Gsh25wsxn Parts

This is the glass insert for the refrigerator pan cover, creating the flat shelf above the drawers. Replacing cracked or missing glass restores a stable, easy-to-clean surface and helps contain spills from reaching the storage areas below.

• Forms the flat shelf that tops the pan cover assembly over crisper/deli drawers
• Provides a sturdy surface for storing food items
• Helps contain small spills so they don't drip into drawers below
• Replace if the glass is cracked, shattered, chipped, bowed, or missing

• Disconnect power and remove food from the affected shelf area
• Lift out the pan cover frame and slide out the old glass
• Clean the frame's channels; seat the new glass fully and evenly
• Handle glass carefully and wear cut-resistant gloves

Size: 10-32 GXTT FLP.595 S

This freezer shelf restores lost storage and organization inside your freezer. Replace a broken or missing shelf to add a stable level for stacking and separating items so food stays accessible and easy to arrange.

• Provides an additional storage level inside the freezer
• Helps organize and separate frozen foods for quicker access
• Replaces a cracked, bowed, or missing shelf
• Seats into the freezer's existing side supports for a secure fit

• Remove food from the area before replacing the shelf
• Handle carefully; edges and corners can be sharp
• Align with the side supports and ensure the shelf is fully seated on both sides
• Distribute weight evenly; avoid overloading the shelf

This PTCR is the PTC start relay for the refrigerator's compressor. It briefly energizes the start winding to get the compressor running, then opens as it warms, supporting reliable starts and helping protect the compressor from repeated restarts.

• Provides initial current to the compressor start winding, then self-limits as temperature rises
• Supports consistent compressor startup to restore and maintain cooling
• Typical failure symptoms: compressor clicks or hums but won't start; refrigerator warm or not cooling
• Visible signs may include discoloration or heat damage at the relay or connector

• Disconnect power before servicing; allow sealed-system components to cool
• Note the relay's orientation; firmly seat it on the compressor terminals
• Inspect the overload protector and wiring; replace any heat-damaged components
• If the compressor still won't start, further diagnosis of the compressor, overload, and capacitor is recommended

This small guide sits at the icemaker fill area and manages the water stream. It directs incoming water into the fill cup and channels any excess safely away to help prevent splashing, leaks, and ice buildup inside the freezer.

• Guides the icemaker fill stream into the fill cup/funnel during the fill cycle
• Diverts stray or excess water to the overflow path to reduce spills
• Helps prevent leaks, sheets of ice, and clumped cubes under the icemaker
• Clues it may be needed: cracked, warped, or missing guide; water dripping from the fill area

• Disconnect power and turn off the water supply before servicing
• Remove ice bin and any covers to access the icemaker fill area
• Unclip/unscrew the old diverter; align and secure the new part to the fill cup/tube
• Restore water and power; run a test fill and check for leaks

This OEM part is a refrigerator dispenser interface. The dispenser interface is responsible for the main functions of the refrigerator, such as adjusting the temperature settings as well as the other functions that are displayed on the interface. If the refrigerator is no longer cooling efficiently, failing to maintain temperature, dispensing water, or the touchpad is unresponsive, the interface might need to be replaced. Thankfully, replacing this part is not a difficult process.To replace the old interface, make sure that all power to the refrigerator is turned off. Open the refrigerator door and remove the door panel of the interior of the refrigerator. Locate the old control board and remove the wire harnesses that connect to it. Take note of the wire connector's orientation and reinsert the wires to the new board. Snap the new interface back in place and reinstall the inner panel. This genuine replacement part is sold individually and is compatible with General Electric, Hotpoint, and RCA brand refrigerators.

This compressor overload protects the refrigerator's compressor by interrupting power when it overheats or draws excessive current. Replacing a weak or failed overload can stop repeated click/no-start symptoms and help restore normal cooling performance.

• Opens the circuit to protect the compressor during overheat or over-current conditions
• Automatically resets after cooling to prevent sustained damage
• Symptoms include: compressor won't start, rapid clicking from the compressor area, starts then stops, and a warm refrigerator/freezer
• Helps prevent motor and wiring damage caused by repeated overload events

• Disconnect power before servicing; wear appropriate PPE
• Access the rear machine compartment and remove the compressor/start device cover
• Note wire positions; pull the old overload straight off the compressor terminal and push the new one on fully seated; reconnect wiring and covers
• If the overload trips again after replacement, further diagnosis of the start relay, run capacitor, or compressor may be required

This evaporator fan bracket secures the evaporator fan assembly behind the rear panel. A rigid, correct-fit mount preserves blade clearance and airflow across the evaporator coils for steady temperatures while minimizing vibration and noise.

• Holds the evaporator fan assembly firmly in position
• Maintains alignment and clearance to prevent fan rubbing and excess noise
• Supports proper airflow through the evaporator compartment for consistent cooling
• Replace if the bracket is cracked, warped, or loose; symptoms may include rattling, scraping sounds, or the fan contacting the shroud

• Disconnect power before servicing and use cut-resistant gloves
• Remove shelves/drawers and the rear evaporator cover to access the fan assembly
• Transfer the fan motor and existing hardware to the new bracket; ensure the blade spins freely without contact
• Avoid damaging the evaporator coils; reassemble panels and restore power to test

This ice maker stripper is the front comb that helps release cubes from the ejector during harvest. It guides ice cleanly into the bin to reduce jams and keep ice production running smoothly. What it does

• Strips ice cubes off the ejector fingers as the ice maker cycles
• Directs cubes into the bucket, helping prevent jams and cube bridging
• Wear, cracks, or warping can cause cubes to stick, spill, or clump
• Symptoms include cubes piling at the front, clicking during harvest, or reduced/no ice

• 1 ice maker stripper

• Disconnect power and shut off water before servicing
• Remove the ice bin and access the ice maker front (remove cover if present)
• Release the old stripper (tabs/screws), align the new stripper with the ejector fingers, and seat it fully
• Reinstall cover and bin; restore power and allow a full cycle to verify operation

This ice maker fill cup directs water from the refrigerator fill tube into the ice maker mold so each cycle fills correctly. Replacing a damaged cup restores consistent ice production and helps prevent water spills. What it does:

• Channels water from the fill tube into the ice maker mold for proper tray filling.
• Prevents water from dripping into the freezer compartment when intact.
• A cracked, warped, or missing fill cup can cause underfilled ice cubes, overflowing molds, or water pooling in the freezer.
• Compatible with common top/front-mounted household ice makers that use a separate plastic fill cup.

• Disconnect power and shut off the water supply before starting work.
• Remove the ice bin or ice maker assembly as needed to access the fill cup.
• The cup typically snaps or slides into place; use gentle pressure and avoid forcing plastic tabs.

This clamp secures small hoses or tubing and nearby wiring inside the appliance to keep lines held in place and reduce rubbing, leaks, or vibration noise. It's a direct-fit replacement designed to restore proper hose routing and stability. What it does:

• Holds water, drain or vent tubing securely to prevent sagging and rubbing that can cause leaks or wear
• Keeps hoses and wires aligned to reduce vibration and rattling during operation
• Helps maintain proper connections at fittings so seals stay seated and drip risk is minimized
• Simple mechanical clip action — no special tools or adhesives required

• Disconnect power and shut off the water supply before starting any repair
• Remove the old clamp and install this clamp in the same orientation; tubing sits fully in the fitting
• Use standard pliers (or the OEM-recommended tool) to compress/seat the clamp; avoid twisting or pinching the tubing
• Inspect surrounding tubing and fittings for wear; replace damaged hoses or seals if found

This door handle fastener secures the refrigerator handle to the door so it stays tight and aligned. Replace a missing or stripped fastener to eliminate wobble and restore a solid, reliable grip.

• Attaches and locks the handle to the door or handle mounting point
• Maintains proper handle alignment and feel during daily use
• Common fix for a loose, wobbly, or falling-off handle
• Replace when the original fastener is missing, stripped, or damaged

• Protect the door finish with tape or a cloth around the work area
• Support and align the handle; start the fastener by hand to avoid cross-threading
• Tighten with the correct driver (hex/Allen or Torx, depending on model) until snug; do not overtighten

This damper gasket seals the refrigerator air damper opening between the freezer and fresh food compartments to prevent air leaks and help maintain stable temperatures. A new seal supports proper airflow and helps reduce moisture or frost near the damper. What it does:

• Seals the perimeter of the air damper/baffle to prevent bypass air leaks
• Helps regulate airflow from freezer to refrigerator for consistent cooling
• Wear, flattening, or tears can lead to warm spots in the fresh food section
• May also contribute to condensation, frost, or whistling/draft at the damper cover

• 1 damper gasket

• Unplug the refrigerator before servicing
• Remove the interior damper cover/grille to access the damper; note gasket orientation
• Seat the new gasket evenly around the damper frame without stretching or twisting
• Reinstall cover, restore power, and verify airflow and door sealing

This ice dispenser funnel guides cubes or crushed ice from the door chute into your glass. Replacing a cracked or missing funnel restores clean, targeted dispensing and helps reduce stray ice around the dispenser area.

• Directs ice from the chute into the cup to minimize spills and scatter
• Common symptoms: cracked or broken funnel, ice missing the glass, jamming at the outlet, loose/misaligned funnel
• Bisque finish to match bisque dispenser trim on compatible units
• Durable molded plastic designed for the dispenser recess

• Disconnect power to the refrigerator before servicing the dispenser area
• Carefully remove the dispenser trim/control panel; support any wiring harnesses
• Release tabs or screws holding the old funnel, note orientation, and transfer any existing hardware if needed
• Reassemble, restore power, and test both cubed and crushed ice for proper alignment

Includes 12 retainer rings.

This cable clamp secures refrigerator wiring to the cabinet, keeping harnesses organized and protected. Replacing a missing or damaged clamp helps prevent chafing and vibration noise while maintaining proper clearance from fans and other moving components.

• Anchors wire harnesses in their designed routing
• Helps prevent insulation wear from rubbing or vibration
• Keeps wires clear of sharp edges and moving parts
• Common signs it's needed: missing/broken clamp, loose or dangling wires, or new rattling/buzzing noises

• Disconnect power before servicing
• Access the clamp location and note original wire routing
• Position the clamp and secure with the existing fastener; do not overtighten
• Ensure wires aren't pinched and have clearance from the fan/compressor before restoring power