Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Upper hinge pivot pin for side-by-side refrigerator freezer doors. Replace if bent, worn, or missing to restore proper door alignment and swing.
By using my socket set Read more
Black plastic funnel extension attaches to the front of your refrigerator's ice dispenser. Replace if cracked, broken, or missing to reduce splashing.
Me and my husband fixed it. Thanks for the help. Read more
Base grille kickplate mounts across the lower front of your refrigerator, covering the condenser area. Replace if cracked, broken, or missing.
Used screwdriver to take it off and screw the part back on. the customer service was great. Read more
Black bottom door hinge and pin assembly for side-by-side refrigerators. Replace this load-bearing pivot component if cracked, broken, or worn out.
I replaced the lever asm. and spring Read more
Replacement mounting screw for refrigerator panels, brackets, door handles, and trim. Needed when original hardware is missing, stripped, or corroded.
Supplies electrical power from wall outlet to refrigerator. Replace this cord if cut, frayed, overheated, or damaged to restore safe electrical connection.
Spliced new and old power cord near the connections in the fridge and connected them. Didn't mess with the factory harnesses or connections inside actual fridge. Read more
Rubber grommet that mounts and cushions the compressor on your refrigerator or freezer. Replace if cracked, worn, or causing vibration noise from unit.
Installed new stainless steel pan replacing broken original plastic pan and installed new rubber grommets for the compressor Read more
Mounting screw fastens panels, brackets, and trim in refrigerators, dishwashers, and ranges. Replace missing, stripped, or rusty screws to secure parts.
Replaced the water tank. Followed the video instruction provided by Appliance Parts Pros. Very good instruction. Read more
Front mounting grommet for refrigerator ice makers. Secures ice maker assembly to freezer wall. Replace if cracked, missing, or worn to restore stability.
Replaced the housing the water filter screws into. Water works fine now. Read more
White plastic drip tray for refrigerator ice and water dispensers. Mounts on freezer door to catch drips. Replace if cracked, discolored, or missing.
Ordered the new interface display - this must be the easiest refrigerator repair possible. My version popped right off without even a screw (some models have a screw). There are 3 different sizes of connector to disconnect and hook up to the new board - so you really can't mess that up. Read more
Secures the evaporator fan shroud to the rear compartment frame. Replace if rusted, cracked, or broken to properly support the fan assembly and alignment.
The problem was most likely the evaporator fan motor but it could have been a bad blade, loose parts or bad motor mounts. Hard to tell without taking everything apart and inspecting. Since fridge was 17 years old I decided to order the entire evaporator fan assembly as shown in the parts diagram including fan blade, motor brackets, motor, motor mounts, screws, etc. Getting to the assembly involved removing the ice maker unit plus the entire rear inside of the freezer section. Parts cost around... Read more
White plastic housing shield for refrigerator ice/water dispenser assembly. Replaces cracked, broken, or damaged dispenser housing covers and frames.
Replaced dispenser kit and auger. Repair videos were a great help and resolved potential problems that I usually solved by trial and error. Thanks, Appliance Part Pros! Read more
Replaces a broken, cracked, or missing freezer shelf module in side-by-side refrigerators. Installs in factory side supports for organized storage.
Mounting screw for refrigerator doors, shelves, kickplates, and interior components. Replace missing, stripped, or corroded screws during repairs.
Great site to DIY! Purchased fresh produce drawer railing and parts. Fixed in under 10 minutes. Thanks so much! Read more
Bottom hinge that supports the refrigerator door weight and serves as the pivot point. Replace if worn, cracked, or causing door misalignment and sagging.
Replaced the hinges and all parts pertaining to hinges on the refrigerator door. Total cost was approx. $83 and it took 1 hour this morning (Saturday). Now the door is closing tightly. The refrigerator is 10 years old. GE brand. Read more
Replacement mounting screw for refrigerator panels, brackets, and hardware. Restores secure fit when original is missing, stripped, or corroded.
Hinge missing screws. Replaced 2. Perfect now Read more