Kdtm354dsso Parts

The Dishwasher Vent Assembly is an OEM part for Whirlpool dishwashers. Located at the top corner of the dishwasher, it contains openings to expel heat and excess moisture during cycles. Venting helps maintain proper temperature levels inside cabinetry and prevents build-up that could damage surrounding countertops or flooring over time. 

Causes of vent assembly failure include clogs from detergent residue or mineral deposits collecting in ventilation slots. Over-zealous cleaning may also damage vent surfaces reducing air flow.

Symptoms of a restricted vent include:

• Puddles or leaks around the dishwasher seal
• Slow or incomplete drying at the end of cycles
• Steam leaving through partially closed doors

This is a genuine Whirlpool OEM replacement, this part is also compatible with Maytag, Jenn-Air, and some KitchenAid models.

The Water Level Switch Bracket is an OEM part for Whirlpool dishwashers. This bracket holds the water level switch in place. The water level switch is a part that monitors and regulates the amount of water inside the dishwasher.

Causes of a bad Water Level Switch Bracket can include physical damage that may occur during use or installation, corrosion over time due to exposure to moisture and detergents, or general wear that compromises its ability to securely hold the water level switch.

Symptoms of a bad Water Level Switch Bracket include:

• The dishwasher not filling with the correct amount of water
• Water leaking from the dishwasher if the switch moves out of position and fails to regulate the water level accurately.
• Unusual noises during the fill cycle

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Side Mounting Bracket Kit is an OEM part for Whirlpool dishwashers. It provides a secure and stable installation by mounting the dishwasher to the adjacent cabinetry or walls.

Causes of a bad Side Mounting Bracket Kit can include missing or damaged components, improper installation, or wear and tear over time.

Symptoms of a bad Side Mounting Bracket Kit include:

• The dishwasher rocking or shifting during operation
• Gaps or spaces between the dishwasher and surrounding cabinetry
• Potential safety hazards due to an improperly secured dishwasher

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Nut is an OEM part for Whirlpool dishwashers. This nut secures the float switch, a key component in regulating the water level within the dishwasher. The float switch ensures your dishwasher does not overfill by triggering the water to stop once it reaches a certain level. 

Over time and with regular use, the nut that holds the float switch in place can become loose or damaged. This could potentially allow water to seep through gaps, leading to leaks, or could cause the float switch to malfunction, affecting the dishwasher's ability to regulate water levels accurately.

Symptoms of a faulty Nut include:

• Water leaks from the base of the dishwasher 
• The dishwasher overfills or underfills 
• Unusual noises during operation 

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Hose Clamp is an OEM part for Whirlpool washing machines. This clamp secures the hose in place, ensuring a tight connection and preventing leaks during operation. It is essential for maintaining the integrity of the washing machine's water system, securing hoses that carry water to and from the washer.

Common causes of a bad hose clamp include rust, physical damage, or loosening from repeated tightening and loosening.

Symptoms of a bad hose clamp include:

• Water leaks around the hose connection points
• The hose slipping off the fitting
• Visible rust or wear on the clamp
• Difficulty in tightening the clamp to secure the hose

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models.

The Upper Dishrack is an OEM part for Whirlpool dishwashers. This dishrack is designed to hold dishes, glasses, and other items securely in the upper part of the dishwasher during the wash cycle, allowing for effective cleaning and efficient use of space.

Causes of a bad upper dishrack can include regular wear and tear, damage from heavy or improperly loaded items, and rust or corrosion from prolonged exposure to water and detergents.

Symptoms of a bad upper dishrack include:

• Broken or missing tines that prevent items from being held securely
• Rust or corrosion on the dishrack
• Difficulty sliding the dishrack in and out of the dishwasher
• The dishrack not fitting correctly or falling off its tracks

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Tub Inlet Gasket is an OEM part for Whirlpool dishwashers. It ensures a watertight seal at the point where water enters the tub, preventing leaks and maintaining efficient water flow during the wash cycle.

Causes of a bad tub inlet gasket include wear and tear from regular use, damage from harsh cleaning chemicals, or drying out and cracking due to age.  

Symptoms of a bad tub inlet gasket include:

• Water leaking from the front or bottom of the dishwasher
• Poor cleaning results due to insufficient water pressure
• Visible cracks or wear on the gasket
• Unusual noises from the dishwasher during the filling cycle

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

Restore strong spray performance with this circulation pump and motor assembly. It drives wash water through the spray arms, helping your dishwasher clean effectively and run more quietly when the original pump is worn or seized.

• Circulates wash water through the spray arms during wash and rinse cycles
• Maintains proper water pressure for effective cleaning coverage
• Common failure signs: poor cleaning results, spray arms not spinning, loud humming/grinding, or leaks from the pump area
• Replaces a non-running or intermittently running wash motor

• Disconnect power and shut off water supply before servicing
• Access is typically from the front underside; remove the toe panel/kick plate to reach the pump at the sump
• Expect residual water; place a towel or pan before loosening clamps/locking ring and electrical connectors
• Ensure the sealing surface is clean, seat the assembly fully, lock in place, reconnect hoses/wiring, and check for leaks on test run

This is a dishwasher circulation pump. The circulation pump is located inside the dishwasher and includes an impeller and a motor. The purpose of the circulation pump is to provide a means for water to be forced into and out of the wash arms. If this part is damaged or faulty, the dishwasher may not clean properly or may make much more noise than is expected.The first step to replace the circulation pump is turning off the water supply and electrical power to the appliance. Take off the spray arms before removing the toe panel and bottom access panel. Pull the dishwasher away from the wall before removing the drain pump. Use a towel to catch any water. Next, remove the circulation pump and the motor assembly. Transfer the small parts to the replacement part and install it into the dishwasher. Reassemble and reconnect water and power before using the appliance.Made for dishwashers manufactured by Kenmore, Whirlpool, and KitchenAid, the circulation pump is sold on an individual basis. This is an authentic OEM replacement part that is directly sourced from the manufacturer.

The Tube-Feed is an OEM part for Whirlpool dishwashers. This part directs water from the pump to the spray arms, ensuring proper water flow and distribution during the wash cycle. 

Common causes of a faulty tube-feed include clogs from food debris, cracks or breaks due to wear and tear, or damage from improper installation or handling.

Symptoms of a bad tube-feed include:

• Reduced water pressure from the spray arms
• Incomplete or poor cleaning results
• Visible cracks, holes, or damage to the tube
• Leaks or water pooling inside the dishwasher

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Door Hinge Assembly is an OEM part for Whirlpool dishwashers. This hinge assembly is responsible for attaching the dishwasher door to the main body, allowing it to open and close smoothly while maintaining a proper seal when shut. 

Causes of a bad door hinge assembly can include regular wear and tear, damage from excessive force or accidental impacts, and corrosion from exposure to moisture and detergents.  

Symptoms of a bad door hinge assembly include:

• The dishwasher door not closing properly or staying open
• Difficulty opening or closing the dishwasher door
• A misaligned dishwasher door
• Unusual noises or resistance when moving the door

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This cover screw secures appliance panels and covers, keeping components protected and aligned. Replace missing, stripped, or corroded screws to restore a tight fit and help eliminate rattles, gaps, or panels that won't stay in place.

• Attaches an access cover or panel to the appliance frame
• Helps maintain proper alignment to protect internal components
• Replaces missing, stripped, or rusted hardware
• Typical signs: loose or rattling panel, cover won't stay secure, damaged or rounded screw head

• Disconnect power before servicing
• Support the panel while removing and installing screws to prevent misalignment
• Start threads by hand to avoid cross-threading; do not overtighten
• Use a matching driver bit to avoid damaging the screw head

The Detergent Dispenser Bracket is an OEM replacement part for Whirlpool dishwashers. Located inside the dishwasher tub along the edge, this bracket securely holds the entire detergent dispenser assembly in place. 

Causes of a bad bracket may be normal wear and tear over time, damage from overloading dishes, or accidental impact affecting the integrity of the plastic.

Symptoms of a bad detergent dispenser bracket include:

• Loose or unstable detergent dispenser  
• Detergent not dispensing or leaking
• Clanking noises coming from inside the tub
• Visible cracks, breaks, or deformations in the bracket 

This OEM Whirlpool part is also compatible with KitchenAid, Jenn-Air, Amana, and some Kenmore and Maytag models.

The Screw Hole Cap is an OEM part for Whirlpool dishwashers. It covers the screw holes, providing a clean and finished appearance while preventing moisture and debris from entering the screw openings. This helps maintain the dishwasher's aesthetic and ensures that screws remain protected from rust and corrosion.

Causes of a bad screw hole cap can include regular wear and tear, accidental impacts, or misplacement during maintenance.

Symptoms of a bad screw hole cap include:

• Missing or loose caps
• Moisture or debris accumulating in screw holes
• Visible wear or damage to the caps

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Hinge Brace is an OEM replacement part for Whirlpool dishwashers. It serves as a supportive bracket anchoring the dishwasher door hinge assembly firmly in place.Note: This part may be different from your original. If your original part was a flat plastic vapor barrier, the new design is a wire. It is a factory design change, the old design is no longer available.

Over time, the hinge brace can degrade due to constant use, heavy loads on the door, or accidental impacts. A faulty hinge brace can result in misalignment or difficulty in operating the dishwasher door.

Symptoms of a bad hinge brace include:

• Loose or unstable door that does not close securely
• Gaps appearing around the door seal during wash cycles
• Broken hinge components from added stress and tension on the door
• Difficulty fully opening or closing the dishwasher door

This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air and some Kenmore models.

Color: Black. Screw for lower toe panel. For Biscuit screw use 3400865, for white screw use WP3400836.