Gsd6200g00bb2230f00ww Parts

The Middle Spray Arm Kit is an OEM replacement part specific to GE dishwashers. It contains the rotating center arm component that helps distribute water, dishwasher detergent, and moisture across the middle rack shelves for enhanced cleaning.

Causes of a bad middle spray arm can include clogged spray holes inhibiting proper water coverage, worn ball bearings reducing spray force, or broken or missing spray arm attachment clips.

Symptoms of a bad middle spray arm include:

• Items on middle racks not receiving sufficient cleaning
• Dried food or soap scum buildup is visible on rack shelves and dishes
• The arm fails to rotate or spin during cycles
• Detached spray arm is no longer connected to the dishwasher tub

This OEM GE replacement is compatible with many GE, Hotpoint, and Profile dishwasher models.

The Fine Filter Hub Nut is an OEM part for GE dishwashers. It secures the fine filter in place, ensuring that debris and food particles are effectively filtered out during the wash cycle, preventing them from re-entering the dishwasher tub.

Causes of a bad fine filter hub nut can include wear and tear from regular use, damage from over-tightening, or cracking due to impact. A faulty hub nut can lead to improper filtration, causing debris to circulate and potentially clog the dishwasher.

Symptoms of a bad Fine Filter Hub Nut include:

• Poor cleaning results with food particles left on dishes
• Unusual noises during the wash cycle
• The filter becoming loose or not staying in place

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This dishwasher float sits in the tub and works with the float switch to control the fill level and prevent overfilling. Replace it if cracked or sticking to restore reliable water level control and help avoid leaks.

• Rises with the water level to trigger the float switch and stop filling at the correct point
• Helps prevent overfilling and door leaks
• Common symptoms of a damaged or obstructed float include continuous filling, overfill/leaks, or no/insufficient fill
• Restores consistent water level sensing when the original float is worn or missing

• Disconnect power and turn off the water supply
• Open the door and remove the lower rack
• Remove the float cover; pull the old float straight up and clear any debris from the well
• Insert the new float and verify free up-and-down movement before reassembly and testing

This fill funnel gasket seals the water-inlet funnel where water enters the dishwasher tub. Replacing a worn seal helps prevent drips at the inlet and keeps incoming water directed into the tub during the fill cycle.

• Provides a watertight seal between the fill funnel and tub wall
• Helps prevent leaks from the inlet area and under the toe-kick
• Directs incoming water properly into the tub during fill
• Replace if the gasket is cracked, deformed, or leaking

• Disconnect power and turn off the water supply before servicing
• Access the fill funnel area; remove the old gasket and clean the sealing surfaces
• Seat the new gasket evenly and ensure the funnel fully engages the opening
• Reassemble and run a short fill to check for leaks

This dome float is the replacement water-level float that helps the appliance sense and control the tub's water level, restoring reliable fill and shutoff behavior. Use this OEM-fit float when the original is cracked, stuck, or missing. What it does:

• Moves with rising and falling water to actuate the water-level mechanism and help prevent overfilling.
• Can reduce symptoms such as improper fill levels, continuous filling, or intermittent fill shutoff when the existing float is damaged or obstructed.
• Works as part of the washer's water sensing system—does not include electronic switches or housings unless shown.

• Disconnect power and unplug the appliance before starting any repair.
• Access may require removing the washer top or cabinet; follow your model's service instructions.
• Inspect surrounding hoses and clips; replace any damaged components and ensure the float moves freely.

This flapper vent is the replacement exhaust flap that helps control dryer airflow and keeps outside air, pests and debris from entering the vent when the dryer is off. Fits many GE dryer exhaust housings. What it does

• Opens during dryer operation to let moist air escape and closes when the dryer is off to block backdrafts.
• Restores proper airflow when a damaged or stuck flap is preventing venting.
• Helps reduce outside odors, drafts and pest entry through the exhaust opening.
• Works as a simple mechanical replacement—no electrical connections.

• Disconnect the dryer from power and, if applicable, turn off gas before servicing.
• Access the exterior vent or the dryer exhaust housing; replacement typically secures with screws or snaps into the vent housing.
• Inspect and clean the vent duct and housing before installing the new flap to ensure proper operation.

This is a replacement fastener screw used to secure panels and components on compatible appliances, restoring proper fit and reducing movement. It's a simple, direct replacement when an original screw is missing or damaged. What it does:

• Secures access panels, covers, or internal components to prevent rattling and movement
• Helps maintain proper alignment of parts so doors and panels close correctly
• Replaces missing, stripped, or broken screws that can cause loose parts or noise
• Restores the appliance's original fit where a matching OEM fastener is required

• One replacement screw

• Turn off and unplug the appliance before starting any repair
• Use the correct driver and avoid over-tightening to prevent stripping threads
• If the original screw was holding electrical components, ensure power is disconnected and follow OEM safety instructions

 The Upper Arm Spray Assembly is an OEM part for GE dishwashers. It is responsible for distributing water evenly throughout the dishwasher during the cleaning cycle, ensuring all dishes are thoroughly cleaned. The arm measures approximately 11 inches long.

You should replace the upper arm spray assembly if it becomes clogged, damaged, or worn out. Causes of a bad spray assembly can include mineral buildup from hard water, food particles blocking the spray holes, or physical damage such as cracks or breaks.

Symptoms of a bad upper arm spray assembly include:

• Poor cleaning performance, with dishes coming out dirty
• Uneven water distribution inside the dishwasher
• Visible cracks or blockages in the spray arm
• Unusual noises during the wash cycle

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Upper Spray Arm Bearing is an OEM part for GE dishwashers. It supports the upper spray arm, allowing it to rotate smoothly and distribute water evenly throughout the dishwasher. This ensures that all dishes receive a thorough cleaning during each cycle.

Over time, the upper spray arm bearing can wear out or become damaged. Causes of a bad bearing can include repeated use, mineral buildup from hard water, or physical damage due to mishandling.

Symptoms of a bad Upper Spray Arm Bearing include:

• The upper spray arm not rotating properly
• Ineffective cleaning of dishes on the upper rack
• Unusual noises during the wash cycle

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Door Interlock Switch Assembly is an OEM part for GE dishwashers. It is designed to ensure the dishwasher door is securely closed before the wash cycle begins, preventing leaks and ensuring the appliance operates safely.

Causes of a bad interlock switch can include wear and tear from frequent use, electrical issues, or physical damage to the switch or its housing. A malfunctioning switch can prevent the dishwasher from starting or cause it to stop mid-cycle.

Symptoms of a bad door interlock switch assembly include:

• Dishwasher not starting
• Interruption of wash cycles
• Door not latching securely
• Error codes related to door latch issues

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Flood Switch Assembly is an OEM part for GE dishwashers. This part detects water levels and prevent overfilling by shutting off the water supply if a potential flood condition is detected. 

Causes of a bad flood switch assembly can include electrical failures, wear and tear over time, or damage from water exposure. 

Symptoms of a bad flood switch assembly include:

• The dishwasher not filling with water properly
• The dishwasher overfilling or leaking
• Error codes related to water levels
• The dishwasher not starting or stopping mid-cycle

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The GE latch handle is an OEM replacement part responsible for allowing the opening and closing of the dishwasher door. Located on the inner door panel, this part ensures that the dishwasher door latches securely when the machine is in operation, preventing any leaks or disruptions in the cleaning process. Additionally, it provides a convenient means for users to open and close the dishwasher, allowing easy access to load and unload dishes.

This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances.

This part fixes the following symptoms

• Difficulty in opening or closing the dishwasher door.
• The door not staying securely closed during a wash cycle.
• Visible damage to the latch handle.