Gtd695smjoes Parts

This strike plate mounts at the door opening and works with the door latch/strike to keep the appliance door securely closed during operation. Replacing a worn plate helps restore positive latching and reliable cycle start/stop via the door switch.

• Provides the catch surface for the door latch/strike to engage
• Helps keep the door closed and properly aligned
• Enables the door switch to engage so the cycle can run
• Common symptoms include: door won't stay closed, door pops open, unit won't start unless the door is pressed, visible wear or bending on the plate

• Disconnect power before servicing
• Open the door and remove the screws securing the existing plate
• Align the new plate with the latch/strike and fasten securely with the existing hardware
• Test door closure and latch engagement; adjust alignment if necessary

This factory screw secures dryer panels and internal components, keeping assemblies tight and aligned so the machine operates safely and without vibration or rattling.

• Fastens sheet-metal panels, brackets, or trim to the dryer cabinet/frame
• A loose or missing screw can cause panel vibration, noise, or misalignment
• Helps restore stability after service or when original hardware is lost
• Typical symptoms include rattling, loose panels, or gaps in trim

• Unplug the dryer before servicing
• Keep track of original screw locations and lengths; replace like-for-like
• Start screws by hand to avoid cross-threading, then snug—do not overtighten
• If threads are damaged, inspect mating hole or clip before installing

This dryer idler arm assembly keeps the drive belt tight and aligned so the drum turns smoothly. A worn or seized idler can cause squealing, belt slippage, or a drum that won't tumble.

• Applies tension to the drive belt and guides it around the motor pulley
• Maintains proper belt alignment for consistent drum rotation
• Common symptoms of failure: squealing/squeaking, belt coming off or wearing quickly, drum not turning, or burning rubber odor
• Pulley should spin freely; roughness or wobble indicates replacement is needed

• Disconnect power; if gas, also shut off gas supply before servicing
• Remove top/front panels as needed, release belt tension, and note belt routing
• Remove the old idler from its mount; transfer spring from the original if required by your model, then install the new assembly and re-route the belt
• Rotate drum by hand to verify belt tracking before reassembly and test run

This fuse holder secures a 3AB-style cartridge fuse within the appliance's electrical circuit. Replacing a cracked, loose, or heat-damaged holder restores a solid connection so the fuse can properly protect the circuit and prevent intermittent power issues.

• Provides a secure mount and reliable electrical contact for a 3AB cartridge fuse
• Helps ensure the protected circuit opens correctly during electrical faults
• Common symptoms of a failed holder: fuse won't seat, loose/burned contacts, intermittent or no power
• Direct replacement when the original holder is broken, heat-damaged, or cracked

• Disconnect power at the breaker or unplug the appliance before servicing
• Note wire positions and transfer one lead at a time to the new holder
• Install only a manufacturer-specified 3AB cartridge fuse of the correct rating
• Ensure the fuse seats firmly and all connections are tight before restoring power

The Trap Duct Assembly for Dryer is an OEM replacement part for GE dryers. It forms the internal ductwork connection between the dryer drum and the vent tube. This assembly is critical for proper airflow and efficient moisture removal during the drying cycle. 

Causes of a bad trap duct assembly can include cracks or loose connections due to heat fatigue over many cycles. Ducts must withstand temperature swings and mechanical stresses.

Symptoms of a bad trap duct assembly include:

• Increased drying times 
• Excess condensation or moisture remaining in clothes after cycles
• Visible cracks or damage to ducts

This GE replacement part is compatible with Hotpoint, RCA, and Kenmore dryer models. 

A replacement shield switch that helps the oven/microwave detect door position so the unit runs only when the door is closed. Restores reliable door sensing and user safety by replacing a worn or damaged switch. What it does

• Acts as the door-position sensing switch to allow operation only when the door is properly closed
• Stops intermittent or failed start issues caused by a worn or faulty door switch
• Helps correct symptoms like oven/microwave not starting, stopping mid-cycle, or inconsistent door detection
• Works as the plug-in electrical switch used in the door/shield assembly

• Disconnect power at the breaker or unplug the appliance before starting any repair
• Access may require removing the door or control/vent panels
• Handle small metal parts and electrical connectors carefully; avoid bending terminals
• Test door operation and proper function after installation

This valve and pipe assembly regulates and routes water for the dryer's steam feature. A new assembly restores proper water flow, helping resolve no-steam operation, weak spray, or leaks at the rear water connection.

• Opens and closes to supply water to the steam system when commanded
• Directs water from the household supply through the attached tube to the steam outlet
• Prevents water from entering the dryer when the steam feature is off
• Typical symptoms: steam option won't spray, weak or intermittent mist, dripping into the drum, leaks at the rear inlet, or valve buzzing with no water flow

• Disconnect power and shut off the water supply before servicing
• Pull the dryer forward to access the rear and place a towel to catch residual water
• Note hose orientation; transfer any fittings or clamps from the old part as needed
• Restore water and power, check for leaks, and run a brief steam cycle to verify operation

This burner assembly is the combustion head for GE gas dryers. It mixes gas and air and directs a stable flame into the heater housing, restoring consistent heat when the original burner is corroded, warped, or clogged.

• Directs the gas flame into the heat chamber for proper drying temperatures
• Works with the igniter, flame sensor, and gas valve to produce heat
• Typical failure symptoms: no heat or intermittent heat, long dry times, burner lights then goes out, unstable/yellow flame
• Physical issues can include rust, warping, or blocked burner ports

• Disconnect power and shut off the gas supply; allow the dryer to cool completely
• Note position of the igniter and flame sensor relative to the burner port; realign during reassembly
• Transfer any reusable fittings from the original burner as needed and verify orifice/fuel type match your installation
• After reconnecting gas, perform a leak check with a non-corrosive soapy water solution before restoring power

The Control Panel is an OEM part for GE electric clothes dryers. Located at the front of the dryer, it features digital displays, touch buttons, and a wiring harness connecting all electronic functions. 

As the central command module, the control panel facilitates cycle programming and monitoring through an intuitive interface. Its surface-mounted circuit board receives input signals from buttons to direct appropriate dryer operations via output currents. Easy-to-read displays convey cycle status updates.

Symptoms of a faulty control panel include:

• Buttons not responding properly to touch selections
• LED screens improperly lighting or remaining blank
• Dryer failed to advance through the expected sequence 
• Occasional disconnected internal electrical links

Replacing with the OEM GE part restores the core command center and touch-interactive interface. Proper dryer functionality and programmability are ensured through dependable controls. Compatible with some Kenmore models.

This leveling leg threads into the base of your appliance to provide a stable, adjustable footing. Replacing a worn or missing leg helps keep the cabinet level, reducing vibration and noise for smoother, safer operation.

• Adjusts height so the unit can be leveled on uneven floors
• Maintains solid floor contact to minimize rocking or walking
• Helps reduce vibration and rattling noises during operation
• Signs you need this part: appliance wobbles, sits unevenly, or a foot is missing/damaged

• Disconnect power; for gas units, also shut off the gas supply
• With assistance, carefully tilt or raise the appliance to access the leg
• Unscrew the old leg and thread in the new leg by hand; use a wrench if needed
• Level the unit front-to-back and side-to-side; ensure all legs firmly contact the floor

This replacement screw secures panels, trims, and internal components to restore a snug, rattle-free fit and reliable operation. Use it to replace missing, corroded, or stripped fasteners for safe appliance performance. What it does:

• Fastens cabinet panels, trim pieces, and internal brackets to keep parts aligned and secure
• Replaces missing or damaged screws that cause loose or vibrating panels
• Prevents movement that can lead to wear, noise, or improper sealing
• Matches the original fastener role for appliances that specify part WE2M160

• Disconnect power or unplug the appliance before attempting any repair
• Use the correct screwdriver or driver bit to avoid stripping the head
• Install until snug; avoid overtightening which can strip threads or crack plastic
• If threads are damaged or fastener holes are worn, replace damaged components.

This hex washer-head screw secures dishwasher components like brackets, shields, and panels. Replacing a stripped or missing screw restores a tight fit and helps prevent vibration, rattling, and loose parts during operation.

• Fastens parts where a #10-16 x 1/2-inch hex washer-head screw is specified
• Secures brackets, panels, and assemblies to the tub or frame
• Helps resolve symptoms like loose panels, vibration, or rattling noises
• Restores proper hold when the original screw is stripped, missing, or damaged

• Disconnect power and shut off water to the dishwasher before servicing
• Match length and thread to the original; replace screws one at a time to maintain alignment
• Start threading by hand to avoid cross-threading; tighten snugly—do not overtighten, especially into plastic
• Verify no wires or hoses are pinched before reassembly

• Size: #10-16 x 1/2 inch
• Head: hex washer-head
• Type: AB tapping screw

A replacement strain relief bracket that secures the appliance power cord at the entry point, protecting wiring and the terminal connection from pull and wear. Restores proper cord routing for safer, more reliable electrical connection. What it does:

• Secures the power cord where it enters the appliance to prevent tension on terminals and wiring.
• Helps reduce intermittent power, loose connections, or arcing caused by a tugged or poorly routed cord.
• Maintains correct cord routing and support to match the original mounting location and fit.
• Useful when the original bracket is cracked, broken, or no longer holds the cord firmly in place.

• Disconnect power at the breaker or unplug the appliance before starting any repair.
• Access is typically from the rear; remove the back access panel to reach the cord entry and terminal block.
• Remove mounting screws holding the old bracket, position the cord, and secure the new bracket without over-tightening; reuse original hardware if appropriate.
• Inspect the power cord and terminals for damage—replace damaged wiring.

Includes 12 screws. Size: 8-18 ab.

This replacement motor strap secures the dryer's drive motor to its mounting bracket so the motor and blower stay aligned and stable, helping reduce vibration and noise for smoother operation. What it does:

• Holds the drive motor firmly to the base/bracket
• Maintains proper alignment of the motor and blower wheel to prevent rubbing
• Helps reduce vibration, rattling, and related noise
• Typical signs of failure: increased vibration, rattling, scraping from the blower area, or a motor that feels loose inside the cabinet

• Includes 1 motor strap

• Disconnect power; for gas dryers, also shut off gas supply
• Access the motor assembly; note the strap's routing/orientation before removal
• Support the motor while releasing the strap to avoid stressing wiring and mounts
• After securing the strap, rotate the drum/blower by hand to verify free movement before reassembly

This plug button is a replacement cosmetic/functional cap that covers an unused control opening or receptacle on the appliance, restoring a finished appearance and helping keep out dust and debris. What it does:

• Covers and seals an unused control hole or plug location to improve appearance
• Helps prevent dust, lint, and small debris from entering the opening
• Restores a flush, finished look when a switch, knob, or connector is missing
• Simple snap-in design for a clean, low-profile result

• Disconnect power to the appliance before servicing.
• Typically snaps into place; no special tools required for most installations.
• If removal is needed, use a plastic pry tool to avoid scratching surrounding surfaces.
• Your appliance owner's manual or parts diagram to correct placement.