Gsh22jsdd Ss Parts

The recess door retainer secures the dispenser's ice chute flapper in the refrigerator door. Replacing a cracked or missing retainer restores proper flapper pivot and sealing to help reduce frost buildup and air leaks around the dispenser.

• Holds the recess/ice door on its pivot within the dispenser assembly
• Helps the flapper close fully to seal the ice chute
• Restores smooth open/close action of the dispenser door
• Common symptoms: loose or fallen flapper, poor chute seal, frost or condensation in the dispenser area, and ice clumping near the chute

• Unplug the refrigerator before servicing the dispenser
• Carefully remove the dispenser bezel/control panel to access the ice chute door assembly
• Note spring orientation and retainer position; transfer components to the new retainer
• Verify flapper movement and seal before reassembly and restoring power

Color: white. It measures about 15 inches wide by 1 inch deep.

Restore solid storage space with this fixed shelf module for your refrigerator. It replaces a damaged or missing shelf so you can organize groceries securely and use your fridge's capacity the way it was designed.

• Provides a stable, level surface for food and containers inside the refrigerator compartment
• Fixed, non-slide design stays in place once installed
• Factory-fit geometry helps prevent wobbling and tipping
• Typical symptoms: cracked or broken shelf, broken mounting tabs, shelf won't seat or sit level, missing shelf

• Remove items from the area and take out the old shelf; wear cut-resistant gloves and handle carefully
• Align the new shelf with the side supports/slots and lower or slide into place
• Verify the shelf is fully seated and level before loading items
• Disconnect power if working near interior lights or electrical components

This assembly meters cold air from the freezer into the fresh-food compartment and provides temperature feedback to the controls. Replacing a failing unit restores proper airflow and more stable, even cooling performance.

• Motorized damper door opens and closes to regulate airflow from the freezer; stuck-open can cause freezing near the vent, stuck-closed can leave the fresh-food section warm.
• Integrated thermistor senses compartment temperature and signals the control board; a failed sensor can cause erratic or inconsistent temperatures.
• Helps balance airflow between compartments to maintain set temperatures.
• Common clues include clicking/chattering from the damper area, weak or constant airflow, warm spots, or items freezing on upper shelves.

• Disconnect power before servicing.
• Access the damper through the fresh-food air duct; remove shelves and the duct cover as needed.
• Disconnect the wire harness; route and seat wiring and seals in the same positions during reassembly to prevent air leaks.
• Restore power and allow up to 24 hours for temperatures to stabilize.

The lower gasket shield is a guide that protects the refrigerator door gasket at the bottom edge, helping the door close smoothly and maintain an even, reliable seal to keep temperatures stable and moisture down. What it does:

• Protects the lower edge of the door gasket from wear and deformation
• Guides the gasket into place for a snug, even seal
• Helps reduce warm-air leaks that can cause condensation or frost
• Replaces cracked, missing, or warped shields that can lead to poor sealing

• Includes 1 lower gasket shield

• Disconnect power and open the door for safe access
• Remove any lower door bins if needed
• Gently pull back the gasket at the lower edge to expose the shield and fasteners
• Install the new shield, reseat the gasket fully, and verify the seal with a paper-slip test

Size: 8-18 AB TSQ 5/8 SS

This is a grommet and it is intended for use on refrigerators and freezers. This is a genuine replacement part made by General Electric. A new grommet might be needed if the current one is visibly worn out or damaged in any way. If there are noises from vibration coming from the lower back area of the fridge there might be need for a new grommet. This is an OEM part sourced directly from the manufacturer, and it is sold individually. It is compatible with refrigerators and freezers, or units with a compressor and is made by General Electric.

Front mounting grommet.

This compressor overload protects the refrigerator's compressor by cutting power if it overheats or draws excessive current. When it fails, the compressor may not start and the fridge can warm up while you hear repeated clicking from the rear.

• Opens the circuit to the compressor when temperature or amperage exceed design limits
• Helps prevent compressor motor damage from locked-rotor or overheating conditions
• Typical failure symptoms: compressor won't start, warm refrigerator/freezer, rhythmic clicking or buzzing near the compressor
• Physical clues: heat discoloration, cracked housing, or a loose internal rattle

• Unplug the refrigerator and allow the compressor area to cool before servicing
• Remove the rear access panel and the compressor start device cover
• Note wire locations; pull the old overload straight off the compressor terminal and transfer any wires; reinstall with the existing start relay as designed
• Seat fully on the terminal and reinstall the cover; replace any heat-damaged terminals or companion components if needed

This OEM part is a refrigerator dispenser interface. The dispenser interface is responsible for the main functions of the refrigerator, such as adjusting the temperature settings as well as the other functions that are displayed on the interface. If the refrigerator is no longer cooling efficiently, failing to maintain temperature, dispensing water, or the touchpad is unresponsive, the interface might need to be replaced. Thankfully, replacing this part is not a difficult process.To replace the old interface, make sure that all power to the refrigerator is turned off. Open the refrigerator door and remove the door panel of the interior of the refrigerator. Locate the old control board and remove the wire harnesses that connect to it. Take note of the wire connector's orientation and reinsert the wires to the new board. Snap the new interface back in place and reinstall the inner panel. This genuine replacement part is sold individually and is compatible with General Electric, Hotpoint, and RCA brand refrigerators.

This damper gasket seals the refrigerator air damper opening between the freezer and fresh food compartments to prevent air leaks and help maintain stable temperatures. A new seal supports proper airflow and helps reduce moisture or frost near the damper. What it does:

• Seals the perimeter of the air damper/baffle to prevent bypass air leaks
• Helps regulate airflow from freezer to refrigerator for consistent cooling
• Wear, flattening, or tears can lead to warm spots in the fresh food section
• May also contribute to condensation, frost, or whistling/draft at the damper cover

• 1 damper gasket

• Unplug the refrigerator before servicing
• Remove the interior damper cover/grille to access the damper; note gasket orientation
• Seat the new gasket evenly around the damper frame without stretching or twisting
• Reinstall cover, restore power, and verify airflow and door sealing

Includes 12 retainer rings.

Replacement diverter overflow that helps channel excess water away from the ice maker/water system to reduce pooling and leaks. Restores proper drainage so the refrigerator interior stays dry and operates as intended. What it does:

• Directs overflow or stray water from the ice maker/water area into the drain path
• Helps prevent water pooling or dripping inside the freezer or cabinet
• Use when you notice leaks, water pooling under shelves, or water coming from the dispenser/ice area

• Always disconnect power and shut off the water supply before starting any repair
• Removal of interior shelves/trim or access panels may be required to reach the diverter
• Handle plastic tabs and clips carefully to avoid breakage; replace any damaged fasteners

This cable clamp secures refrigerator wiring to the cabinet, keeping harnesses organized and protected. Replacing a missing or damaged clamp helps prevent chafing and vibration noise while maintaining proper clearance from fans and other moving components.

• Anchors wire harnesses in their designed routing
• Helps prevent insulation wear from rubbing or vibration
• Keeps wires clear of sharp edges and moving parts
• Common signs it's needed: missing/broken clamp, loose or dangling wires, or new rattling/buzzing noises

• Disconnect power before servicing
• Access the clamp location and note original wire routing
• Position the clamp and secure with the existing fastener; do not overtighten
• Ensure wires aren't pinched and have clearance from the fan/compressor before restoring power

Specs: 8-18 AB IHW 5/8 S

This condenser fan mounting bracket secures the condenser fan motor and blade in the correct position to move air across the coils. Replacing a cracked or bent bracket restores stable mounting, reduces vibration, and helps maintain proper condenser airflow.

• Holds the condenser fan motor/blade assembly in alignment for proper airflow through the condenser
• Maintains clearance to prevent the fan blade from rubbing or contacting nearby components
• Helps reduce rattling, vibration, or scraping noises from the rear of the refrigerator
• Damage or misalignment can contribute to restricted condenser airflow and warmer temperatures

• Disconnect power and pull the refrigerator away from the wall to access the rear service area
• Remove the rear lower access panel; note wiring and hardware locations
• Support the fan motor/blade while removing the old bracket; transfer motor, blade, grommets, and screws to the new bracket
• The fan spins freely with proper clearance and correct airflow direction before reassembly