Gu2300xtvo2 Parts

Bushing, Door spring

Color: Black

This hanger anchors the dishwasher's door-balance spring to the frame so the door opens and closes smoothly. Replacing a worn or broken hanger restores proper spring tension and helps prevent a door that drops, slams, or feels heavy.

• Secures the door balance spring to the dishwasher cabinet/frame
• Maintains correct spring tension for smooth, controlled door movement
• Helps fix a door that falls open quickly or won't stay in position
• Useful to replace when door balance hardware shows wear or damage

• Disconnect power and shut off water before servicing; remove the toe panel/kickplate
• Support the door and carefully relieve spring tension before removing parts
• Slide the dishwasher out if needed for side access; transfer the spring to the new hanger and reinstall
• Inspect the opposite-side spring/link and hinge for wear; verify door balance before reassembly

Color: light gray. Measures about 3 inches high by 6 inches deep.

This adjustable manifold connects the upper rack to the dishwasher's rear water feed. It channels wash water to the upper spray arm and maintains a sealed connection as the rack height changes for consistent cleaning performance. What it does:

• Routes water from the rear feed tube to the upper/middle spray arm
• Self-adjusts with rack position to keep a secure, leak-resistant connection
• Replace if cracked, deformed, or the coupling no longer seals
• Common symptoms include poor cleaning on the upper rack, weak spray, upper spray arm not turning, or a small leak at the back of the tub

• 1 adjustable manifold

• Disconnect power and shut off water; wear gloves for protection
• Remove the upper rack by releasing the rail end caps and sliding the rack out
• Unclip the manifold from the rack and disengage it from the rear feed port; seat the new manifold fully
• Reinstall the rack and ensure the spray arm spins freely

Size: 1/4 inch hex head, 10-12 x 1/2 inch.

Includes vinyl rack repair touch up paint and tine tip covers. Color: Grey

This hose clamp secures dishwasher hoses to fittings and ports to maintain a tight, leak-resistant seal. Replacing a worn clamp helps prevent drips and loose connections that can cause water under the unit.

• Secures drain or circulation hose to the pump, sump, or other dishwasher fittings
• Helps maintain a watertight seal at hose connection points
• Can help resolve water dripping from a hose joint or a loose hose
• Replace if corroded, deformed, cracked, or no longer holds tension

• Disconnect power and turn off the water supply before servicing
• Place a towel or shallow pan to catch residual water when removing hoses
• Fully seat the hose on the fitting, position the clamp over the barb/connection, and secure firmly
• After reassembly, run a brief fill/drain and check all connections for leaks

12 Ft in length

Includes two screws, two clamps, and undercounter mounting brackets.

Color: White

Located between the console and door

Bottle with brush. Color: Biscuit paint. It's point-six fluid ounces.

This foam pad installs between the inner and outer door panels of a dishwasher to dampen sound and help shield the outer panel from heat and moisture, keeping operation quieter and the door better protected. What it does:

• Lines the inside of the outer door panel to reduce operating noise and vibration
• Acts as a thermal and moisture barrier for the outer door panel
• Helps maintain proper door performance when the original insulation is worn or missing
• Replace if torn, degraded, or waterlogged, or if noise/condensation around the door has increased

• 1 door insulation pad

• Disconnect power and shut off water to the dishwasher before servicing
• Support the door; remove perimeter screws to separate the inner and outer door panels
• Note the pad's orientation; seat the new insulation evenly without pinching wires or harnesses
• Reassemble panels and fasteners; verify smooth door/latch operation

To order seal use WP8268340.

This replacement screw secures appliance panels and components so they stay tight and aligned. Replace a missing, rusty, or stripped fastener to restore a solid hold and reduce vibration or rattling during operation. What it does:

• Fastens and secures panels, brackets, trim, or internal components as specified for your model
• Replaces missing, corroded, or stripped hardware to restore a proper fit
• Helps prevent vibration, rattling, and misalignment caused by loose fasteners
• Addresses issues like a loose panel/handle or a screw head that's rounded off

• 1 screw

• Disconnect power; if applicable, shut off gas and water before servicing
• Use the correct driver size; start by hand to avoid cross-threading
• Tighten snugly—do not overtighten into plastic or thin sheet metal
• Keep track of original screw locations and lengths during reassembly