Hsh25gfbb Bb Parts

Restore reliable ice dispensing with this ice dispenser bucket. It holds the icemaker's ice supply and interfaces with the dispenser drive so cubes or crushed ice can feed smoothly through the chute when you press the dispenser lever.

• Holds ice produced by the icemaker and positions it for dispensing
• Engages with the drive to move ice toward the chute
• Can help resolve weak/no ice dispensing or frequent ice jams
• Common failures include cracks, broken tabs, or worn drive engagement points

• Unplug the refrigerator and wear cut-resistant gloves before servicing
• Remove the old bin from the freezer, empty it, and slide in the new bucket; ensure the drive coupling fully engages
• Restore power, allow the icemaker to produce ice, and test dispensing

This freezer door gasket replaces the perimeter seal on the freezer door. It restores a tight closure that keeps cold air in and moisture out, helping maintain proper temperature and reduce frost and condensation around the door. What it does:

• Seals the gap between the freezer door and cabinet to contain cold air and block humid room air
• Replaces a cracked, torn, shrunken, or warped gasket that no longer seals properly
• Helps address frost or ice near the door opening, moisture on the gasket, rising freezer temps, or a door that won't stay fully closed
• Supports consistent cooling and reduces air leaks that can lead to longer run times

• One freezer door gasket

• Unplug the refrigerator before servicing
• Warm the new gasket with hot water or low heat to relax shipping folds; do not overheat
• Remove the old gasket and clean the sealing surfaces; seat the new gasket fully in the door channel, starting at the corners
• Close the door and check for uniform contact (paper/dollar-bill test); allow the gasket to conform over 24 hours

This armature kit is the moving plunger and linkage operated by the dispenser solenoid. It opens and closes the ice chute door during dispensing and helps it seal when idle to reduce frost and warm-air leaks.

• Converts the solenoid's electrical action into mechanical movement for the dispenser ice chute door
• Helps maintain a proper seal to limit frost and moisture around the dispenser
• Typical symptoms: ice won't dispense; chute door won't open/close; frost/ice buildup at the chute; loud buzzing or clicking from the dispenser area
• Wear or sticking of the armature/spring can hinder movement and affect dispenser operation

• Unplug the refrigerator and shut off water to the dispenser before servicing
• Access the dispenser mechanism in the door; remove trim/control panel per your model's service information
• Note the orientation of the armature, spring, and linkage; transfer components one-for-one to the new kit and secure hardware
• Verify the solenoid plunger moves freely, reassemble, restore power, and test dispenser operation

This screw is a genuine General Electric part, sold individually. This screw can be used as a replacement part for a refrigerator. A screw can suffer damage in the lifespan of a refrigerator. It can also be easily lost or misplaced. Screws are small parts and are usually installed in multiples to ensure components are reliably attached, so one screw loosening or going missing might not necessarily affect the operability of the refrigerator. However, if the components loosen or the screw suffers damage that strips the part, such as punctures or erosion to the metal material from general wear and tear or from a direct impact, the screw should be removed and replaced with this genuine OEM replacement part. This is an OEM part sourced directly from the manufacturer, and it is sold individually. This screw is compatible with the following appliance brands: General Electric, Hotpoint, RCA, and Americana.

This refrigerator lamp socket holds an E12-base appliance bulb and provides the electrical connection for the light fixture. Replace it when the light won't turn on or flickers despite a known-good bulb and functioning door switch.

• Secures an E12 (candelabra) bulb and supplies power to it
• Works with the door/light switch to illuminate the compartment or dispenser area
• Typical failures include heat damage, cracking, or internal contact wear
• Symptoms: no light, intermittent flicker, or a bulb that won't seat firmly

• Disconnect power to the refrigerator before servicing
• Remove any lens/cover, note wire placement, and install the new socket in the original orientation
• Use an E12-base appliance bulb with the wattage specified on your model's rating label
• Restore power and verify operation with the door switch

This fan-mount grommet fits the evaporator or condenser fan assembly to isolate vibration and keep the motor aligned. Replacing a worn grommet can quiet rattles and prevent the fan blade from rubbing the housing. What it does:

• Isolates the fan motor from its bracket to reduce vibration and operating noise
• Helps maintain proper fan motor and blade alignment/clearance
• Replaces cracked, flattened, hardened, or missing grommets
• Typical symptoms: rattling, buzzing, or vibration sounds from the freezer or rear machine compartment

• 1 fan motor grommet

• Disconnect power before servicing; pull the refrigerator forward for rear access if needed
• Evaporator fan: remove the freezer's rear panel; condenser fan: remove the rear service panel
• Support the motor, remove the fan blade and mounting hardware as needed, replace the grommet, and reassemble
• Ensure the fan spins freely and does not contact the shroud before restoring power

This compressor-mounted start device combines the start relay and overload protector. It helps the compressor start reliably and safeguards it from overheating, supporting consistent refrigerator cooling performance. What it does:

• Provides the initial boost to start the compressor, then disengages once it's running
• Protects the compressor circuit by opening if current draw or temperature is too high
• Common symptoms of failure: refrigerator/freezer warm, compressor won't start, repeated clicking, brief humming then shutoff, intermittent cooling
• Restores normal compressor starts when the original device has failed

• One TSD-2 compressor start device assembly

• Disconnect power before service; work in a dry area and follow manufacturer safety guidance
• Access the compressor compartment and note wire positions/terminal layout before removal
• Pull off the old device; push the new device fully onto the compressor pins; transfer wires one at a time to matching terminals
• If your model uses a run capacitor or retaining clip, move and reconnect them exactly as originally configured

Water line from water valve up to icemaker fill tube.

The recess door retainer secures the dispenser's ice chute flapper in the refrigerator door. Replacing a cracked or missing retainer restores proper flapper pivot and sealing to help reduce frost buildup and air leaks around the dispenser.

• Holds the recess/ice door on its pivot within the dispenser assembly
• Helps the flapper close fully to seal the ice chute
• Restores smooth open/close action of the dispenser door
• Common symptoms: loose or fallen flapper, poor chute seal, frost or condensation in the dispenser area, and ice clumping near the chute

• Unplug the refrigerator before servicing the dispenser
• Carefully remove the dispenser bezel/control panel to access the ice chute door assembly
• Note spring orientation and retainer position; transfer components to the new retainer
• Verify flapper movement and seal before reassembly and restoring power

Restore solid storage space with this fixed shelf module for your refrigerator. It replaces a damaged or missing shelf so you can organize groceries securely and use your fridge's capacity the way it was designed.

• Provides a stable, level surface for food and containers inside the refrigerator compartment
• Fixed, non-slide design stays in place once installed
• Factory-fit geometry helps prevent wobbling and tipping
• Typical symptoms: cracked or broken shelf, broken mounting tabs, shelf won't seat or sit level, missing shelf

• Remove items from the area and take out the old shelf; wear cut-resistant gloves and handle carefully
• Align the new shelf with the side supports/slots and lower or slide into place
• Verify the shelf is fully seated and level before loading items
• Disconnect power if working near interior lights or electrical components

Size: 8-18 AB TSQ 5/8 SS

This is a grommet and it is intended for use on refrigerators and freezers. This is a genuine replacement part made by General Electric. A new grommet might be needed if the current one is visibly worn out or damaged in any way. If there are noises from vibration coming from the lower back area of the fridge there might be need for a new grommet. This is an OEM part sourced directly from the manufacturer, and it is sold individually. It is compatible with refrigerators and freezers, or units with a compressor and is made by General Electric.

This freezer shelf restores lost storage and organization inside your freezer. Replace a broken or missing shelf to add a stable level for stacking and separating items so food stays accessible and easy to arrange.

• Provides an additional storage level inside the freezer
• Helps organize and separate frozen foods for quicker access
• Replaces a cracked, bowed, or missing shelf
• Seats into the freezer's existing side supports for a secure fit

• Remove food from the area before replacing the shelf
• Handle carefully; edges and corners can be sharp
• Align with the side supports and ensure the shelf is fully seated on both sides
• Distribute weight evenly; avoid overloading the shelf

This small guide sits at the icemaker fill area and manages the water stream. It directs incoming water into the fill cup and channels any excess safely away to help prevent splashing, leaks, and ice buildup inside the freezer.

• Guides the icemaker fill stream into the fill cup/funnel during the fill cycle
• Diverts stray or excess water to the overflow path to reduce spills
• Helps prevent leaks, sheets of ice, and clumped cubes under the icemaker
• Clues it may be needed: cracked, warped, or missing guide; water dripping from the fill area

• Disconnect power and turn off the water supply before servicing
• Remove ice bin and any covers to access the icemaker fill area
• Unclip/unscrew the old diverter; align and secure the new part to the fill cup/tube
• Restore water and power; run a test fill and check for leaks

This ice maker stripper is the front comb that helps release cubes from the ejector during harvest. It guides ice cleanly into the bin to reduce jams and keep ice production running smoothly. What it does

• Strips ice cubes off the ejector fingers as the ice maker cycles
• Directs cubes into the bucket, helping prevent jams and cube bridging
• Wear, cracks, or warping can cause cubes to stick, spill, or clump
• Symptoms include cubes piling at the front, clicking during harvest, or reduced/no ice

• 1 ice maker stripper

• Disconnect power and shut off water before servicing
• Remove the ice bin and access the ice maker front (remove cover if present)
• Release the old stripper (tabs/screws), align the new stripper with the ejector fingers, and seat it fully
• Reinstall cover and bin; restore power and allow a full cycle to verify operation