Jed2295kes Parts

This switch seal is a small rubber gasket that protects a control or door switch from moisture and debris, helping maintain reliable operation and prevent damage to the switch assembly. What it does:

• Creates a moisture- and dust-resistant barrier around a switch to reduce shorting and corrosion
• Helps keep switches operating smoothly by blocking contaminants that cause sticking or intermittent contacts
• Supports safe electrical performance by keeping water away from switch terminals and housings
• Common symptom linkage: switch malfunction, intermittent control, or moisture-related failures near switch area

• Disconnect power to the appliance before inspecting or replacing the seal
• Remove surrounding trim or components carefully to avoid damaging the switch or housing
• Confirm correct orientation and full seating of the seal during reassembly for an effective barrier
• If the switch shows damage or corrosion, replace the switch assembly as well

This infinite switch controls the heat level for a stove's top burner, letting the burner cycle through a range of settings for precise cooking. Replaces a failed burner control to restore adjustable heat on the cooktop. What it does:

• Regulates electrical power to a single top burner to change flame/heat between low and high settings
• Replaces a worn or faulty control that causes burners to stay off, not heat, or only work on fixed settings
• Helps resolve intermittent or unresponsive burner control behavior and uneven heating
• Matches OEM function for electronic/mechanical infinite control circuits used on many electric ranges

• Disconnect power to the appliance before starting any repair to avoid electric shock
• Access typically requires removing the cooktop or control panel
• Inspect wiring and terminal connectors for damage; replace any frayed wires or loose terminals before reassembly

This wire harness routes power and control signals between appliance components, restoring electrical connections for proper operation. It replaces a damaged or worn harness to help resolve intermittent power, control failures, or component non-responsiveness. What it does:

• Provides the factory wiring paths for power and signal distribution between control and components
• Restores lost or intermittent electrical connections caused by frayed, burned, or broken wires
• Helps stop symptoms such as no power to a module, controls not responding, or certain functions failing
• Matches OEM connector groups and wire lengths for a direct replacement

• One wire harness assembly

• Replace only with the exact OEM harness; disconnect power before beginning work
• Take photos or label connections before removal to ensure correct reassembly
• Secure harness away from heat sources, sharp edges, and moving parts to prevent future damage

This genuine replacement screw secures appliance components so panels, brackets, and assemblies stay tight and properly aligned. Replacing stripped, rusted, or missing hardware restores a solid fit and helps prevent rattles, shifting, or looseness over time.

• Fastens panels, brackets, and internal parts to maintain proper alignment
• Helps resolve issues caused by missing or damaged screws
• Restores secure mounting after service where original hardware is lost
• Use when threads are stripped or the screw head is damaged and won't tighten

• Disconnect power; turn off gas supply if applicable before servicing
• Match screw location and length to your model's parts diagram for correct placement
• Start threads by hand to avoid cross-threading; use the correct driver bit
• Snug firmly but do not overtighten to prevent damage to mounting points

This switch bracket mounting seal replaces a worn or damaged seal that cushions and protects the door or control switch mounting area. It helps keep the switch assembly seated and reduces debris and moisture intrusion for reliable operation. What it does:

• Seals the switch bracket mounting area to protect the switch from lint, dust and moisture
• Helps keep the switch properly positioned for accurate door or control sensing
• Can prevent intermittent or failed switch contacts caused by contamination or misalignment
• Useful when replacing a brittle, torn or missing mounting seal during switch or door repairs

• Disconnect power to the appliance before starting any repair
• Remove the door or panel per service instructions to access the switch bracket area
• Fit the seal into the bracket groove or around the switch housing, ensuring full seating without stretching
• Inspect adjacent clips or screws and reuse or replace as needed; test the switch function after reassembly

This replacement infinite control knob lets you precisely adjust the heat level on an electric cooktop or range surface element. It restores a secure grip and clear pointer for accurate temperature control during cooking. What it does:

• Fits onto an infinite (infinite-tap) surface element control shaft to select heat settings
• Provides a clear pointer for accurate selection of low-to-high settings
• Replaces worn, cracked, or stripped knobs that slip or won't turn
• Helps stop intermittent or unreliable control caused by a damaged knob

• Remove power to the appliance before servicing for safety
• Pull off the old knob straight from the control shaft; push the new knob onto the shaft until secure
• Confirm proper fit and full range of motion before restoring power

The Vent Access Cover is an OEM part for Whirlpool cooktops. It is the rear ventilation cover located at the back of the oven cavity. This cover plays an important role in properly directing the exhaust of combustion gases and ventilating heated air outside of the home.

Causes of a bad vent cover can include damage from impact, warping due to overheating, or broken mounting points interfering with a tight seal. 

Symptoms of a bad vent cover include:

• Incomplete combustion of fuels resulting in efficiency and safety issues  
• Reduced airflow and ventilation compromising the oven function
• Gaps or openings that allow exhaust recirculation or intrusion of debris

 This OEM Whirlpool vent cover is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This cooktop surface assembly replaces the top cooking surface to restore a smooth, stable area for burners and cookware. It helps maintain a clean look and proper fit for your cooktop components. What it does:

• Replaces a cracked, chipped or otherwise damaged cooktop surface
• Provides a stable mounting surface for burners, grates, and controls
• Restores a flush, sealed cooking area to help contain spills
• Helps eliminate rattling or misalignment caused by warped surfaces

• Disconnect power (and gas if applicable) before beginning any work
• Handle the surface carefully—glass and enamel parts can chip or crack
• Some installs may require removing adjacent trim or control panels; follow OEM instructions

This glass smooth-surface cooktop replaces a damaged or worn smooth-top surface to restore a flat, easy-to-clean cooking area and ensure burners sit and heat properly. It's designed for direct fit on compatible range/cooktop units. What it does:

• Provides a durable, smooth glass cooking surface for electric radiant elements
• Restores stable support and alignment for heating elements or burners
• Helps eliminate cracks, chips, or burn-throughs that can cause uneven cooking
• Makes cleanup easier compared with coil-style cooktops

• One glass smooth-surface cooktop panel

• Installation requires removing the cooktop assembly and disconnecting power at the breaker; follow the manufacturer service manual
• Handle the glass carefully to avoid chipping; use appropriate suction cups or protective gloves
• Verify element alignment and gasket placement before re-securing the cooktop
• If damaged wiring or mounting hardware is found, replace those components per OEM guidance

This replacement control knob restores a secure grip and clear pointer for selecting heat and function settings on compatible Whirlpool appliances. It provides a precise, easy-to-read control surface so you can operate your appliance confidently. What it does:

• Replaces a worn, cracked, or missing control knob to restore manual control
• Fits on standard splined control shafts to select temperature or function positions
• Helps resolve symptoms like loose knob movement, slipping on the shaft, or illegible setting indication
• Matches OEM shape for correct fit and tactile feedback

• Pull off the old knob by hand; align the splines and push the new knob fully onto the shaft until it seats
• If knob is tight or hard to remove, power off the appliance and before using tools
• Do not overtighten or force onto the shaft; avoid using excessive heat or solvents
• If electrical access behind the panel is required, disconnect power first and follow all safety guidelines

This plenum mounting screw kit contains the hardware used to secure the plenum assembly so panels sit correctly and vibration is reduced. Ideal when original plenum fasteners are missing, stripped, or corroded. What it does:

• Provides the screws and fasteners needed to attach the plenum to the cabinet or blower housing
• Restores proper fit and alignment of the plenum and adjacent panels
• Helps stop rattling or vibration caused by loose or missing fasteners
• Prevents gaps that can affect airflow or allow small parts to move

• Disconnect power and follow all safety precautions before beginning repairs
• Use the matching screw types and lengths; do not overtighten to avoid stripping threads
• Keep removed hardware organized to verify replacement parts match during reassembly
• If panels or threads are damaged, assess for repair or replacement to ensure secure mounting

This low-voltage transformer supplies control voltage to the appliance's user interface and control board so displays, touch controls and dispensers operate correctly. Replacing a failing transformer restores reliable low-voltage power to the control system. What it does:

• Converts line voltage to the low-voltage control supply used by the control board and user interface
• Allows control panel, lights, dispensers and related electronics to receive the proper control voltage
• Failing part may cause unresponsive controls, blank displays, or intermittent operation of electronic features
• Matches OEM function and mounting for a direct replacement when the original transformer has failed

• Disconnect power to the appliance before servicing to avoid electric shock
• Handle wiring terminals carefully; secure all wire connections and restore any mounting clips or screws
• After installation, restore power and test all electronic controls and displays for proper operation