Kenmore 11028132410 Parts

The Lid Hinge (left) is an OEM replacement part for Whirlpool brand top-load washing machines. It is the hinge mechanism attached to the left side of the washer door assembly.

Symptoms of a bad hinge include: 

• Looseness, wobbling, or inability to securely support the weight of the washer door
• Strange noises or difficulty smoothly operating the door 
• Failure to keep the door fully open or closed
• Potential safety hazards if the door cannot be properly positioned

Causes involve wear and tear from repeated opening and closing of the washer door over many cycles, as well as damage from excessive weight loads placed on the door over time.

This Whirlpool replacement part is also compatible with Maytag, KitchenAid, and select Kenmore models.

The Hose is an OEM part for Whirlpool washing machines. This hose connects the drain pump to the outer drain hose, allowing water to empty from the washer.

Flexible yet durable, the drain hose withstands pressure during spin cycles without risk of bursting or kinking. Consistent drainage is vital for fully removing water after each cycle.

Causes of a bad hose can include cracks from extended use, mineral or soap buildup restricting flow, or stressed connections that have weakened over time.

Symptoms of a bad drain hose include:

• Incomplete drainage of water at the end of cycles
• Puddles or leaks near the pump or drain area
• Sloshing sounds of retained water inside the machine
• Enlarged hose diameter from constant pressure

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Water Valve and Fill Housing Assembly is an OEM component specifically designed for Whirlpool washing machines. This assembly includes both the water valve and housing that holds it, which work together to control water flow into the washer during operation. 

Over time, the valve and housing can experience wear or become corroded due to chemical exposure, reducing efficiency. 

Symptoms of a bad water valve and fill housing include:

• Slow or improper water fill 
• Leaks or water drips from the valve area
• Abnormal squealing or whining noises
• Inability to select certain water levels

This OEM Whirlpool replacement part is also compatible with KitchenAid, Roper, Estate, Amana, Crosley, and some Kenmore models.

The Wire Harness is an OEM part for Whirlpool washing machines. It comprises a bundle of wires that transmit electrical signals throughout the washer, connecting components like the control panel, motor, pump, and switches. The carefully designed wire routing within the protective sheathing allows all systems to operate in unison. 

Causes of a bad wire harness can be repetitive motion fatigue or damage to the insulation over many machine cycles. Constant vibration may cause wire breaks or shorts within the harness.

Symptoms of a faulty wire harness include: 

• Intermittent or unexpected operation of components  
• Inability to control wash programs or settings
• Error codes or failure detection messages
• Appliance shutting off unexpectedly 

This OEM Whirlpool part is compatible with Maytag, KitchenAid, and some Kenmore models.

This fill hose carries water from the home supply to the appliance inlet valve, restoring proper water fill and helping prevent leaks when the original hose is cracked, worn, or blocked. Ideal for replacing damaged inlet lines. What it does:

• Delivers water from the household supply to the appliance inlet valve for normal fill cycles.
• Replaces cracked, split, or deteriorated hoses that can cause leaks at connections.
• Resolves symptoms such as slow or no water fill, visible leaks, or intermittent filling.
• Durable replacement designed to match OEM routing and connection points.

• Always shut off water supply and disconnect power before starting work.
• Inspect and replace hose clamps or inlet gaskets as needed; ensure proper seating to prevent leaks.
• Hand-tighten fittings and secure clamps—avoid overtightening metal fittings.
• After installation, restore water and power and run a short fill cycle while checking for leaks.

Size: .20 Fl. Oz. (6 ml)

Screw: 8-16 x 3/8 inch.

This factory washer is used in appliance assemblies to distribute load under a fastener and maintain a secure, accurate fit. Replace a missing or damaged washer to restore proper stack-up and reduce vibration, noise, or loosening.

• Distributes load and provides proper spacing in the fastener assembly
• Helps keep bolts, screws, or nuts tight to minimize vibration and rattling
• Direct replacement when the original washer is worn, bent, cracked, or missing
• Typical signs include loose panels/brackets, recurring looseness after tightening, or new vibration after service

• Unplug the appliance; shut off water supply if working near hoses or valves
• Note the original hardware stack-up and reassemble in the same order
• Inspect mating surfaces and companion hardware; replace any damaged parts
• Tighten fasteners snugly per service guidance; avoid overtightening

Replace aging or leaking washer supply lines with this fill hose kit. It provides two 5-foot hoses to connect your home's hot and cold water valves to the washer, helping maintain a secure connection and consistent filling.

• Connects hot and cold water faucets to the washer's inlet valves
• Replace if hoses are leaking, cracked, bulging, or kinked
• Can help address slow filling caused by restricted or kinked hoses
• Useful when installing or relocating a washer

• Unplug the washer and shut off both water supply valves before starting
• Place a towel or pan to catch residual water; disconnect old hoses from faucet and washer
• Match hot to hot and cold to cold; hand-start threads to avoid cross-threading, then tighten firmly without overtightening
• Restore water and power; run a fill test and check all connections for leaks

Color: Gray. Size: 13 oz. can. Used for coating the dryer drum interior. Acrylic appliance paint.

Right Side

The Lid Hinge is an OEM part for Whirlpool washers. This hinge connects the washer lid to the cabinet and allows it to safely and securely open and close during operation.

The hinge is responsible for providing a smooth, controlled movement as well as properly securing the lid in place when closed. It ensures proper operation and functionality of the washer by facilitating easy access for loading and unloading clothes.

Causes of a bad hinge can include wear and tear over time, unbalanced loads that put excessive strain on the hinge components, or damage from impact or overextending the lid.

Symptoms of a bad hinge include:

• Difficulty opening or closing the washer lid
• The lid not staying securely closed or popping open during cycles
• Noises or squeaks coming from the hinge area
• The hinge hanging loose or off-track

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

5 foot. Package of 2.

This drain hose coupling connects two sections of the washer drain hose to restore a watertight path for wastewater, helping prevent leaks and restore proper draining. What it does:

• Joins two drain hose sections or connects hose to a mating outlet for secure water flow
• Seals the hose connection to reduce leaks at the joint
• Restores proper draining when a damaged or missing coupling causes slow drain or leakage
• Designed to fit the OEM hose profile for a snug, stable connection

• One drain hose coupling as shown

• Turn off power and water supply before starting any repair
• Inspect hose ends for damage; trim to clean cut if required for proper fit
• Push hose ends fully onto the coupling and secure with manufacturer-recommended clamps

Size: 6-32 x 9/32 inch.

This factory fastener secures appliance panels and components for a tight, rattle-free fit. Replace a missing, stripped, or corroded screw to keep assemblies aligned and performing as intended.

• Fastens panels, brackets, or assemblies in place
• Helps reduce vibration and rattling caused by loose hardware
• Maintains proper alignment of parts to prevent premature wear
• Common signs you need it: missing screw, loose panel, vibration/buzzing noises, or hardware that won't tighten

• Disconnect power; for gas or water-connected appliances, shut off supply lines before service
• Match the screw to the original; verify size, length, and thread before installation
• Start threads by hand to avoid cross-threading; use the correct driver bit
• Snug only—do not overtighten, especially into plastic or thin sheet metal