Gsd494ozooss Parts

Size: 8-18 x 7/8 inch.

This is a genuine replacement screw used to secure components and panels on compatible GE appliances. It restores proper fit and prevents rattling or loose parts for safe, reliable operation. What it does:

• Secures panels, brackets, or internal components to maintain proper alignment
• Stops rattling or vibration caused by loose fasteners
• Replaces missing, stripped, or damaged screws to restore safe operation
• Helps maintain seals and clearances by holding parts firmly in place

• Screw

• Disconnect power to the appliance before starting any repair
• Use the correct screwdriver or bit to avoid stripping the head
• Do not overtighten; snug until secure to prevent damage to components
• Keep removed fasteners organized to ensure correct reassembly

This harness jump is a short jumper wire assembly used to reconnect two electrical terminals, restoring an intended circuit path for proper operation. It offers a direct, serviceable way to replace a broken or missing factory jumper. What it does:

• Bridges two terminals to complete a circuit when the original jumper is damaged or removed
• Helps restore power or signal to control components that rely on the jumper connection
• Commonly used in control, terminal block, or switch assemblies where a short wire link is required
• Can resolve symptoms such as intermittent or no power to a circuit, or a component not receiving a control signal

• One harness jump (single jumper wire assembly)

• High-level replacement only; ensure power is disconnected at the breaker or unplug the appliance before servicing
• Match connector style and terminal orientation to the original jumper before installing
• Inspect surrounding wiring and terminals for damage or corrosion; replace if needed

A stainless-steel #6-20 screw (1/2" length) used to fasten appliance panels and components securely. Durable corrosion-resistant finish helps maintain a tight fit and long-lasting hold in wet or humid areas. What it does:

• Fastens trim, brackets, panels, and internal components where a #6-20 x 1/2" screw is specified
• Provides a corrosion-resistant connection for areas exposed to moisture
• Restores loose or missing fasteners that cause rattling or misalignment
• Matches OEM thread and length for proper fit and function

• One stainless steel #6-20 x 1/2" screw

• Turn power off and unplug appliance before servicing
• Use the correct screwdriver or driver bit to avoid stripping the head
• Do not overtighten; stop when the component is snug and aligned
• Replace any additional damaged fasteners with matching OEM screws

The spray arm assembly distributes pressurized wash water through its jets and rotates to clean dishes. If it's cracked, clogged, or not turning freely, replacing it restores proper spray coverage and cleaning performance.

• Directs water through jet openings to wash dishes throughout the tub
• Rotates by water force for even spray coverage
• Common symptoms: poor cleaning results, arm not spinning, visible cracks/warping, or clogged holes
• May cause unusual knocking if the arm is loose or contacting items

• Disconnect power and turn off the water supply before servicing
• Remove the lower rack; release the existing spray arm from the center retainer (method varies by model)
• Clear any debris from the pump outlet and seating surface
• Seat the new arm fully and ensure it spins freely before running a test cycle

This upper dispenser trim—commonly called the top tower—replaces the visible upper cover at the refrigerator dispenser area to restore appearance and proper fit. It protects internal dispenser components and keeps the dispenser edges clean and aligned. What it does

• Covers and protects the upper portion of the dispenser tower and its internal components
• Helps maintain a consistent, finished look at the dispenser opening
• Prevents dirt and moisture from reaching internal dispenser parts
• Can reduce rubbing or misalignment of the dispenser fixture that can cause noise or wear

• One upper dispenser trim (top tower) as shown

• Remove power to the appliance before starting work to avoid electrical hazards
• Typically secures with clips or a few screws—gentle prying with a trim tool may be required
• Inspect adjacent trim and fasteners for wear and replace as needed for a proper fit

This is a replacement washer drive motor that powers the tub to spin and agitate, restoring normal wash and spin cycles. Fits specified GE top-load washers and matches OEM form and function. What it does

• Spins the wash tub to perform spin cycles and remove water
• Powers the agitation/oscillation action during wash cycles
• Commonly replaced when the washer won't spin, won't agitate, or hums without turning
• Helps eliminate intermittent power-to-motor issues when motor failure is the root cause

• One replacement drive motor

• Disconnect power before starting any repair to avoid electric shock
• May require removing the washer cabinet or access panels and detaching the old motor wiring and mounting screws
• Handle carefully — support the tub/drum as needed during motor removal and reinstallation

This switch interlock assembly secures the appliance door and completes the electrical circuit so the unit can start and run safely. Replacing a worn interlock restores reliable door sensing and helps ensure normal cycle operation. What it does:

• Detects and holds the door/lid closed so the appliance will start
• Completes the electrical pathway for motor and control circuits
• Prevents operation when the door is open or not fully latched
• Can stop mid-cycle or prevent starting when the interlock fails

• One switch interlock assembly

• Disconnect power (unplug or switch off the breaker) before replacing the part
• Handle mounting screws and wiring harness carefully; match connector orientation when reinstalling
• Verify door alignment and latch function before restoring power

This switch sensor is a direct-replacement sensing device that detects the position/state of a moving component and sends that signal to the appliance control for reliable operation. It restores correct sensing when the original fails. What it does:

• Detects and reports a component's open/closed or engaged/disengaged position to the control
• Helps the appliance start and change cycles only when the mechanism is in the correct position
• Can resolve symptoms such as no response from the control, intermittent operation, or cycles that won't advance
• Provides a direct electrical/mechanical interface between the moving part and the control system

• One switch sensor

• Disconnect power to the appliance before starting any repair
• Match this part number to the failed sensor before installing
• Handle wiring and connectors carefully; avoid forcing tabs or pins
• Test operation after installation and restore power only when all connections are secure

This gripper holds stemware securely in the dishwasher stemware rack to help prevent glasses from tipping, shifting, or breaking during a wash cycle. It replaces worn or broken stemware clips so racks can secure the stems of wine and other stemmed glasses. What it does:

• Clips onto the dishwasher stemware rack to hold glass stems steady during cycles
• Helps reduce glass-to-glass contact and chipping from shifting items
• Restores proper rack functionality when original grippers are missing or damaged
• Fits into the rack's designated stemware openings for a snug hold

• One gripper stemware clip (single piece)

• High-level replacement — typically snaps into the rack's stemware slot without tools
• Inspect the rack for damage; replace any additional broken clips as needed
• Disconnect power to the appliance before doing any work that requires access inside the dishwasher
• Handle glass carefully to avoid breakage during removal and reinstallation

This support calrod assembly secures and positions the oven/range heating element so it heats evenly and stays stable during operation. Replaces a worn or damaged support to restore proper element alignment and reduce rubbing or sparking. What it does:

• Holds the tubular heating element in the correct orientation inside the oven or range
• Prevents the element from sagging, contacting interior surfaces, or vibrating during use
• Helps maintain consistent heating performance and reduces risk of element wear
• Common symptom: element rubbing, touching oven walls, or uneven heat distribution

• One support calrod assembly

• Disconnect power at the breaker or unplug the appliance before starting any repair
• Handle heating elements and support parts carefully to avoid bending or damaging the element
• Follow OEM service instructions for removal and reassembly; verify correct element alignment before restoring power