Gtw750 Parts

This 10-32 machine screw fastens small appliance components and replacement assemblies, restoring secure mounting and reliable electrical or panel connections. Its length fits common cabinet, control, and bracket attachments. What it does

• Secures control boards, panels, brackets, and grounding tabs using a 10-32 machine thread
• Replaces stripped or missing mounting screws that allow panels or parts to rattle or shift
• Helps restore stable electrical connections where a threaded fastener is required
• Works where a 1.31 in (approx. 1-5/16 in) long 10-32 screw is specified

• Power off and unplug the appliance before beginning any repair
• Match thread size and length to the original screw; do not force a wrong-size fastener
• Start threads by hand to avoid cross-threading; tighten securely but do not overtighten
• Use appropriate tools and wear eye protection when working on metal assemblies

This lid front corner bumper cushions the washer lid and helps reduce noise, wear and abrupt contact when the lid closes. It restores smooth, quiet operation at the lid's front corner. What it does:

• Acts as a soft contact point between the lid and cabinet to dampen impact and vibration
• Prevents metal-on-metal contact that can cause chipping, scratching or rattling
• Helps keep the lid aligned for consistent closing and latching
• Commonly replaced when the lid squeaks, chips, or does not sit flush

• Lid front corner bumper

• Disconnect power to the appliance before beginning any work
• Typically installs by hand or with light pressure into the lid or cabinet corner; use gentle force to avoid damage
• Inspect surrounding area for cracks or wear and replace other damaged bumpers if needed

This silicon controlled rectifier (SCR) switches and regulates power in compatible appliance control circuits, helping the unit deliver correct power to heating elements or motors. It's a direct replacement component when the original SCR fails. What it does

• Acts as a solid-state switch that controls current flow to heating elements, motors or other high-current circuits.
• Fails open or shorted when worn; common symptom is loss of heating, intermittent power to the controlled component, or no operation on affected circuits.
• Provides fast, repeatable switching compared with electromechanical relays.
• Designed for stud-mount installation with insulated/marked terminals for correct wiring.

• One silicon controlled rectifier (SCR) as listed.

• Disconnect all power before accessing or replacing the SCR to avoid shock or equipment damage.
• Note terminal orientation and wiring before removal; replace with the same terminal/stud configuration.
• Avoid electrostatic discharge to the replacement part; handle by the body and avoid touching terminals.

This GE Ball Joint Upper is an OEM part for GE washing machines. Designed to ensure smooth and stable movement of the washing drum, this ball joint plays a crucial role in the appliance's suspension system. 

A compromised ball joint can lead to a decline in the performance of the washing machine, making it essential to address the issue promptly.

Symptoms of a bad Ball Joint Upper include:

• Unusual noises during operation, especially during the spin cycle.
• The drum may seem to wobble or be off-balance.
• Excessive vibration of the machine, more than usual.
• Uneven wear of other suspension parts, leading to further maintenance issues.
• Potential leakage or damage to surrounding components due to misalignment.

This GE OEM replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
 

The Start Capacitor is an OEM part for GE washing machines. It is comprised of a bracket and capacitor, which work together in the motor control circuit to start and run the drive motor. The capacitor provides a phase shift that allows for smoother operation of the electric motor.

Symptoms of a bad Start Capacitor include:

• The washer fails to agitate or spin clothes
• An electric burning smell coming from the motor or control board  
• The drive motor makes buzzing or humming noises during the operation

Causes of failure can be normal component degradation over time. Exposure to moisture, physical damage, or operating the machine with an unbalanced load can also stress the capacitor prematurely. 

This OEM GE part is also compatible with Hotpoint, RCA, and select Kenmore models.

The External Drain Hose is an OEM part for GE washers. It is responsible for directing excess water from the washer out of the home during the drain cycle. The external drain hose connects from the bottom of the washer to an external drain point, such as a standpipe, drain pump, or utility sink. 

Causes of a bad external drain hose can include cracks, leaks, or holes developing over prolonged use. Mineral buildup or contaminants inside the hose can also cause blockages.

Symptoms of a bad external drain hose include: 

• Water failing to drain or draining slowly during the cycle 
• Puddles or flooding occurring near or beneath the washer
• Strange draining noises or sounds emanating from the hose

This OEM GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Power Cord is an OEM part for GE washers. It provides the crucial connection, transmitting electrical current from the wall outlet to power the washer components and functions. Ensuring the integrity of this cord is vital for safe and reliable operation. 

Symptoms of a bad power cord include:

• Frayed, cracked, or exposed copper wiring 
• Loose connections at either end
• Buzzing, sparks, or shocks felt around the cord
• The washer fails to power on as expected

Causes can be normal flexing wear over thousands of cycles, damage from pinching, rodents, or excess tension on the cord. 

This OEM GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
 

Center lid bumper cushions and aligns the washer lid to reduce noise and prevent metal-to-metal contact. Replace a worn or missing bumper to restore quieter, smoother lid closing and protect the lid edge and cabinet finish. What it does:

• Cushions the lid to reduce slamming, rattling and impact noise
• Helps the lid sit evenly to prevent rubbing or uneven closing
• Protects the lid edge and cabinet finish from contact damage
• Common symptoms: noisy or uneven lid closing, visible wear or missing bumper

• Unplug the appliance or disconnect power before servicing.
• Typically snaps or presses into a mounting boss under the lid; remove the old bumper before installing the new one.
• Use a non-marring tool or gloved hand to avoid scratching the lid; inspect surrounding mounting area for damage.

This is a self-tapping Plastite screw with a hex washer head and a 5/8 in. length that secures plastic and thin-sheet components. Use it to replace missing or damaged mounting screws for a snug, reliable fit. What it does:

• Forms threads in plastic (Plastite style) to fasten panels, brackets, and trims.
• Hex washer head provides a larger bearing surface for better holding power.
• Replaces stripped, corroded, or missing screws to stop loose or rattling parts.
• Works where a self-tapping screw is required for secure mounting without a separate nut.

• Use the correct hex/nut driver and a properly fitting bit to avoid stripping the head.
• Hand-start the screw and drive straight to prevent cross-threading; stop when snug—do not overtighten into plastic.
• Unplug the appliance or shut off power before disassembling or working near electrical components.
• Replace with the same screw type and size to maintain proper fit and function.

This molded wire tie standoff provides a secure anchor point for a cable tie to hold wiring and harnesses away from moving parts and hot or sharp surfaces, helping reduce wear and electrical risk. Fits common HVAC and appliance wiring panels. What it does:

• Anchors wire ties to the appliance cabinet or chassis so harnesses stay routed and secured
• Prevents wires from rubbing on sharp edges, hot components or moving parts
• Helps stop intermittent electrical issues from loose or vibrating connections
• Reduces noise from loose wiring that can vibrate during operation

• One wire tie standoff

• Disconnect power before servicing the appliance to avoid shock or damage
• Mount in the original standoff hole or approved panel location; secure a cable tie through the top loop to hold the harness
• Use the correct fastener or snap method for your model—do not force or overtighten
• If routing or attaching multiple wires, verify clearance from heating elements and moving parts

This belt protector is a replacement cover that shields the dryer drive belt and nearby components from damage, helping maintain smooth drum rotation and prevent premature belt wear. What it does:

• Covers and protects the dryer drive belt from contact with the cabinet and foreign objects
• Helps prevent belt fraying and rubbing that can cause noise or reduced performance
• Keeps lint and debris away from the belt path to reduce overheating risk
• Supports proper belt routing for consistent drum movement

• Disconnect power to the appliance before starting any repair
• Access typically requires removing the dryer top or rear panel—use basic hand tools
• Inspect the drive belt and idler for wear while the protector is off; replace if damaged

This water valve harness is a direct-replacement wire harness that connects the refrigerator's water valve to the control and power source, restoring proper electrical connection for water dispensing and ice maker fill functions. What it does:

• Provides the electrical connections between the fridge control and the water inlet/solenoid valve
• Restores power/signal delivery to the water valve so the dispenser and icemaker can fill
• Commonly used when the valve won't actuate or water flow is intermittent
• Helps replace damaged, corroded, or broken wiring/connectors that prevent reliable operation

• Disconnect power and turn off the water supply before beginning work
• Match connector shapes and pin counts; do not force connectors or bend pins
• Inspect mating connectors and valve terminals for corrosion; replace if needed
• Secure harness away from sharp edges and moving parts; test dispenser/icemaker after reassembly

This basket assembly is the removable silverware/utensil basket used to hold flatware and small dishwasher-safe items during wash cycles, helping keep pieces contained and separated for better cleaning and drying. What it does:

• Holds forks, knives, spoons and small dishwasher-safe tools securely during wash cycles
• Keeps small items contained to prevent them from falling to the bottom of the tub
• Helps separate utensils for improved water flow and more even cleaning
• Fits into the dishwasher lower rack and is removable for loading and unloading

• One silverware/utensil basket assembly

• No tools required for normal removal and replacement; basket simply snaps or slides into the lower rack
• Remove sharp utensils by hand and handle with care to avoid cuts during installation
• Inspect rack guides for damage before seating basket to ensure proper fit
• Refer to your dishwasher user manual for rack removal instructions if access is restricted

A replacement funnel bezel for the dispenser that restores the dispenser opening and helps guide water or ice into your cup with a finished look. Fits the dispenser area to repair cosmetic damage or broken trim. What it does:

• Replaces cracked, broken or missing dispenser trim that can catch drips and obstruct dispensing
• Guides water and ice into the cup to reduce splashing and misalignment
• Restores the original appearance of the dispenser opening
• Works with the dispenser assembly to help maintain proper user access

• Disconnect power to the appliance before servicing to reduce shock risk
• Usually installs from the front of the dispenser; remove adjacent trim or liners if needed for access
• Handle gently to avoid scratching the finish and align snaps or tabs before pressing into place

This hex-head machine screw secures appliance panels and internal components where a 5/16-24 x 1 inch fastener is required. Durable replacement for stripped or missing screws to restore safe assembly and reduce vibration. What it does:

• Fastens panels, brackets, and assemblies with a 5/16-24 machine thread.
• Replaces worn, stripped, or missing screws that can cause rattling or loose parts.
• Provides a secure, threaded connection for metal-to-metal or tapped-hole repairs.
• Matches OEM thread and length to maintain proper fit and alignment.

• Disconnect power and unplug the appliance before servicing.
• Use the correct hex driver or socket to avoid rounding the head.
• Thread into matching 5/16-24 tapped holes; do not force into incorrect thread sizes.
• Tighten snugly but avoid over-torquing to prevent stripping the tapped hole.

This tub cover replaces the top washing-tub cover that protects internal components and helps contain water and agitation inside the wash basket. It restores the washer's sealed tub appearance and helps prevent direct contact with the internal tub. What it does

• Covers the top of the washer tub to help keep water and laundry inside the wash basket
• Shields internal components from splashes and debris during a wash cycle
• Helps maintain correct spacing and alignment for the tub assembly
• Commonly replaced when cracked, warped, or visibly damaged

• One tub cover

• Disconnect power and water supply before starting any repair
• Remove control panel/agitator and/or trim as required to access the tub cover
• Replace the cover without forcing parts; check for proper fit and alignment before reassembling