Kdtm404ees1 Parts

This support is a small mounting bracket that secures internal components and helps keep assemblies aligned so your appliance runs quietly and reliably. It replaces worn or broken supports to restore proper fit and stability. What it does:

• Secures internal parts or panels to prevent movement and misalignment
• Reduces vibration and rattling caused by loose or damaged supports
• Helps maintain correct alignment of assemblies for reliable operation
• Prevents further wear on adjacent parts by holding components in place

• Disconnect power (and water if applicable) before starting any repair
• Use common hand tools;
• Handle edges carefully—some components and mounting points may be sharp
• W10647236 matches the part on your appliance before installing

This pump cover replaces the damaged housing that seals and protects the washer's drain pump, helping restore proper water flow and contain leaks. It's a direct-fit service part designed for use with the original pump assembly. What it does:

• Forms the sealed housing around the drain pump and impeller to prevent water leaks.
• Helps direct drained water from the tub into the pump for proper drainage.
• Can resolve symptoms such as leaks under the washer, poor draining, or grinding/noise when the pump area is compromised.
• Replaces cracked or worn pump housings that allow water to escape or reduce pump efficiency.

• Disconnect power and water supply before servicing the washer to avoid shock or flooding.
• Basic hand tools required; some models may require removal of the front or rear access panel to reach the pump.
• Inspect surrounding seals, hoses, and clamps while replacing the cover; replace any damaged components to prevent repeat leaks.

Color: Black

The Control Panel is an OEM part for Whirlpool dishwashers. Located at the top center, it houses the electronic buttons controlling cycle, option, and start selections. 

Causes of a bad control panel are often due to water exposure over time breaking seals or mineral deposits inhibiting proper responses. Physical damage from accidental impacts can also impair functionality.

Symptoms of a bad control panel include:

• Unresponsive or incorrectly functioning buttons
• Inability to toggle options or initiate desired cycles
• LED/display issues such as dimming or non-illumination  
• Physical cracks or loosening of mounting screws

This genuine Whirlpool replacement is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and Kenmore dishwasher models.

This replacement refrigerator door gasket creates a tight seal around the fresh-food compartment door to help keep cold air in and warm, humid air out, improving cooling performance and reducing frost buildup. What it does

• Forms an airtight seal around the fresh-food door to help maintain interior temperature
• Helps prevent warm air and moisture from entering, reducing frost and condensation
• Can reduce compressor runtime caused by a leaking door seal
• Common symptom: visible gaps, tears, or warped edges around the door; uneven cooling or frost along the door perimeter

• One refrigerator door gasket

• Inspect and clean the door flange before installing to ensure a proper seal
• Start installation at the corners and work around the perimeter, pressing the gasket into the channel to seat it evenly
• Warm the gasket slightly if needed to make it more flexible for fit; avoid overheating
• Disconnect power only if required by your refrigerator model and follow all safety precautions

This wire harness routes power and signals between a unit's controls and its components to restore reliable electrical connections. It replaces a damaged or worn harness so controls, motors and sensors can communicate safely. What it does:

• Provides factory-style wiring connections between control board and components.
• Restores power and signal paths to fix intermittent operation or loss of function.
• Helps eliminate burnt, frayed or broken wires that can cause faults or error codes.
• Keeps wiring organized and routed to prevent chafing and short circuits.

• Disconnect power (unplug or shut off breaker) before starting any repair.
• Compare harness and connector shapes to the original before installation.
• Route wires per the cabinet harness channels; avoid pinching or sharp edges.

The Lower Door Seal is an OEM replacement part for Whirlpool dishwashers. This seal runs along the bottom edge of the dishwasher door, creating a tight seal against the tub when closed to contain water inside during cycles.  This seal measures approximately 22 inches in length

Causes of lower door seal failure commonly involve repeated compression stresses from opening/closing actions gradually stiffening the flexible gasket material. Drying out and cracking occurs over years of heat exposure as well.

Symptoms of a worn lower door seal include:

• Water leaking out from beneath dishwasher door during cycles
• Difficulty latching door completely from warped seal edges  
• Visible cracks, splits or brittleness along the length of the seal
• Gaps allowing water intrusion beneath door perimeter

This versatile OEM part is also compatible with select Maytag, KitchenAid, Jenn-Air, Amana, and some Kenmore dishwasher models.

This factory part is a precision ring used within the appliance assembly to position and secure mating components. Replacing a worn, cracked, or missing ring restores proper fit, reduces noise, and helps prevent premature wear or leaks. What it does:

• Provides seating/retention for the specified component in the assembly
• Maintains correct alignment and spacing between parts
• Helps prevent vibration, rubbing, or leaks caused by a loose fit
• Replace if distorted, cracked, corroded, or missing
• Typical symptoms include loose or wobbly parts, scraping/rattling noises, or components slipping out of place

• 1 ring

• Disconnect power and shut off any utilities (water/gas) as applicable before service
• Access the assembly and note the ring's orientation; take reference photos
• Use appropriate hand tools; avoid over-stretching and ensure the ring seats fully in its groove or against its shoulder
• Verify smooth operation of the mechanism before reassembly and testing

This Shield is a protective cover used in select Whirlpool-built appliances. It helps guard nearby components from heat, moisture, and debris so the appliance can operate as designed and nearby parts don't wear prematurely. What it does:

• Shields sensitive wiring, controls, or moving parts from heat, splashes, and debris
• Helps maintain proper airflow/deflection where the shield is installed
• Common symptoms include visible cracks, warping/discoloration, broken tabs, rattling from a loose shield, or a missing/bent shield after service

• 1 shield

• Disconnect power before servicing; also shut off gas or water if applicable
• Note the shield's orientation and reuse existing mounting hardware unless damaged
• Do not bend the shield; verify proper clearance from fans, elements, and moving parts
• After installation, restore power and check for vibration or rubbing noises

This brace connector secures a support brace inside the appliance to help keep internal panels and assemblies aligned and stable. Replacing a worn or damaged connector restores proper support and reduces noise and movement. What it does:

• Fastens and stabilizes an internal support brace or frame
• Prevents panel or assembly movement that can cause vibration or rattling
• Helps maintain proper alignment of connected components
• Replaces broken or corroded connector hardware to restore secure mounting

• One brace connector

• Disconnect power (and gas, if applicable) before starting any repair
• Access may require removing outer or control panels; save existing fasteners for reuse
• Use basic hand tools; avoid overtightening to prevent cracking plastic or bending metal
• Inspect and replace as needed