Gud24essjdww Parts

This dryer gasket seals critical air paths in your GE dryer to maintain proper airflow, temperature, and efficiency. Replacing a worn seal helps prevent heat loss and lint escape while reducing noise and friction.

• Creates an air-tight seal in the dryer to keep heat and airflow where they belong
• Helps contain lint and moisture within the drum and exhaust path
• Supports efficient drying performance and consistent temperatures
• Common failure signs: longer dry times, warm air leaking near the opening, visible tears or fraying, excess lint around the door/front panel

• Disconnect power; turn off gas supply before servicing
• Allow the dryer to cool completely; wear cut-resistant gloves
• Access the gasket location per your model's service instructions
• Remove the old gasket and residue, clean the surface, position the new gasket correctly, and reassemble; allow any adhesive to set if your model requires it

This replacement hinge supports and pivots the appliance door so it opens and closes smoothly and stays aligned. A worn or bent hinge can lead to door sagging, scraping, or poor latching that impacts performance and safety. What it does

• Supports the door and provides the pivot point for opening/closing
• Maintains door alignment to help ensure a proper seal
• Restores smooth, consistent door motion
• Common symptoms: door sags, squeaks, scrapes, or won't latch/stay closed

• 1 hinge

• Disconnect power before servicing; for gas units, also shut off gas supply
• Support the door while removing/installing fasteners to prevent stress on the panel
• Reuse original mounting screws/hardware unless damaged
• After installation, adjust if needed

This washer motor run capacitor stores and releases electrical energy to help the drive motor start and run smoothly. Replacing a weak capacitor can help restore consistent agitation and spin and reduce motor humming or stalling under load.

• Provides the phase shift and torque assist the drive motor needs to start and stay running
• Can address: washer won't start, no agitate or spin, motor only hums/buzzes, or stops under load
• Visible clues of failure can include a swollen, cracked, or leaking capacitor case

• Unplug the appliance before servicing; capacitors can retain a charge even when power is off
• Discharge the capacitor safely before handling
• Note wire positions; move leads to the same terminals and secure the capacitor in the original bracket/orientation
• Inspect connectors and replace any burnt or loose terminals to ensure a tight fit

The Rotatory Knob is an OEM part for GE washers. It allows users to easily select and change washer settings like cycles, temperatures, and options with a simple turn. As a control interface component, the rotatory knob provides direct input to the washer's control board.

Causes of a bad rotatory knob can be normal wear from frequent use over time. Exposure to moisture, physical impacts or mishandling, and mineral buildup are other potential causes of malfunction. 

Symptoms of a bad rotatory knob include:

• Difficulty selecting or changing washer settings  
• Loose, wobbly, or unresponsive knob behavior
• Inaccurate input to the control board causes operating issues
• Cracks, splits, or broken knob components

Compatible with some Hotpoint, RCA, and Kenmore models as well.

Replacement control board assembly that manages the appliance's electronic controls, coordinating cycle timing, sensors and outputs to restore reliable operation of functions like cycles, displays and automated controls. What it does:

• Receives input from the user interface and sensor signals, then sends control signals to motors, valves, heaters or igniters.
• Manages cycle timing, sequencing and feature activation for electronic appliance functions.
• Common symptom indicator: blank, unresponsive or erratic control panel and intermittent or no operation of electronic cycles.
• Can cause failure to start or cycles that stop, restart or behave unpredictably when defective.

• Disconnect all power (unplug or switch off breaker) before accessing the control area.
• Handle the board by its edges; avoid contact with components and use anti-static precautions.
• Basic panel removal and wire-transfer are typically required.

This tub suspension support assembly stabilizes the wash basket during agitation and spin to control vibration and noise. Replacing a worn support helps restore smooth, balanced operation and reduce off-balance interruptions.

• Supports and centers the tub/wash basket within the cabinet
• Damps movement to reduce vibration during wash and spin
• Helps prevent banging, thumping, and the washer "walking"
• Replace if the tub sags or sits low on one side
• Can help resolve frequent unbalanced stoppages and excessive noise from the suspension area

• Disconnect power and water; wear gloves and eye protection
• Support the tub to relieve spring tension before removing suspension components
• Transfer any brackets or clips from the original part; install in the same orientation
• After reassembly, level the washer and run a rinse/spin test to stability

The Heater and Housing Assembly is an OEM part for GE electric dryers. As the main heat source, the heater coil works together with the housing to effectively heat air flowing through the dryer. Precisely maintaining optimal drying temperatures is crucial to the drying process. 

Symptoms of a bad heater and housing assembly include:

• Inefficient or prolonged drying times 
• Excessive lint accumulation inside the housing
• Rust or damage visible on the heater coil
• Odors produced from a burnt-out or shorted heater element

Causes can be normal wear over time, moisture damage if the housing is not cleaned regularly, or an internal short if the heater coil is cracked or broken.

This heater and housing replacement is also compatible with Hotpoint, RCA, and some Kenmore electric dryer models.

This locking clip secures a mating component inside the washer, keeping it firmly attached to its mounting point. Replacing a worn or missing clip restores a snug fit and helps prevent movement, intermittent connections, and noise during operation.

• Retains the designated component securely to its bracket or panel
• Helps prevent vibration-related movement, rattling, or disconnection
• Maintains proper alignment for consistent operation
• Typical signs of failure: cracked or missing clip, part won't stay seated, new looseness around the mount

• Disconnect power and turn off water before servicing
• Access the clip location per your model's service information
• Release and remove the old clip; inspect the mating part for damage or wear
• Seat the new clip fully until it locks; verify the component is secure before reassembly

This electronic water level pressure switch senses air pressure from the wash tub and tells the control when to start and stop filling. Replacing a failed switch restores proper fill levels and helps cycles advance reliably. What it does:

• Monitors tub water level via an air hose connected to the switch
• Signals the control to start/stop the inlet valves at the correct level
• Enables cycle progression by confirming empty/full status
• Common symptoms: won't stop filling, stops filling too soon, incorrect water level, or water-level error codes

• 1 electronic pressure switch

• Disconnect power and turn off water supply before servicing
• Access the switch in the control console or rear cabinet area (location varies by model)
• Move the pressure hose and wire connector(s) over one at a time; ensure airtight hose fit and proper routing without kinks
• Inspect the hose and air dome for cracks, kinks, or blockages; clear or replace if needed

This replacement cover fits the washer's front service door. It restores a clean, finished look and helps shield the service compartment from dust and debris when the original cover is cracked, loose, or missing.

• Covers the service opening to protect internal components from debris and accidental contact
• Restores cabinet appearance by concealing the service area
• Replaces a broken, warped, loose, or missing cover
• Common symptoms: cover won't stay closed, visible cracks, rattling, or a missing access cover

• Disconnect power and turn off water before servicing
• Remove the damaged cover
• Align the new cover with the existing hinge/tabs and secure per your model's configuration
• Confirm proper closure and clearance before restoring power

This spring cover protects and retains a mechanism spring inside your washer. Replacing a cracked or missing cover helps keep the spring seated, limits debris intrusion, and supports smooth, reliable movement of the associated control, latch, or linkage.

• Shields the spring and helps keep it properly seated in its pocket
• Reduces friction and wear that can lead to premature spring failure
• Supports consistent return action for the related control, latch, or lever
• Typical symptoms include a missing/broken cover, exposed spring, rattling, or erratic operation

• Unplug the appliance and turn off water before servicing
• Access point varies by model; photograph spring/cover orientation before removal
• Control the spring during disassembly to prevent sudden release
• Ensure the cover is fully seated; test operation before final reassembly

This selector button mounts on the control panel and presses the underlying switch to choose a cycle or option. Replacing a cracked or sticky button restores smooth, reliable selections and a clean, finished look to your appliance.

• Provides the user interface to actuate the selector switch
• Allows selection of cycles or options from the control panel
• Helps resolve issues like a button that's cracked, loose, stuck, or not engaging the switch
• Restores proper feel and consistent operation when making selections

• Disconnect power before servicing.
• Access the control panel and release the old button's retaining tabs or fasteners.
• Align the new button with the switch stem and snap/seat it fully; transfer any original clip or trim if used.
• Reassemble the console and test button travel and engagement.

This adjustable leveling leg supports and stabilizes your washer. Replacing a worn or missing foot helps the appliance sit flat on the floor, reducing rocking, vibration, and noise for smoother, safer operation. What it does:

• Threads into the base to set height and level the cabinet
• Provides a stable contact point with the floor to minimize movement
• Helps address excessive vibration, rattling, "walking," and out-of-balance issues when the washer isn't level
• Direct replacement for a damaged or missing leveling leg

• 1 leveling leg

• Disconnect power and water before servicing; move the appliance carefully to access the foot
• With assistance, tip or raise the unit as needed to reach the leg safely
• Unscrew the old leg; thread in the new leg by hand and adjust until the washer is level front-to-back and side-to-side
• Tighten the lock nut and recheck stability; run a test cycle to verify

Bleach funnel directs liquid bleach from the washer dispenser into the wash tub for even distribution and helps reduce spills, pooling, and bleach odor. Designed to replace cracked, clogged, or worn dispenser funnels. What it does:

• Directs bleach into the wash tub for consistent dispensing and mixing during the wash cycle.
• Helps prevent bleach pooling, dispenser leaks, and blockages that can cause odors or uneven bleaching.
• Replaces damaged or deteriorated funnels; common symptoms include visible cracks, leaking, or persistent bleach residue in the dispenser area.

• Disconnect power to the appliance before servicing to reduce risk of shock or injury.
• The funnel typically seats or snaps into the dispenser housing.
• Inspect and clean surrounding dispenser components before installing the new funnel; rinse the part to remove any manufacturing residue.
• Handle concentrated bleach with care—wear gloves and follow bleach safety instructions.

This support sensor board is the OEM electronic interface that links appliance sensors to the main control, restoring reliable sensor reporting and helping stop sensor-related errors or intermittent operation after a failed board. What it does:

• Routes sensor signals to the main control so readings are interpreted correctly
• Supports normal sensor communications and helps prevent intermittent or erratic behavior
• Common symptom linkage: sensor error codes, incorrect or fluctuating sensor readings, or intermittent unit operation
• Used as a direct replacement for a failed or damaged sensor interface board

• Disconnect power to the appliance before starting any work to avoid shock or injury
• Ground yourself and avoid touching circuit traces or connector pins to prevent ESD damage
• Verify connector seating and routing of any harnesses; re-check connections before restoring power

Package of 12