Helps keep contents contained during normal door opening and closing
• Restores proper storage when the original bin is cracked, warped, or missing
• Addresses issues like broken tabs or a bin that won't stay attached

• Remove the old bin by lifting it up and out of the door liner channels
• Align the new bin with the door slots or hooks and press/snap into place
• If your model uses screws or retainers, transfer and reuse them
• Handle plastic tabs gently and ensure the bin is fully seated before loading

This is a grommet and it is intended for use on refrigerators and freezers. This is a genuine replacement part made by General Electric. A new grommet might be needed if the current one is visibly worn out or damaged in any way. If there are noises from vibration coming from the lower back area of the fridge there might be need for a new grommet. This is an OEM part sourced directly from the manufacturer, and it is sold individually. It is compatible with refrigerators and freezers, or units with a compressor and is made by General Electric.

This foam insulation wraps the refrigerator's water reservoir to reduce sweating and help prevent freezing, keeping dispenser flow consistent and the fresh food compartment dry. Replace if the original insulation is torn, crushed, or missing. What it does:

• Insulates the water reservoir to help maintain a stable temperature
• Helps prevent the reservoir from freezing, which can slow or stop dispenser flow
• Reduces condensation that can drip or puddle inside the refrigerator
• Restores proper cushioning and protection around the tank

• 1 foam insulation piece for the water tank

• Unplug the refrigerator and shut off the water supply before servicing
• Remove shelves/drawers to access the water reservoir area
• Carefully remove the old insulation; avoid stressing or puncturing the reservoir and tubing
• Fit the new foam snugly around the tank, reassemble, restore power/water, and check for leaks and dispenser flow

This screw fastens appliance panels, brackets, and trim so parts stay secure and aligned. Replace a missing, stripped, or rusty screw to stop rattles and restore a tight, factory fit.

• Secures covers, brackets, and trim to the appliance cabinet or liner
• Replaces missing, stripped, or corroded hardware
• Helps reduce vibration noise and loose or misaligned parts
• Maintains proper fit of guards, kickplates, or internal panels

• Disconnect power; turn off water supply if working near water lines
• Match to the original fastener to size and thread
• Start threads by hand to avoid cross-threading; tighten snugly, not excessively
• If threading into plastic, avoid overtightening to prevent damage