Gtw725bsnows Parts

This control board kit replaces the washer's user interface and main control electronics. It helps restore proper power-up, input response, and accurate cycle execution when the original boards fail.

• Interprets button/knob inputs and drives console indicators
• Manages cycle logic and timing for wash, drain, and spin
• Controls valves, motor, pump, and door/lid lock per selections
• Typical symptoms: dead or blank console, won't start, unresponsive buttons, cycles that won't advance, control-related error codes

• Disconnect power before servicing; boards are sensitive to static—use ESD protection
• Note wire locations and connector orientation before removal
• Secure boards and fully seat connectors to avoid intermittent issues
• Complete any programming/option selection steps and run a test cycle

The Internal Drain Hose Asm is an OEM part for GE washers. It is the hose located inside the washer that channels drained water from the tub out to the external drain system. 

Proper drainage is essential for washer operation. Causes of a bad internal hose can include cracks, kinks, or holes developing over time, especially in hoses made of brittle plastic material. Mineral buildup can also obstruct flow.  

Symptoms of a bad Internal Drain Hose Asm include:

• Puddling or pooling of water inside the washer tub after cycles
• Water not fully draining or draining slowly from the tub  
• Leaks or wet surroundings near the back of the washer

This GE replacement hose ensures your washer continues draining efficiently. This is also compatible with Hotpoint, RCA, and some Kenmore models.

The anti-siphon clip secures the washer's drain hose to a standpipe or laundry tub, maintaining the proper air gap to prevent siphoning and backflow. It keeps the hose stable so the washer fills and drains as intended.

• Maintains an air break at the drain to help stop unintended siphoning
• Holds the drain hose securely to a standpipe or sink/tub
• Helps prevent "filling and draining at the same time" or low water levels
• Helps keep the hose from vibrating loose or popping out during cycles

• Unplug the appliance and shut off water before starting
• Route the drain hose per the installation manual; avoid kinks or submerging the hose end
• Snap the clip onto the hose and fasten it to the standpipe or tub edge
• Run a quick test to verify no leaks and correct hose position

The Mode Shifter is an OEM component specifically designed for GE washing machines. It contains the internal gears and linkage mechanisms that shift the transmission between spin, agitate, and drain functions depending on the selected wash cycle settings. 

Symptoms of a bad mode shifter include:

• Abnormally loud grinding noises coming from inside the washer
• Inability to advance fully through cycles or change functions  
• Excessive vibration felt in the washer or surrounding cabinetry
• Poor cleaning performance from ineffective agitation 

Causes of mode shifter malfunction involve worn gears, damaged or loosened internal components, or blockages preventing smooth operation over extended use.

This OEM GE replacement part is also compatible with some Hotpoint, RCA, and Kenmore models. Reliable transmission shifting promotes optimized washing performance. 

This suspension ball joint grease kit is used on washers to lubricate the suspension's ball-and-socket pivots. Proper lubrication helps the tub move freely, reducing squeaks and binding so the suspension can control vibration and balance the load.

• Provides manufacturer-specified lubricant for the suspension ball-joint/pivot sockets
• Helps quiet squeaking or creaking as the tub moves during wash and spin
• Promotes smooth, free tub articulation to reduce binding and friction

• Disconnect power and turn off water before servicing; use proper lifting/support to access the suspension
• Clean old grease and debris from the ball-and-socket contact areas
• Apply a thin, even coat of the supplied grease to the contact surfaces only; avoid excess
• Reassemble and verify the tub moves smoothly by hand before running a test cycle

The Lid Lever Arm is an OEM part for GE washing machines. This component is crucial for the proper functioning of the washer's lid mechanism, ensuring that the lid locks securely during operation and allows for safe and efficient washing cycles.

Over time, the lid lever arm can become worn out or damaged due to regular use, improper handling, or mechanical failure. Causes of a bad lid lever arm include physical damage, wear and tear from repeated use, or issues with the linkage that connects it to the locking mechanism.

Symptoms of a bad lid lever arm include:

• The washer lid not locking properly
• The washing machine not starting or pausing unexpectedly
• Error codes related to lid lock issues
• The lid feeling loose or misaligned

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Platform Transmission Assembly Kit is an OEM part for GE washers. As the central mechanical linkage, this assembly connects the transmission gears to the rotor motor shaft. 

The platform trans kit includes the transmission gears, belt, mounting hardware, and flexible coupler which transfers rotary motion from the motor to the wash basket drum. During agitation, it coordinates oscillating movement. For spin, it facilitates high-rpm extraction via a series of spinning planetary gear reductions.

Symptoms of a bad platform trans kit include:

• Erratic or no agitation movement  
• Failure to achieve proper spin speeds
• Grinding noises and vibrations during the operation
• Belt slipping off tracks or shredding

This genuine GE OEM part also fits Hotpoint, RCA, and select Kenmore units for years of reliable performance.

This lid lock harness clip secures the lid lock wire harness to the washer cabinet or top. It keeps the wiring routed and protected to help prevent chafing, snagging, and intermittent lid-lock performance issues. What it does / common symptoms:

• Holds the lid lock wire harness in place along the cabinet/top
• Maintains proper routing to avoid pinching or rubbing on moving parts
• Reduces vibration-related wear on the wiring
• Symptoms of a failed/missing clip: loose or dangling harness, scuffed insulation, intermittent lid-lock response

• 1 lid lock wire harness clip

• Disconnect power before servicing
• Access the lid lock wiring path (lift top/remove console as required by your model)
• Release the old clip from the panel and harness; snap the new clip into the mounting hole and secure the harness
• Ensure the harness has adequate slack and is not pinched before restoring power

This screw is a factory fastener used to secure appliance components. Replace a missing, stripped, or corroded screw to keep panels, brackets, and assemblies tight and help prevent vibration or rattling from loose hardware.

• Secures panels, brackets, and internal assemblies at their mounting points
• Replaces lost, rusted, or stripped hardware for a solid, reliable hold
• Helps reduce vibration, rattling, or shifting caused by loose fasteners
• 1/4-20 thread per OEM designation for proper fit where specified

• Disconnect power and, if applicable, shut off water supply before servicing
• Start threads by hand to avoid cross-threading, especially in plastic
• Tighten snugly; do not overtighten to prevent stripping or cracking
• Verify alignment and stability of the secured component after installation

This replacement siphon cap fits the washer's dispenser assembly. The insert creates the siphon action that empties the additive cup during the rinse cycle, helping prevent standing liquid and residue so liquid additives dispense as intended.

• Forms a siphon in the dispenser cup so liquids empty at the proper time
• Helps reduce standing water and residue buildup in the dispenser
• A worn or missing cap can contribute to odors or buildup in the dispenser area

• Unplug the washer and turn off water before servicing
• Remove the dispenser drawer or cup and lift out the old siphon cap
• Clean the dispenser area; press the new cap in firmly so it seats evenly
• Reinstall the drawer/cup and run a rinse to ensure proper dispensing

The Top Cover is an OEM part for GE washing machines. It serves as the top panel enclosure for the washer, covering internal components and shielding them from potential water damage or intrusion of foreign objects. The top cover also plays a cosmetic role, providing a sleek design finish to the top of the appliance.

Symptoms of a bad top cover include:  

• Cracks, breaks, or looseness developing in the plastic material over time
• Missing or damaged mounting screws  
• Water leaks or moisture inside the panel enclosure area
• Dents, dings, or other exterior damage affecting appearance

Causes of a bad top cover are generally related to wear and tear from repeated usage and loading/unloading of clothes over the years. General handling can also lead to minor impacts or stresses that result in cracks or breaks.

This genuine GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This factory-spec screw secures internal brackets, housings, and panels. Replacing a missing, stripped, or corroded fastener with the correct #6-32 size restores a tight, corrosion-resistant fit that keeps assemblies aligned and helps reduce vibration noise.

• Provides #6-32 machine-thread fastening for appliance components
• Helps maintain alignment and stability of brackets, housings, and panels
• Replaces stripped, rusted, or missing hardware that can cause looseness or rattling
• Stainless construction resists corrosion in high-moisture areas

• Disconnect power and, if applicable, shut off the water supply before servicing
• Start threads by hand to avoid cross-threading; use the correct driver for the head type
• Tighten snugly without overtightening, especially into plastic or thin sheet metal

The Dispenser Drawer is an OEM component specifically designed for GE top-load washing machines. It provides centralized access for adding detergents or other treatment products.

Located near the top of the washer interior, this plastic drawer features built-in compartments tailored for optimal dispensing of laundry pods or liquids. Its smooth sliding motion via metal rails facilitates easy loading before each cycle begins. 

Causes of failure can involve cracking or breaking from overloading, binding tracks from debris/ residue buildup over time, or holes developing that cause premature dispensing.

Symptoms include:

• Inconsistent cleaning or rinsing results   
• Premature dispensing of chemicals or residues
• Drawer difficult to open or close fully

Replacing with this authentic GE OEM part restores convenient one-place access for laundry essentials. Compatible units include select Hotpoint, RCA, or Kenmore top-load models.

This harness wire tie secures and organizes the appliance's wiring harness. Replacing a damaged or missing tie keeps wires properly routed and protected to help prevent chafing, disconnections, and vibration noise for more reliable operation. What it does:

• Bundles and anchors wiring harnesses along the intended routing path
• Helps prevent wire insulation from rubbing, pinching, or wearing through
• Reduces rattling or vibration noise from loose wires
• Common signs include a broken/missing tie, dangling wires, or visible wear on the harness

• 1 harness wire tie

• Disconnect power before servicing; allow any moving parts to stop
• Note original wire routing and mounting location; take a photo for reference
• Install the new tie at the same point and snug it just enough to secure without crushing wires; trim excess strap
• Verify wires are clear of moving or hot components before restoring power

A small mounting support that provides a stable anchor point for screws used to secure panels or internal assemblies. Replacing a damaged screw platform restores proper fastener engagement and reduces panel movement and vibration. What it does:

• Anchors screws to hold trim, panels or internal components in place
• Restores secure attachment when the original mounting point is cracked or worn
• Helps eliminate rattling, loose panels, or alignment issues caused by a failed mounting surface
• Works with the appliance's existing screws and surrounding hardware to maintain structural fit

• Disconnect power to the appliance before attempting any repair
• Use the correct screws and a properly sized screwdriver to avoid further damage
• Inspect surrounding mounting points and replace any stripped screws or damaged clips as needed

The Lid Hinge is an OEM part for GE washers. It provides the mounting and fulcrum point for the washer lid, allowing smooth movement between open and closed positions. The sturdy hinge construction is designed to withstand repetitive use over many cycles.

Causes of a bad lid hinge can include fatigue from extended use, damage or loosening of mounting screws, or impact dents deforming the metal.

Symptoms include:

• Looseness, wobbling, or sagging of the washer lid 
• Difficulty fully opening or closing the lid securely
• Noise or squeaking emitted from the hinge area
• Physical deformation reducing the proper range of motion

This OEM GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models. Replacing a worn or faulty lid hinge ensures comfortable, predictable lid movement for years to come.