Jenn-Air Jed 8430 Parts

This grease filter traps airborne grease and cooking residue from the vent airstream. Replacing a worn or clogged filter helps restore airflow, protects the blower and ducting, and reduces greasy buildup on surrounding surfaces.

• Captures grease particles before they reach the fan and ductwork
• Helps maintain proper ventilation performance
• Common symptoms of a bad filter: lingering odors, poor venting, visible saturation or damage, rattling or loose fit
• Regular replacement supports cleaner operation and effective exhaust

• Disconnect power to the hood or microwave before servicing
• Access the filter from the underside; release the latch or fastener and remove the old filter
• Install the new filter in the same orientation as the original; ensure it is fully seated and secured
• Do not operate the vent without a grease filter in place

This is a radiant surface heating element for smooth-top electric ranges. It replaces a failed burner to restore up to 1300 watts of even heat and dependable temperature control under the glass-ceramic cooktop. What it does:

• Generates radiant heat beneath the glass surface when powered by the burner control
• Restores proper heating if a burner will not heat, heats unevenly, or cycles off too quickly
• Helps eliminate long heat-up times caused by a weakened or open element
• Replaces elements with visible damage such as broken ribbons, burn spots, or charred terminals

• 1 radiant surface element (1300W)

• Disconnect power at the breaker or unplug the range before servicing
• Allow the cooktop to cool fully; lift/prop the glass top to access the element
• Note wire positions; transfer any mounting brackets/clips from the old element and reconnect wires securely
• Handle the element carefully and avoid stressing the ribbon; reassemble and test the burner before finalizing

This blower wheel mounts on the drive motor and pushes air through the dryer drum and out the exhaust. Replacing a worn wheel restores proper airflow for consistent drying and helps prevent overheating and nuisance shutdowns. What it does:

• Moves air across the heater, through the drum, and out the vent to remove moisture
• Helps maintain proper airflow and temperature inside the dryer
• Common failure symptoms: reduced or no airflow at the exterior vent, longer dry times, unusual scraping/thumping or vibration from the blower area, or overheating/shutoff
• Cracked fins or a stripped hub can cause the wheel to slip on the motor shaft

• 1 blower wheel

• Disconnect power and turn off gas supply before servicing
• Access the blower housing per your model's service instructions; remove the retaining hardware and replace the wheel in the same orientation
• Clean lint from the blower housing and vent path; inspect the motor shaft and blower seal for wear
• Reassemble and verify the wheel spins freely without rubbing; check airflow at the exterior vent

This blower speed switch lets you select the blower/fan speed to restore proper airflow control in your appliance. It replaces a worn or faulty speed selector so the blower will respond correctly when you change settings. What it does:

• Controls the blower/fan speed so the appliance can run at selectable airflow levels
• Replaces a switch that is stuck, unresponsive, or only running at one speed
• Restores reliable electrical connection between the control circuit and blower motor
• Helps eliminate intermittent fan operation or loss of speed selection

• Disconnect power to the appliance before starting any repair.
• Verify wiring placement and retain original fasteners; wiring diagram for correct connections.
• Handle terminals carefully to avoid bending or damaging contacts.

This radiant surface element uses a ribbon-style heater to provide even heat beneath a glass-ceramic cooktop. Replace a failing burner to restore consistent, reliable heating on the affected cooking zone.

• Provides radiant heat to one surface burner zone beneath the glass top
• Works with the surface control to regulate cooking temperature
• Common fix for a burner that won't heat, heats unevenly, or takes too long to heat
• Replace if the element shows an open circuit when tested for continuity

• Disconnect power at the breaker or unplug the appliance before servicing
• Allow the cooktop to cool completely; support the glass top per service instructions to access the element
• Transfer wires from the old element to the new one position-by-position; secure using existing brackets
• Avoid touching the element surface; test operation before reassembly

The LF Surface Heating Element is an OEM part for Whirlpool ranges. It is a top burner element responsible for generating heat on the cooktop for cooking. This element ensures consistent and even heating when in use, allowing for efficient cooking performance.

Causes of a bad surface heating element can include normal wear and tear over time, electrical failures, or damage due to overheating or spills. A faulty element may also result from a damaged terminal block or loose connections.

Symptoms of a bad surface heating element include:

• The burner not heating at all
• Uneven heating or hot spots
• The element sparking or producing a burning smell
• Visible damage such as cracks or breaks in the coil

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This dual surface element infinite switch controls power to an electric cooktop or range's dual radiant burner. It restores precise heat selection and lets you choose inner-only or full dual-ring operation when the original switch fails.

• Regulates power cycling to maintain the selected heat level on a dual radiant element
• Selects between inner-only and dual-ring operation on compatible burners
• Common failure symptoms: no heat, only runs on high, cannot adjust temperature, burner won't shut off, dual feature won't engage
• Restores consistent, controllable surface cooking performance

• Disconnect power at the breaker before servicing—this is a high-voltage component
• Pull the control knob and open the control panel or rear cover to access the switch
• Photograph/note wire locations; move wires to the new switch one at a time
• Secure the switch, reassemble, restore power, and test both inner and dual-ring settings

Razor blade scraper.

This foam tape is used to seal and cushion mating surfaces in your appliance. Replacing a worn strip restores a snug fit, helps reduce noise, and helps maintain proper airflow, heat, or moisture control where specified by the manufacturer.

• Provides a compressible seal between components per the unit's parts diagram
• Cushions panels and trim to reduce vibration, buzzing, or rattling
• Helps prevent air, steam, or heat leaks at joints and seams
• Replace if the original tape is torn, flattened, missing, or contaminated

• Disconnect power and shut off gas/water as applicable; allow the appliance to cool before service
• Note the original tape placement; remove old material and residue, then clean and dry surfaces
• Apply per the service manual; avoid stretching; press evenly to ensure full contact
• If the OEM procedure calls for trimming, cut carefully to length and avoid gaps or overlaps

This infinite switch is the user control that regulates heat levels for a stove's top burner, restoring variable temperature control for smooth cooking. It fits into the cooktop control assembly and replaces a worn or non-responsive controller. What it does:

• Regulates electrical power to a single surface burner so you can set low-to-high heat
• Replaces a switch that sticks, skips settings, or produces no heat
• Helps stop unpredictable burner behavior like intermittent operation or failure to cycle
• Works with manual knob controls to provide stepped variable heat

• Disconnect power to the range at the breaker before servicing to avoid shock
• Access typically requires removing the cooktop or control panel—refer to your model's service guide
• Inspect and match terminal configuration before installation; secure all wire connections

The Filter is an OEM part for Whirlpool cooktops. This part is responsible for trapping grease and other airborne particles, ensuring that your kitchen remains clean and free from unwanted odors during cooking. It effectively captures grease and prevents it from accumulating in the exhaust system.

A bad grease filter can occur due to clogging, damage, or excessive wear. If you notice symptoms such as poor ventilation, persistent cooking odors, or visible grease buildup in the downdraft vent, it may be time to replace the worn-out or clogged grease filter with this genuine OEM part.

Symptoms of a bad grease filter include:

• Poor ventilation and airflow
• Lingering cooking odors
• Visible grease accumulation in the downdraft vent

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
 

This small spring applies tension to hold an element in the correct position within the appliance, helping maintain reliable contact and stable operation. Replacing a worn spring can restore proper element support and performance.

• Provides push tension to keep the element seated and secure
• Helps prevent intermittent heating due to poor element contact
• Common signs include rattling, poor element stability, or intermittent heat

• Disconnect power and allow the unit to cool before service
• Access the element mounting area; note original spring placement
• Use needle-nose pliers to remove and install the spring carefully
• Inspect adjacent clips and wiring; replace damaged parts as needed

The Grease Filter is an OEM part for Whirlpool downdraft cooktops. It is responsible for removing grease and other cooking residue from the air before it is circulated back into the kitchen.

Causes of a bad grease filter include excessive grease buildup that prevents proper airflow and filtration. Grease filters should be cleaned regularly according to the manufacturer's recommendations.

Symptoms of a grease filter that needs replacement include:

• Reduced or inefficient airflow while in use
• Visible grease buildup or clogging of the filter screens

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Blower Motor is an OEM replacement part for Whirlpool cooktops that feature a downdraft ventilation system. It is responsible for exhausting smoke, odors, and steam from your cooking area. It provides powerful and efficient ventilation, keeping your kitchen fresh and free from unwanted cooking odors.

A bad blower fan assembly can occur due to regular use, mechanical failures, or motor malfunctions. If you notice symptoms such as weak airflow, excessive noise, or the fan not working at all, it may be time to replace the blower fan assembly.

Symptoms of a bad blower fan assembly include:

• Weak airflow
• Excessive noise
• Fan not working at all

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
 

This control board relay replaces the relay on the appliance's electronic control to restore reliable switching of high-current components. It helps the control safely turn motors, heaters and compressors on and off as commanded. What it does

• Acts as the high-current switching relay mounted to the electronic control board
• Enables the control board to power motors, heaters or compressors when needed
• Can resolve intermittent or no-operation symptoms caused by a failed relay
• Stop clicking, non-start, or loss of specific functions when replaced

• Disconnect power to the appliance before starting any repair.
• Handle the relay and control board by the edges; avoid touching circuitry.
• Verify harness connectors seat fully and wires are undamaged before reassembly.
• After installation, restore power and run a short test cycle to ensure proper operation.

Color: Black